|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
03-19-2018, 11:34 PM | #1 |
Senior Member
Join Date: May 2010
Location: Lakeville, MN
Posts: 5,159
|
Acetylene regulator
I think my Victor acetylene regulator of 30 years has given up the ghost. I was looking at acetylene regulators on eBay and there are a lot of cheap, I assume China made, regulators for $25 to $40. The Victor regulators are $100 and a lot higher. That is a big difference in prices. I am wondering if there is a big difference in the function of the regulators. I am an occasional user, mostly using the torch to heat rusted nuts and bolts to free them. If anyone has information on the cheaper ones as far as working OK or not, please post their experience.
Rusty Nelson |
03-19-2018, 11:41 PM | #2 |
Senior Member
Join Date: Aug 2017
Location: SoCal Desert
Posts: 826
|
Re: Acetylene regulator
For what it's worth, I have a couple of Chinese regulators that I use for Argon and another for Acetylene. They have been working flawlessly for about 5 years now.
Regards Bill |
Sponsored Links (Register now to hide all advertisements) |
|
03-20-2018, 03:52 AM | #3 |
Senior Member
Join Date: Sep 2010
Location: South Coast NSW Australia
Posts: 2,596
|
Re: Acetylene regulator
I ditched acetylene, now use LPG.
No bottle rent. |
03-20-2018, 06:35 AM | #4 |
Senior Member
Join Date: Mar 2015
Location: Greenville, SC
Posts: 1,099
|
Re: Acetylene regulator
Most welding supply stores can have them overhauled in the area of $100. I would check on that before purchasing what could be C'junk.
John |
03-20-2018, 08:35 AM | #5 |
Senior Member
Join Date: Aug 2011
Location: Battle Ground WA
Posts: 293
|
Re: Acetylene regulator
There are single stage and dual stage regulators. If you want steady pressure control, like for welding, you will want a dual stage regulators. Some of the cheapies are ok, just make sure you get a dual stage.
|
03-20-2018, 08:44 AM | #6 |
Senior Member
Join Date: May 2010
Location: Lakeville, MN
Posts: 5,159
|
Re: Acetylene regulator
Sponsored Links (Register now to hide all advertisements)
Rusty Nelson |
03-20-2018, 09:22 AM | #7 |
Senior Member
Join Date: May 2010
Posts: 313
|
Re: Acetylene regulator
|
03-20-2018, 10:01 AM | #8 |
Senior Member
Join Date: May 2010
Location: Southern,Maine
Posts: 141
|
Re: Acetylene regulator
Try the Garage Journal (sister site) great & knowable people.
Bob |
03-20-2018, 10:18 AM | #9 |
Senior Member
Join Date: May 2010
Location: Portland OR
Posts: 6,339
|
Re: Acetylene regulator
Are you forgetting the Kidde recall! Just because it's made in the US does not mean it's good.
__________________
I know the voices aren't real but damn they have some good ideas! Last edited by redmodelt; 03-20-2018 at 06:22 PM. |
03-20-2018, 11:26 AM | #10 |
Member
Join Date: Sep 2017
Location: Costa Mesa, CA
Posts: 49
|
Re: Acetylene regulator
Craigslist is my go to. Just checked my area and you can get what you need for 25 to 65 bucks. Welding or tank suppliers may have some for cheap
|
03-20-2018, 06:06 PM | #11 |
Senior Member
Join Date: May 2010
Location: Mpls, MN
Posts: 27,582
|
Re: Acetylene regulator
Single stage will work fine for most of us. The last pair of tanks I got both had leaking valves, and I lost well over $100 worth of gas in one month. I only got to use my torch for about 10 minutes. I never went back, and have since learned that welding shop is now out of business. Screwed again.
|
03-20-2018, 06:27 PM | #12 |
Senior Member
Join Date: Dec 2010
Location: FRESNO, CA
Posts: 12,560
|
Re: Acetylene regulator
Probably just needs a new Diaphragm! (CHEAP!)
Bill Fixit
__________________
"THE ASSISTANT GURU OF STUFF" |
03-20-2018, 06:50 PM | #13 |
Senior Member
Join Date: May 2010
Location: Auburn Washington
Posts: 2,550
|
Re: Acetylene regulator
Gauges are cheap compared to the cost of acetylene over time. if they do not work correctly or leak. buy good gauges, they will save you money in the long run and last for years.
|
03-20-2018, 07:16 PM | #14 |
Senior Member
Join Date: May 2010
Location: Santee Calif.
Posts: 491
|
Re: Acetylene regulator
Check with your local welding supply shop about getting rebuilt, might be less $ than you think
|
03-20-2018, 07:38 PM | #15 |
Senior Member
Join Date: May 2010
Location: Lakeville, MN
Posts: 5,159
|
Re: Acetylene regulator
I checked with my local welding supply shop today. The fellow there said he could check the regulator with soapy water and see if it leaks. I am pretty sure it does, however it would be nice to know for sure. I think I may have lost some acetylene due to the leak. He said it was $70 to get the regulator repaired. The concern I have is, this is the third time I have had problem with the USA made acetylene regulator. The oxygen regulator has never had a problem.
Rusty Nelson |
03-20-2018, 08:23 PM | #16 |
Senior Member
Join Date: May 2010
Location: So Minn
Posts: 1,564
|
Re: Acetylene regulator
Get a repair kit. Fix it yourself for $20. That is what I did and the regulator works fine now. Here is a link to Amazon but you can just do a Google search and come up with more parts suppliers.
https://www.amazon.com/s/?ie=UTF8&ke...l_6h2p7o49ny_b |
03-20-2018, 08:37 PM | #17 |
Senior Member
Join Date: May 2010
Location: Epping N.H.
Posts: 2,969
|
Re: Acetylene regulator
I've had some problems with leaky tank valves lately.I could smell a little gas when the tanks were on,so I thought I had a regulator going bad.Sprayed tire soap on it and found the valve was weeping around the stem when open.It happened on two fresh tanks.Gas has gotten expensive.Acetylene-$148.Oxy_$68.70-30 argon mix-$111. When I got my first set of torches oxy was $8.and acetylene was $12.I also was making $1.60 an hour.
|
03-20-2018, 11:32 PM | #18 |
Senior Member
|
Re: Acetylene regulator
Always back the adjustment it will help get a longer life out of the diaphragm which might be the only thing wrong with it. Take it apart and check the diaphragm for cracks. I have made diaphragms for my air regulators which are about the same thing from brass shim stock. I have seen plastic diaphragm's in regulators but all of mine have brass ones. I even made one out of a Gal thinner can a couple of times.
|
03-21-2018, 06:03 AM | #19 |
Senior Member
Join Date: Jun 2014
Location: Westlake, ohio
Posts: 107
|
Re: Acetylene regulator
I had mine rebuilt at welding store for less then 100.
|
03-28-2018, 09:14 PM | #20 |
Member
Join Date: Dec 2017
Location: Fenton Michigan
Posts: 43
|
Re: Acetylene regulator
Rebuild it yourself, Easy, cheaper than having it done, and Victor parts are available
https://www.youtube.com/watch?v=POU7Zc8ONOM |
Thread Tools | |
Display Modes | |
|
|
Sponsored Links (Register now to hide all advertisements) |
|