Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 11-08-2019, 11:22 AM   #81
tubman
Senior Member
 
tubman's Avatar
 
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,259
Default Re: Spark Plug Protrusion into Head?

According to Champion, they are 13/16" reach, but they fit fine. After looking at the charts, I'll admit those numbers are confusing. I'll go with "hands-on" experience every time on this old stuff. Someone posted earlier in this thread than Offenhauser recommends "L" series plugs for their heads, which is obviously wrong. If you don't believe me, spend the $4.20 with Amazon and check for yourself. It beats "calling Eric".
tubman is offline   Reply With Quote
Old 11-08-2019, 11:33 AM   #82
flatjack9
Senior Member
 
flatjack9's Avatar
 
Join Date: May 2010
Location: Oshkosh, Wi
Posts: 4,516
Default Re: Spark Plug Protrusion into Head?

As they say, a picture is worth a 1000 words.
flatjack9 is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 11-08-2019, 12:04 PM   #83
Bored&Stroked
Senior Member
 
Bored&Stroked's Avatar
 
Join Date: Jan 2011
Location: Central Ohio
Posts: 5,009
Default Re: Spark Plug Protrusion into Head?

Quote:
Originally Posted by GOSFAST View Post
Just a heads-up, but to the best of my knowledge and as far back as I can recall all the "N" series Champions were 750" reach.

Believe I ran that series in my 13:1 468" years ago!

Thanks, Gary in N.Y.

P.S. Simple to find out, give a call out to federal-Mogul with the part number, they'll give you all the particulars. You can reach them at: (800) 325-8886, I spoke to Eric already this morning to confirm!
According to the NGK cross reference - it is a .750 reach plug. Hmmmmm, the plot thickens!
Bored&Stroked is offline   Reply With Quote
Old 11-08-2019, 12:19 PM   #84
GOSFAST
Senior Member
 
GOSFAST's Avatar
 
Join Date: May 2010
Location: Long Island, NY
Posts: 1,052
Default Re: Spark Plug Protrusion into Head?

That plug is the number I used in my drag car (G.M. aluminum heads), it is a reasonably "cold" plug, worked well with the 13:1 C.R.

Here's a "cut & paste" from O'Reilly Auto parts:

https://www.oreillyauto.com/
Copper Plus
Champion Copper Plus Spark Plug

(Quote)Part #120 (N5C)

Line:CHP

Check Vehicle Fit
Details
Product Information

Warranty: 1 Year Limited Warranty
Unit of Measure: Each
UPC: # 37551000869
Material Grade: Copper
Hex Size (in): 13/16 Inch
Hex Size (mm): 20mm
Thread Size: 14mm
Center Electrode Design: Standard
Thread Reach (in): 0.75 Inch
Thread Reach (mm): 19mm (.749")
Number Of Ground Electrodes: 1
Preset Gap (in): 0.023 To 0.028 Inch
Preset Gap (mm): 0.58mm To 0.71mm
Short Style Spark Plug: No
Resistor Plug: No
Ground Electrode Tip Material: Nickel-Copper Alloy
Heat Range: 5
Center Electrode Core Material: Nickel-Copper Alloy
Seat: Gasket
Ribbed Core Nose: No (End quote)

(Add) Eric was correct, after all F-M makes these Champion plugs!

Thanks, Gary in N.Y.

P.S. I believe the "13/16" being mentioned above is most like the wrench size, just a hunch here though??
Attached Images
File Type: jpg Spark Plugs Champion-NC5 750 Lg.jpg (30.7 KB, 14 views)
GOSFAST is offline   Reply With Quote
Old 11-08-2019, 01:07 PM   #85
AnthonyG
Senior Member
 
AnthonyG's Avatar
 
Join Date: May 2013
Location: Pa.
Posts: 2,161
Default Re: Spark Plug Protrusion into Head?

I got 8 coming in a couple. I’ll let all know, looks good in tubman’s pic! Great thing about Amazon as a Prime member u can return no cost��
__________________
Nomad
AnthonyG is offline   Reply With Quote
Old 11-08-2019, 03:42 PM   #86
mfirth
Senior Member
 
Join Date: Aug 2017
Location: ohio
Posts: 986
Default Re: Spark Plug Protrusion into Head?

Sponsored Links (Register now to hide all advertisements)
O K, i gotta get back in here after look'n at some older posts where several guys are runnung 216 & 437 Autolites, NGK BL6's & 4's and non of them indicated any problems with pre-ign. spark knock, heating issues etc.and seem quite happy with performance.
I'm just not so concerned now...???
I sure do admire & appreciate you fella's with so much experience & knowlege though. Thanks 4 keeping guys like me advised. mike
mfirth is offline   Reply With Quote
Old 11-08-2019, 09:44 PM   #87
tubman
Senior Member
 
tubman's Avatar
 
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,259
Default Re: Spark Plug Protrusion into Head?

"AnthonyG" (and "Mart") - I am not in a position to do some actual clearance testing with these plugs. I did however take a picture of a set of "N" series plug in my unmolested Offenhauser heads as well as a regular plug in an 8BA iron head. As you can see, it looks like the stock setup is a bit more recessed than the modified setup. Given this, I would follow "Mart"'s advice and clay this set up upon assembly. I don't think there would be a problem, but you can never be sure. I hope everything works out.

"AnthonyG" - I am glad that you brought this up, as it appears to have been a continuing problem through the years. I have been reconstructing in my mind what I went through. I think I came to the right conclusion in 1961 after trying many different types of Champion plugs and seemed to have forgotten it by 1994 when I used the outboard motor "surface gap" plugs (although they worked fine). Please get back to us after you get the engine together and running so we can determine the definitive answer to what plugs to run in Offenhauser heads (it seems that Offenhauser doesn't have a clue). I don't know that the heat range (the "5" in "N5") is correct; I just used it because it is in the middle of the heat range. Also, while I believe the right size plug is mandatory, the brand is not, so you may want to try some others. In addition, from Gary's "GOSFAST" comments, I think that some plugs said to be compatible aren't.

Good luck and keep us informed.

(I have included a couple of other pictures because the difference between the "L" series and "N" series is remarkable.)
Attached Images
File Type: jpg IMG_1680.jpg (69.7 KB, 83 views)
File Type: jpg IMG_1681.jpg (64.5 KB, 85 views)
File Type: jpg IMG_1684.jpg (65.6 KB, 76 views)
File Type: jpg IMG_1685.jpg (39.1 KB, 72 views)

Last edited by tubman; 11-08-2019 at 10:24 PM.
tubman is offline   Reply With Quote
Old 11-09-2019, 01:10 AM   #88
40 Deluxe
Senior Member
 
Join Date: May 2010
Location: now Kuna, Idaho
Posts: 3,774
Default Re: Spark Plug Protrusion into Head?

How about this scenario: reach of plug without gasket (total shank length)=13/16". Reach of plug with gasket installed=3/4" (assuming gasket is 1/16" thick). Anyway, the end result is what's important, and it looks like Tubman has it figured out!
40 Deluxe is offline   Reply With Quote
Old 11-09-2019, 08:58 AM   #89
Bored&Stroked
Senior Member
 
Bored&Stroked's Avatar
 
Join Date: Jan 2011
Location: Central Ohio
Posts: 5,009
Default Re: Spark Plug Protrusion into Head?

With a high-lift cam, wonder if the valves will hit the spark plug ground strap? Sure looks like it. I would test fit on an engine where you know the exhaust valve is at full lift. Make sure you do it on the side where the valve is higher from the deck.

FYI: Given the valve angles/heights are different side to side, there was a time when Edelbrock actually made a left and right head - the cast chambers were different side to side. I bet the new NC machined ones are non side-specific.
Bored&Stroked is offline   Reply With Quote
Old 11-09-2019, 10:26 AM   #90
AnthonyG
Senior Member
 
AnthonyG's Avatar
 
Join Date: May 2013
Location: Pa.
Posts: 2,161
Default Re: Spark Plug Protrusion into Head?

Got it tubman & Thx again 4 the great work!
__________________
Nomad
AnthonyG is offline   Reply With Quote
Old 11-13-2019, 04:36 PM   #91
AnthonyG
Senior Member
 
AnthonyG's Avatar
 
Join Date: May 2013
Location: Pa.
Posts: 2,161
Default Re: Spark Plug Protrusion into Head?

Obviously my Offy heads depth of thread different than tubman’s. The Champion N5C’s R indeed 3/4 reach and extend into the head chamber almost 4 full threads. Oh well there going back to Amazon & guessing I’ll pull the other head & just Chamfer for the Autolite 437’s
Attached Images
File Type: jpg image.jpg (39.2 KB, 42 views)
__________________
Nomad
AnthonyG is offline   Reply With Quote
Old 11-13-2019, 05:21 PM   #92
tubman
Senior Member
 
tubman's Avatar
 
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,259
Default Re: Spark Plug Protrusion into Head?

Boy, that's strange! I wonder if someone has modified your heads or they are from different production periods. Mine came straight from Speedway in the late '90's and have been sitting on the shelf ever since because of my involvement with the Edmunds heads, and I know they haven't been messed with.

Anthony, would it be possible to get a close up photo of the top of the spark plug hole? Except for the carbon, the bottom looks just like mine.
tubman is offline   Reply With Quote
Old 11-13-2019, 05:39 PM   #93
AnthonyG
Senior Member
 
AnthonyG's Avatar
 
Join Date: May 2013
Location: Pa.
Posts: 2,161
Default Re: Spark Plug Protrusion into Head?

Heads don’t show any evidence of additional machining on either side of spark plug threaded holes. Light spot-faces on outside of head where plugs wire connect end is. No chamfer or counter bore on inside, threads enter as-cast chamber area. Guess it could be a different model design? I had an 8BA built by Jerry Livingston, owner of United Engine Specialists in Wichita Ka. Only marking on the head is the Offenhauser cast in & a 400 stamped on top side near temp gauge threaded hole see in pic.
Attached Images
File Type: jpg image.jpg (29.3 KB, 44 views)
__________________
Nomad
AnthonyG is offline   Reply With Quote
Old 11-13-2019, 06:38 PM   #94
AnthonyG
Senior Member
 
AnthonyG's Avatar
 
Join Date: May 2013
Location: Pa.
Posts: 2,161
Default Re: Spark Plug Protrusion into Head?

Not sure why but can’t get photos to load for some reason? Sorry? As I said though the view from the top shows spot-faces on each to same depth clean machining the casting. Most casting removed is shy of 1/16” the rest r about 1/32”. I’ll try to load photos again later.
__________________
Nomad

Last edited by AnthonyG; 11-13-2019 at 06:59 PM. Reason: Picture didn’t losd
AnthonyG is offline   Reply With Quote
Old 11-14-2019, 09:58 AM   #95
tubman
Senior Member
 
tubman's Avatar
 
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,259
Default Re: Spark Plug Protrusion into Head?

Anthony, Going on the assumption (which may not be correct) that your heads were modified to fit some particular type of spark plug in the past, I think it may be more productive to try to figure out what that plug was than to further modify your heads. Any modification would probably reduce the number of threads holding the plug, which is not a good thing with aluminum heads. In one of my posts I posted a link to a site that has the parameters for most brands of plugs, including reach. I think that some time going through those tables to see if there is something out there that may fit the heads as they are now would be more productive than cutting the heads again.

Here is that link again : https://www.sparkplugs.com/learning-...bering-systems.

I find the Champion table to be the most comprehensive and usually use it. If you find what you want, but don't like Champions, you can always find another brand that will cross-reference to the Champion plug.

Last edited by tubman; 11-14-2019 at 10:03 AM.
tubman is offline   Reply With Quote
Old 11-14-2019, 10:12 AM   #96
AnthonyG
Senior Member
 
AnthonyG's Avatar
 
Join Date: May 2013
Location: Pa.
Posts: 2,161
Default Re: Spark Plug Protrusion into Head?

Thx tubman, I have the site & will check again. Really not being stubborn but as a retired Tool & Die Guy I can tell the heads not modified! U previously indicated it may be a different model # & that may be it. Thx & I’m working on figuring out how to reduce the file size on Pics so I can post.
__________________
Nomad
AnthonyG is offline   Reply With Quote
Old 11-14-2019, 10:23 AM   #97
AnthonyG
Senior Member
 
AnthonyG's Avatar
 
Join Date: May 2013
Location: Pa.
Posts: 2,161
Default Re: Spark Plug Protrusion into Head?

Pic of top of head
Attached Images
File Type: jpg A0D47287-2934-4B67-965A-501F14A5ED17.jpg (77.3 KB, 44 views)
__________________
Nomad
AnthonyG is offline   Reply With Quote
Old 11-14-2019, 10:47 AM   #98
tubman
Senior Member
 
tubman's Avatar
 
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,259
Default Re: Spark Plug Protrusion into Head?

From the picture, it sure looks like the heads weren't modified. On the plug hole on the right, you can see the complete set of threads. I'll try to take a picture of my head from the same angle and see if I can get a comparable view. BTW, my heads are stamped "425". As I said, my heads were procured from Speedway in the late nineties; do you have any idea of the age of your heads?
tubman is offline   Reply With Quote
Old 11-14-2019, 11:01 AM   #99
AnthonyG
Senior Member
 
AnthonyG's Avatar
 
Join Date: May 2013
Location: Pa.
Posts: 2,161
Default Re: Spark Plug Protrusion into Head?

Hard to say age on mine, as said procured engine w heads on. United Engines Specialists has a Flathead only dept so assuming they have heads they’ve bought in bulk on the shelf who knows how old. I’d think ur’s marked 425 indicate sequentially a more recent run? Scale the reach on the N5C’s u have. If they’re actually 3/4” as spec indicates it’s the reason they’re not fitting mine. Calculating mine require 5/8” reach which Don’t seem to exist?
__________________
Nomad

Last edited by AnthonyG; 11-14-2019 at 11:14 AM.
AnthonyG is offline   Reply With Quote
Old 11-14-2019, 01:23 PM   #100
flatjack9
Senior Member
 
flatjack9's Avatar
 
Join Date: May 2010
Location: Oshkosh, Wi
Posts: 4,516
Default Re: Spark Plug Protrusion into Head?

The 425 refers to the relative depth of the cylinder head. The larger number can take a higher lift cam.
flatjack9 is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 10:26 AM.