The Ford Barn

01-01-1970, 12:00 AM

3/4 ton and tonner shared the same grill as the 1.5 ton, which is totally different then the .5 ton.

01-01-1970, 12:00 AM

Thanks everyone for the information. You have been a great help. This gives us a lot to go on.

03-24-2005, 04:38 PM

Is the hood on a 41 PU the same as a 40 PU?

My friend tried to put one of Drake's 40 PU nose pieces on his 41 and it wouldn't fit the contour. Is there a problem with the nose piece from Bob or are the hoods different? Thanks for your response.

03-24-2005, 04:43 PM

there are two different hood/grille combo's for 40/41 pickups.

03-24-2005, 05:34 PM

Let me get this straight. Are you saying that the actual sheet metal is different between the 40 and 41 pickup? We know about the trim pieces and they are different.

03-24-2005, 05:54 PM

Sponsored Links (Register now to hide all advertisements)

what i am saying is there was 2 different styles for 40 and 41 .there was the style of the car and then there was a truck style hood/grille.they were close in looks ,yet totally different.the cab was the same but fenders,hood ,grille,close but not a match.

03-25-2005, 04:20 AM

http://www.vanpeltsales.com/FH_web/f...1940trucks.htm

03-25-2005, 05:05 AM

As for the differences, the '40 hood pot metal trim that goes down the front should fit the hood, BUT there is a difference in the length(at fthe front bottom). Drake makes ONE piece that will fit both models. What he did was to make the trim piece to fit the longest version. Thereby fitting both & if needed you cut off a couple inches if your needs are for the shorter one. I went thru this situation myself a couple yrs ago.

My hood & the trim did NOT fit either & after doing a go around several times, it was discovered that my hood had been banged up a time or two and after reworking the hood to bring it back to original contours, everything worked out.

03-25-2005, 10:13 AM

probably not your problem BUT 41 had a 6 cyl that used different hood latch bracing than 4 or V8...

03-25-2005, 05:01 PM

I have a '41 and just sold a '40. Hoods are the same exept for the latch mechanism is farther ahead on the '41 (and it was'nt a 6 cyl) I think all '41's came with the further ahead design. The '40 trim won't hook up to the '41 linkage and latch either. Also if you look at the upper grille support the cross bar where the latch hooks on to is further ahead than the '40 as well. The 'car' bullnose looks the same but is different as well, could he have rec'd a car bullnose my mistake?

My 2 cents. thanks.

01-01-1970, 12:00 AM	#1
Guest Posts: n/a	Re: 1941 Ford Half Ton Pickup 3/4 ton and tonner shared the same grill as the 1.5 ton, which is totally different then the .5 ton.

01-01-1970, 12:00 AM	#2
Guest Posts: n/a	Re: 1941 Ford Half Ton Pickup Thanks everyone for the information. You have been a great help. This gives us a lot to go on.

03-24-2005, 04:38 PM	#3
Guest Posts: n/a	1941 Ford Half Ton Pickup Is the hood on a 41 PU the same as a 40 PU? My friend tried to put one of Drake's 40 PU nose pieces on his 41 and it wouldn't fit the contour. Is there a problem with the nose piece from Bob or are the hoods different? Thanks for your response.

03-24-2005, 04:43 PM	#4
Guest Posts: n/a	Re: 1941 Ford Half Ton Pickup there are two different hood/grille combo's for 40/41 pickups.

03-24-2005, 05:34 PM	#5
Guest Posts: n/a	Re: 1941 Ford Half Ton Pickup Let me get this straight. Are you saying that the actual sheet metal is different between the 40 and 41 pickup? We know about the trim pieces and they are different.

03-24-2005, 05:54 PM	#6
Guest Posts: n/a	Re: 1941 Ford Half Ton Pickup Sponsored Links (Register now to hide all advertisements) what i am saying is there was 2 different styles for 40 and 41 .there was the style of the car and then there was a truck style hood/grille.they were close in looks ,yet totally different.the cab was the same but fenders,hood ,grille,close but not a match.

03-25-2005, 04:20 AM	#7
Guest Posts: n/a	Re: 1941 Ford Half Ton Pickup http://www.vanpeltsales.com/FH_web/f...1940trucks.htm

03-25-2005, 05:05 AM	#8
Guest Posts: n/a	Re: 1941 Ford Half Ton Pickup As for the differences, the '40 hood pot metal trim that goes down the front should fit the hood, BUT there is a difference in the length(at fthe front bottom). Drake makes ONE piece that will fit both models. What he did was to make the trim piece to fit the longest version. Thereby fitting both & if needed you cut off a couple inches if your needs are for the shorter one. I went thru this situation myself a couple yrs ago. My hood & the trim did NOT fit either & after doing a go around several times, it was discovered that my hood had been banged up a time or two and after reworking the hood to bring it back to original contours, everything worked out.

03-25-2005, 10:13 AM	#9
Guest Posts: n/a	Re: 1941 Ford Half Ton Pickup probably not your problem BUT 41 had a 6 cyl that used different hood latch bracing than 4 or V8...

03-25-2005, 05:01 PM	#10
Guest Posts: n/a	Re: 1941 Ford Half Ton Pickup I have a '41 and just sold a '40. Hoods are the same exept for the latch mechanism is farther ahead on the '41 (and it was'nt a 6 cyl) I think all '41's came with the further ahead design. The '40 trim won't hook up to the '41 linkage and latch either. Also if you look at the upper grille support the cross bar where the latch hooks on to is further ahead than the '40 as well. The 'car' bullnose looks the same but is different as well, could he have rec'd a car bullnose my mistake? My 2 cents. thanks.