|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
03-12-2013, 03:58 PM | #1 |
Junior Member
Join Date: Aug 2010
Location: Richmond Va.
Posts: 27
|
Advice on bench testing 34 ford radios
I have several 1934 ford radios that i want to sell on Ebay.
I want to see if they work first, can I connect the wire comming out of the radio to the positive lead of a 6 volt battery charger. and the black side of the charger to the frame or bracket of the radio. Take a look at the pictures to see if I am going to do harm to the radio. Thanks for any advice |
03-12-2013, 04:13 PM | #2 |
Senior Member
Join Date: May 2010
Location: Julesburg, Colorado
Posts: 714
|
Re: Advice on bench testing 34 ford radios
I don't think I would use a battery charger as some don't really have a set output voltage. I use a 6v battery when I test them. The old cars with these radios have a positive ground not negative ground so you want positive to go to the case of the radio. Also the radio is going to pull a good 5-10 amps. fyi
Last edited by gearhead1952; 03-12-2013 at 04:14 PM. Reason: add info |
Sponsored Links (Register now to hide all advertisements) |
|
03-12-2013, 05:06 PM | #3 | |
Senior Member
Join Date: May 2010
Location: Sugar Land, TX
Posts: 4,395
|
Re: Advice on bench testing 34 ford radios
Quote:
|
|
03-12-2013, 05:47 PM | #4 |
Senior Member
Join Date: May 2010
Location: Ashland KY
Posts: 1,159
|
Re: Advice on bench testing 34 ford radios
Don't think I would use a battery charger by its self.,could burn up a good radio,no very pure D C.
__________________
DON P |
03-13-2013, 08:03 AM | #5 |
Junior Member
Join Date: Aug 2010
Location: Richmond Va.
Posts: 27
|
Re: Advice on bench testing 34 ford radios
Sounds like I should Replace the charger with a good 6 volt battery.
The positive ground is very different to me, sounds like the hot side of the battery goes to the case and the negative side goes to the wire with the fuse? |
03-13-2013, 09:03 AM | #6 |
Senior Member
Join Date: May 2010
Location: Ashland KY
Posts: 1,159
|
Re: Advice on bench testing 34 ford radios
Sponsored Links (Register now to hide all advertisements)
__________________
DON P |
03-13-2013, 02:39 PM | #7 |
Senior Member
Join Date: May 2010
Location: San Tan Valley, Arizona
Posts: 210
|
Re: Advice on bench testing 34 ford radios
If you hook them to a battery you will probably do harm to them, making a good rebuildable radio into an expensive rebuild for someone else. Find someone in your area that works on antique tube type radios and let them test them. The vibrators rarely work in them anymore and the filter capacitors are almost gauranteed to be shot.
__________________
Wayne |
03-13-2013, 03:18 PM | #8 |
Senior Member
Join Date: Aug 2010
Location: Blenheim, New Zealand
Posts: 879
|
Re: Advice on bench testing 34 ford radios
Very rarely will you damage a radio hooking it up to a battery. In most cases it will either go or it won't, usually the latter.
The high voltage, wax encapsulated capacitors will usually be faulty and need replacing along with the main filter capacitor and often the vibrator will not function due to dirty or corroded points. All the above are repairable and just take time to do the work. So in 99% of cases even if you hook a battery up in reverse polarity you will still not damage a valve radio. Many valve car radios will operate in both polarity configurations without modification. The same cannot be said of Transistorised radios many of which will be rendered useless if connected to power in reverse polarity, mainly because they run on smoke, and if you reverse the polarity this will let the smoke out and I don't know anyone who can put the smoke back successfully
__________________
I need an 01A 1453 Brkt Spare wheel hold down for my sedan delivery - PLEASE HELP Gotta love my '42 Sedan Delivery's - Now that I own the only two in New Zealand https://www.fordbarn.com/forum/album.php?albumid=580 |
03-13-2013, 05:41 PM | #9 |
Senior Member
Join Date: Jun 2010
Location: San Antonio, Texas
Posts: 16,426
|
Re: Advice on bench testing 34 ford radios
The modern solid state vibrator replacements are polarity sensitive. The old genuine PDC vibrators not so much as long as the points & cap are working. I always loved the buzz those old vibrators made. You could tell it was working.
|
03-14-2013, 12:18 AM | #10 |
Senior Member
Join Date: May 2010
Location: franklin park ill.
Posts: 174
|
Re: Advice on bench testing 34 ford radios
no problem, you can use the 6v charger
|
03-15-2013, 08:51 PM | #11 |
Senior Member
Join Date: May 2010
Location: Encino California, near Burbank
Posts: 935
|
Testing Radios
Guys in the car radio business have a procedure to bring them up from 0 volts after checking the vibrators and caps. Just because you get away with sloppy procedures does not make it a good idea. Depends on how much you value the radios. If I were a buyer, I'd prefer an untested core.. I do understand the curiosity. Good Luck: Fred A
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|