|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
07-29-2018, 06:14 PM | #1 |
Senior Member
Join Date: Jun 2014
Location: New Jersey
Posts: 1,772
|
39 accelerator peddle hole
In the floor of the 39 where the rod for accelerator peddle goes through the floor. Right now my rod is catching the floor causing the rpm to be higher than it should. Seems to me there should be some type of sleeve that holds the rod straight and prevent the rod from sliding in all sorts of directions. Am I correct or is it just a hole in floor?
Also if just a hole, any you inventor Barners make this ugly hole look and help rod from hanging up?
__________________
Thanks Andy 1952 F1 |
07-29-2018, 06:22 PM | #2 |
Senior Member
Join Date: May 2010
Location: Alabama
Posts: 3,260
|
Re: 39 accelerator peddle hole
The hinge where the pedal bolts to the wood floor is what keeps it straight. Have seen them with a small hole along with the bolt hole for a wood screw to aid in preventing the pedal from moving around. One other cause can be a worn out pedal that has a lot of wear and play in the hinge.
|
Sponsored Links (Register now to hide all advertisements) |
|
07-29-2018, 06:38 PM | #3 |
Senior Member
Join Date: May 2010
Location: Wisconsin, USA
Posts: 9,006
|
Re: 39 accelerator peddle hole
The authentic pedals had both ends turned down to form a "V" tip of sorts. Those two tips dug into the wood when the singular bolt was installed.
Also, if you've replaced the pedal, the reproduction may not have been made correctly. The authentic pedal had the hole for the rod offset to the left. Many repops I've seen have the hole in the center.
__________________
"I can explain it for you. However, I can't understand it for you". |
07-29-2018, 06:41 PM | #4 |
Senior Member
Join Date: Jun 2014
Location: New Jersey
Posts: 1,772
|
Re: 39 accelerator peddle hole
Ken, Mike
Thanks I’ll check.
__________________
Thanks Andy 1952 F1 |
07-29-2018, 07:08 PM | #5 |
Senior Member
Join Date: May 2010
Location: Napa,California
Posts: 6,037
|
Re: 39 accelerator peddle hole
If you have the rubber floor mat it can also hang up on the mat.
|
07-29-2018, 07:31 PM | #6 |
Senior Member
Join Date: Jun 2014
Location: New Jersey
Posts: 1,772
|
Re: 39 accelerator peddle hole
Sponsored Links (Register now to hide all advertisements)
__________________
Thanks Andy 1952 F1 |
07-30-2018, 07:39 AM | #7 |
Senior Member
Join Date: Oct 2016
Location: harpursville ny
Posts: 1,040
|
Re: 39 accelerator peddle hole
on mine there is a small rubber seal with a hole for the rod in the floorboard. helps keep rod centered. this seal is on the underside and is stapled to the wood.
|
07-30-2018, 08:10 AM | #8 |
Senior Member
Join Date: Jun 2014
Location: New Jersey
Posts: 1,772
|
Re: 39 accelerator peddle hole
Thanks you wouldn’t happen have a pic or part number?
__________________
Thanks Andy 1952 F1 |
07-31-2018, 07:42 AM | #9 |
Senior Member
Join Date: Oct 2016
Location: harpursville ny
Posts: 1,040
|
Re: 39 accelerator peddle hole
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|