Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 09-27-2021, 07:02 AM   #1
russcc
Senior Member
 
Join Date: May 2010
Posts: 2,871
Default Variable coil ballast resistor

Using a Skip re-built, converted to 12V, negative ground !GA coil on the 59 in the roadster. The ballast resistor is a round, adjustable unit. Photo. I am getting 8V at the Ignition side of the coil while the engine is running, and I would like to get down to 3.8 to 4.2 volts to the coil. Anyone know how to change the resistance in this type of resistor ? Thank you.
Attached Images
File Type: jpg IMG_1688.JPG (129.3 KB, 58 views)
russcc is offline   Reply With Quote
Old 09-27-2021, 07:15 AM   #2
corvette8n
Senior Member
 
corvette8n's Avatar
 
Join Date: Jul 2010
Location: 36 miles north of Albany NY
Posts: 2,931
Default Re: Variable coil ballast resistor

Hey Russ, does anything twist or slide, I can’t tell from the pictures.
corvette8n is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 09-27-2021, 07:42 AM   #3
russcc
Senior Member
 
Join Date: May 2010
Posts: 2,871
Default Re: Variable coil ballast resistor

I believe you may change the stud position. My mistake, I have 8V at the coil, and would like to get it around 5.5V at the coil, because the coil should drop it to 4.0 volts to the points. Please correct me if I am off base.
russcc is offline   Reply With Quote
Old 09-27-2021, 10:44 AM   #4
tubman
Senior Member
 
tubman's Avatar
 
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,260
Default Re: Variable coil ballast resistor

It think you are right about different stud locations having different resistances. It would be easy to check out if you have a multi-meter (set to ohms).
tubman is offline   Reply With Quote
Old 09-27-2021, 11:59 AM   #5
russcc
Senior Member
 
Join Date: May 2010
Posts: 2,871
Default Re: Variable coil ballast resistor

I do have multi-m, and I get aprox. 3-0hms at the lowest post where it is market 3 volts.
I have other ballast resistors of which I will post a photo later. They seem to all be around 3 ohms.
russcc is offline   Reply With Quote
Old 09-27-2021, 12:14 PM   #6
russcc
Senior Member
 
Join Date: May 2010
Posts: 2,871
Default Re: Variable coil ballast resistor

Sponsored Links (Register now to hide all advertisements)
These 3 ballast resistors all read about 3 OHMS.
Attached Images
File Type: jpg IMG_1684.JPG (162.7 KB, 14 views)
russcc is offline   Reply With Quote
Old 09-27-2021, 04:24 PM   #7
Jack E/NJ
Senior Member
 
Jack E/NJ's Avatar
 
Join Date: May 2010
Posts: 2,171
Default Re: Variable coil ballast resistor

>>>Using a Skip re-built, converted to 12V, negative ground !GA coil on the 59 in the roadster.>>>


Prolly ~1.5 ohm primary. I'm using a ~2 ohm chrysler ballast with mine. No bypass. It's fine.
Jack E/NJ is offline   Reply With Quote
Old 09-27-2021, 05:34 PM   #8
russcc
Senior Member
 
Join Date: May 2010
Posts: 2,871
Default Re: Variable coil ballast resistor

So if the coil has 1.5 ohms resistance, and ballast resistor 2 ohms what would the current in amps be in 12V circuit ? How do I measure the voltage to see if I have 3.8 to 4.2 volts at the points ? Thank you.
russcc is offline   Reply With Quote
Old 09-27-2021, 06:31 PM   #9
JSeery
Member Emeritus
 
JSeery's Avatar
 
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
Default Re: Variable coil ballast resistor

To some extent these numbers/ calculations are just appropriations. The operating voltage is more like 14+, not 12. The resistance changes with temperature. There are other factors involved besides just the ballast resistor and coil, such as wire size and length and any other current paths in the circuit. And etc, etc, etc. So 3.0 ohms resistance and 12 volts are just ballpark talking points.
JSeery is offline   Reply With Quote
Old 09-27-2021, 08:26 PM   #10
Jack E/NJ
Senior Member
 
Jack E/NJ's Avatar
 
Join Date: May 2010
Posts: 2,171
Default Re: Variable coil ballast resistor

>>>So if the coil has 1.5 ohms resistance, and ballast resistor 2 ohms what would the current in amps be in 12V circuit ? How do I measure the voltage to see if I have 3.8 to 4.2 volts at the points ? Thank you.>>>




Ohm's law calculations
Points closed, engine not running = 0 volts at the ungrounded point, 3.6 amps.

Points open. engine not running = 12.6 volts at the ungrounded point, 0 amps.


Ohm's law conclusions
Ignition switch left on, engine not running = good chance of fried coil and dead battery. 8^)
Jack E/NJ is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 01:18 AM.