Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 01-29-2018, 06:24 AM   #1
tinman080
Senior Member
 
tinman080's Avatar
 
Join Date: Oct 2015
Location: Forest, Virginia
Posts: 250
Default License plate restoration

My brother-in-law wanted a set of vintage plates for his 1930 Tudor. Old Virginia plates as a matched set are difficult to find and pricey when found. Anyway he found a set. Cracked here and there, and a couple of extra holes where nailed up in a barn somewhere, I imagine. They had a mild case of rust pitting, but enough color left to accurately repaint them. He brought them to me and I started by cleaning them up. I wire brushed and sandblasted them a little, then welded up the cracks and extra holes. After grinding the welded areas I skimmed them both with body filler. A good sanding, about 3 coats of lacquer primer. I scuff padded both with red pads then shot the backs with black, taking care to cover the outside edges completely. Once the backs dried WELL, I taped all the holes from the backside to prevent blow- thru overspray. I ran a piece of tape around the outer edges facing up, then laid the plates on cardboard and taped that line of tape down from the front to prevent overspray around the edges. Clear as mud....Then I shot the fronts with black. I was fortunate that Rustoleum makes an orange color that's a dead ringer for the original color. I actually masked all the letters and numbers off, I've developed a tremor in my rt arm since I retired and free- handing a paint line ain't gonna happen no more. lol I shot the orange on and pulled the tape while wet. Enamel leaves a clean line like stripe tape if the masking tape is pulled before the paint dries. Be careful! Jon was happy with them. Gary ***A license plate WARNING*** Virginia and many other states allow registering your vintage car with original year plates, BUT check the numbers with DMV because this set of plate numbers were reissued on on a modern Va tag, The modern tag takes priority so these tags can't be actually driven on.....
Attached Images
File Type: jpg 0425171131a (Small).jpg (26.4 KB, 207 views)
File Type: jpg 0422171205 (Small).jpg (48.7 KB, 199 views)
File Type: jpg 0507171730a (Small).jpg (51.3 KB, 204 views)
File Type: jpg 0510170630 (Small).jpg (47.3 KB, 293 views)
__________________
Just Passin' Thru.....Slowly!

Last edited by tinman080; 01-29-2018 at 06:37 AM.
tinman080 is offline   Reply With Quote
Old 01-29-2018, 06:42 AM   #2
Fairview
Member
 
Join Date: Dec 2010
Location: Waynesboro, Virginia
Posts: 67
Default Re: License plate restoration

Great job! I’ve got a set of 29 Virginia plates that need the same treatment. Those are orange with black numbers. Can you post the name or number of the orange Rustoleum? And do I understand that you used masking tape for all the letters and numbers? That is quite a task!
Fairview is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 01-29-2018, 06:56 AM   #3
tinman080
Senior Member
 
tinman080's Avatar
 
Join Date: Oct 2015
Location: Forest, Virginia
Posts: 250
Default Re: License plate restoration

Quote:
Originally Posted by Fairview View Post
Great job! I’ve got a set of 29 Virginia plates that need the same treatment. Those are orange with black numbers. Can you post the name or number of the orange Rustoleum? And do I understand that you used masking tape for all the letters and numbers? That is quite a task!
Hiya Fairview, carry your tag to Lowes, the orange is in spray-bombs or quart cans. 2 different oranges are available, one yellowish and one more red. The redder one I used. The materials I had left I gave to the brother in law. Gary
__________________
Just Passin' Thru.....Slowly!
tinman080 is offline   Reply With Quote
Old 01-29-2018, 07:02 AM   #4
tinman080
Senior Member
 
tinman080's Avatar
 
Join Date: Oct 2015
Location: Forest, Virginia
Posts: 250
Default Re: License plate restoration

The masking tape I cut along the edge of the roll with a razor knife, from 1/16th wide to go around the tiny curves and widening the tape as I moved out to more open areas. Gary
__________________
Just Passin' Thru.....Slowly!
tinman080 is offline   Reply With Quote
Old 01-29-2018, 07:57 AM   #5
3.6rs
Senior Member
 
3.6rs's Avatar
 
Join Date: Jul 2010
Location: Belgistan (formerly known as Belgium)
Posts: 573
Default Re: License plate restoration

I restored dozens, no, hundreds of antique license plates. I never used spray-bombs and tape! I did them all by hand. The first ones are difficult but once you get a steady hand it's an easy job.
3.6rs is offline   Reply With Quote
Old 01-29-2018, 08:07 AM   #6
Terry, NJ
Senior Member
 
Terry, NJ's Avatar
 
Join Date: May 2010
Location: Bucks Co, Pa
Posts: 3,740
Default Re: License plate restoration

Sponsored Links (Register now to hide all advertisements)
I, too, have tremors in my hands. But I was given a 1930 Pennsylvania plate that needed a lot of TLC, welding, etc, just like you describe. This plate can be seen in my profile. It's not restorer grade, but it's a good ten footer.
Terry
Terry, NJ is offline   Reply With Quote
Old 01-29-2018, 09:17 AM   #7
tinman080
Senior Member
 
tinman080's Avatar
 
Join Date: Oct 2015
Location: Forest, Virginia
Posts: 250
Default Re: License plate restoration

Quote:
Originally Posted by 3.6rs View Post
I restored dozens, no, hundreds of antique license plates. I never used spray-bombs and tape! I did them all by hand. The first ones are difficult but once you get a steady hand it's an easy job.
Unfortunately at 67 years old I have lost the steady hands. Patience, masking tape, age and cunning can overcome many adversaries....
__________________
Just Passin' Thru.....Slowly!
tinman080 is offline   Reply With Quote
Old 01-29-2018, 09:46 AM   #8
jhowes
Senior Member
 
Join Date: Jul 2010
Location: upstate NY near Mass border
Posts: 789
Default Re: License plate restoration

Same problem as Tinman080. My shaky hands are 82 years old. The rest of me is catching up real fast. Like the roll of toilet paper, "the closer to the end you get the faster it goes. Jack
jhowes is offline   Reply With Quote
Old 01-29-2018, 09:55 AM   #9
Afordman31
Senior Member
 
Afordman31's Avatar
 
Join Date: May 2010
Location: Michigan
Posts: 577
Default Re: License plate restoration

Tinman080
Very nice license plate. Was looking at your profile and would like to see more pictures in the future of the Ranger speedster.......you are very innovated. Thanks for the post.
Afordman31 is offline   Reply With Quote
Old 01-29-2018, 10:05 AM   #10
burner31
Senior Member
 
burner31's Avatar
 
Join Date: Dec 2014
Location: Shawnee, Ok
Posts: 3,471
Default Re: License plate restoration

Here ya go
Attached Images
File Type: jpg 0422171205 (Small).jpg (48.7 KB, 71 views)
File Type: jpg 0425171131a (Small).jpg (17.6 KB, 65 views)
File Type: jpg 0510170630 (Small).jpg (30.0 KB, 107 views)
__________________
Keith
Shawnee OK
'31 SW 160-B
burner31 is offline   Reply With Quote
Old 01-29-2018, 12:46 PM   #11
cpf240
Senior Member
 
cpf240's Avatar
 
Join Date: Feb 2017
Location: Northern Idaho
Posts: 282
Default Re: License plate restoration

You guys make me jealous. I don't have those skills (yet). I sent my YOM plate out to get restored before the DMV would accept it.

I am very happy with the work done on my plate by Brian Mabry of Finish Your Plates.
No, I'm not affiliated with him in any way, other than I paid him to refinish my plate.
cpf240 is offline   Reply With Quote
Old 01-29-2018, 12:53 PM   #12
slammin
Senior Member
 
slammin's Avatar
 
Join Date: Aug 2017
Location: Fruita, CO
Posts: 281
Default Re: License plate restoration

tinman080,
Beautiful job on those plates. This is a very timely thread. After months of looking for a 1929 Colorado plate that wasn't a kings ransom, my plate arrived Saturday. Aside from needing paint, its in very good shape. I have Horseless Carriage plates on the car and don't know if the DMV will get their boxers in a bunch if I would display a YOM plate as well.
slammin is offline   Reply With Quote
Old 01-29-2018, 01:06 PM   #13
tinman080
Senior Member
 
tinman080's Avatar
 
Join Date: Oct 2015
Location: Forest, Virginia
Posts: 250
Default Re: License plate restoration

Slammin a quick visit to DMV will tell you....lol... maybe! Afordman31 I'm itching to get going. I had a heart attack December 12th. I'm hoping to be up to speed soon so I can get rolling. Thanks for all the kind responses. Gary
__________________
Just Passin' Thru.....Slowly!
tinman080 is offline   Reply With Quote
Old 01-29-2018, 01:11 PM   #14
BillCNC
Senior Member
 
BillCNC's Avatar
 
Join Date: Aug 2017
Location: SoCal Desert
Posts: 826
Default Re: License plate restoration

tinman080,

With plates like those that have been reissued, I would think the DMD could send a letter (at your cost) to make an offer of purchase (by you) for the reissued plates to the new owner. Once you have the plate's, offer them to the DMV and see if they will reissue the numbers back to the original plates?

The worst thing they could do, ... Is say no, ... the default answer if you don't ask.

I've gotten away with a whole lot of thing's just by asking more than one person. Last time about a year ago, ... $800.00 off of past registration fee's for a 1990 f-150 and registered it non-opp.

Regards
Bill
BillCNC is offline   Reply With Quote
Old 01-29-2018, 05:46 PM   #15
tinman080
Senior Member
 
tinman080's Avatar
 
Join Date: Oct 2015
Location: Forest, Virginia
Posts: 250
Default Re: License plate restoration

BillCNC, the plates are my brother-in-laws and I'm not involved in the number fiasco. The DMV'S position is the number is the number, the year does not matter. I guess he will do what he wants. Thanks for the good advice.
__________________
Just Passin' Thru.....Slowly!
tinman080 is offline   Reply With Quote
Old 01-29-2018, 08:00 PM   #16
BILL WILLIAMSON
Senior Member
 
BILL WILLIAMSON's Avatar
 
Join Date: Dec 2010
Location: FRESNO, CA
Posts: 12,560
Default Re: License plate restoration

Ted couldn't use his 1930 plates, the same number was on a Motorcycle, somewhere???
Bill W.
__________________
"THE ASSISTANT GURU OF STUFF"
BILL WILLIAMSON is offline   Reply With Quote
Old 01-29-2018, 11:16 PM   #17
vern hodgson
Senior Member
 
Join Date: Dec 2014
Location: langley, wa.
Posts: 642
Default Re: License plate restoration

Quote:
Originally Posted by tinman080 View Post
The masking tape I cut along the edge of the roll with a razor knife, from 1/16th wide to go around the tiny curves and widening the tape as I moved out to more open areas. Gary
Years ago you could buy very thin tape under the name of chartpak. Used tons of it in drafting. Thanks for reminding me. Better than masking tape I believe, and no. Cutting.
vern hodgson is offline   Reply With Quote
Old 02-01-2018, 05:02 PM   #18
tinman080
Senior Member
 
tinman080's Avatar
 
Join Date: Oct 2015
Location: Forest, Virginia
Posts: 250
Default Re: License plate restoration

Quote:
Originally Posted by vern hodgson View Post
Years ago you could buy very thin tape under the name of chartpak. Used tons of it in drafting. Thanks for reminding me. Better than masking tape I believe, and no. Cutting.
I could have used 3M fineline, in fact I used tons of it in my body shop career; but I like using a single edge razor blade on 3M crepe style masking tape. I know what results I will get. Using a spray bomb on a license plate is perfectly fine if the preparation is adequate and the quality of the paint is top notch. Painting a car with fingernail paint is absolutely fine if the prep is good, the paint is good and that's what the owner wants. The black car is 2 coats of acrylic enamel single stage over lacquer primer on 3/4'' plywood. The green car is 3 coats of acrylic enamel single stage over lacquer primer over 3/4'' plywood. No clear coat. Both kept inside, don't need it. Good results can be had with ''cheap'' products if care is used. Thanks, Gary
Attached Images
File Type: jpg DSCN1665 (Small).JPG (155.4 KB, 55 views)
File Type: jpg DSCN0003 (Small).JPG (170.6 KB, 56 views)
__________________
Just Passin' Thru.....Slowly!

Last edited by tinman080; 02-01-2018 at 05:50 PM.
tinman080 is offline   Reply With Quote
Old 02-02-2018, 05:41 PM   #19
CHuDWah
Senior Member
 
CHuDWah's Avatar
 
Join Date: Dec 2010
Location: Kritter Krick, Flaw-duh
Posts: 1,158
Default Re: License plate restoration

Here's a quick and dirty method I've used on stuff with raised letters/numbers like license plates. Spray the piece with a couple fairly heavy coats of the letter/number color. Then spray it with a light coat of the background color - just enough to cover the first color. Finally, sand the background color off the raised areas. Maybe not "fine point" results but still nice and a lot easier than masking.

Re displaying YOM plates, my car had dual tail lights - I had current plate on left and YOM on right. Never had a problem - your state's mileage may vary.
CHuDWah is offline   Reply With Quote
Old 02-02-2018, 07:57 PM   #20
Chris Haynes
Senior Member
 
Chris Haynes's Avatar
 
Join Date: May 2010
Location: Camarillo, CA and Pine Grove, CA
Posts: 2,830
Default Re: License plate restoration

I found a nice pair of original CA plates for my '30 Tudor. Only problem is that number is being used on a modern plate on a Harley.
__________________
1921 Runabout
1930 Tudor
Early 1930 AA
Speed costs money. How fast do you want to go?
Chris Haynes is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 09:24 AM.