|
|||||||
| Sponsored Links (Register now to hide all advertisements) |
|
|
 |
|
Thread Tools | Display Modes |
05-15-2022, 09:05 AM
|
#1 |
|
Junior Member
Join Date: May 2022
Posts: 6
|
recommendations
hi I'm looking for recommendations as to where to bring my 59 block flathead for machining and rebuilding in the New england area. I don't want to travel more than a few hundred miles outside of New haven Conn. How about New England engine in Peabody Mass. or R&L Engines in Dover N.H.? I'm hoping for a quick turnaround ( Maybe 3 months?)
|
|
|
|
05-15-2022, 04:24 PM
|
#2 |
|
Senior Member
Join Date: May 2010
Location: Southern Maine
Posts: 1,292
|
Re: recommendations
Advanced Engine Rebuilding in Wareham Mass.
|
|
|
|
| Sponsored Links (Register now to hide all advertisements) |
|
|
|
05-15-2022, 10:24 PM
|
#3 |
|
Senior Member
Join Date: Aug 2021
Location: Upstate N.Y.
Posts: 185
|
Re: recommendations
Al Clarke , just in eastern NY. from you. Small shop , all hands on himself.
Stretch |
|
|
|
|
05-16-2022, 06:13 AM
|
#4 |
|
Senior Member
Join Date: May 2010
Location: Capital of Corruption , NY
Posts: 765
|
Re: recommendations
I had good results with Al, too. Also a member of the Ford Barn (Jetmek).
|
|
|
|
|
05-16-2022, 08:31 AM
|
#5 |
|
Junior Member
Join Date: May 2022
Posts: 6
|
Re: recommendations
How about ronnie roadster in wallingford?
|
|
|
|
|
05-16-2022, 08:44 AM
|
#6 |
|
Senior Member
Join Date: May 2010
Location: new britain,ct 06052
Posts: 9,268
|
Re: recommendations
Sponsored Links (Register now to hide all advertisements)
Paul in CT |
|
|
|
|
05-16-2022, 09:07 AM
|
#7 |
|
Senior Member
Join Date: Oct 2011
Location: CT.
Posts: 563
|
Re: recommendations
Ronnie Roadster! Close by: shop # 203 269-1932
__________________
A man should do what he thinks best! "The Duke" |
|
|
|
|
05-16-2022, 10:34 AM
|
#8 |
|
Junior Member
Join Date: May 2022
Posts: 6
|
Re: recommendations
Thanx I'll give him a call
|
|
|
|
|
05-17-2022, 11:56 AM
|
#9 |
|
Member
Join Date: Feb 2021
Location: minnesota
Posts: 33
|
Re: recommendations
41 fatty Check my ad in the swap meet section. Motor is already machined with extras, however it is a 8ba. Thanks
|
|
|
|
|
05-17-2022, 01:21 PM
|
#10 |
|
Junior Member
Join Date: May 2022
Posts: 6
|
Re: recommendations
Thanx fifty -one f-1and all of u! Ronny Roadster recommends ernie @ A&M Auto Machine in Meriden. Ct. because his racing schedule is too tight. He won't be able to do machining till about Sept. Can I hear any feedback about A&M's reputation with early flatheads?
|
|
|
|
|
«
Previous Thread
|
Next Thread
»
| Thread Tools | |
| Display Modes | |
Linear Mode
|
|
| Sponsored Links (Register now to hide all advertisements) |
|
|
All times are GMT -5. The time now is 05:54 PM.
