The Ford Barn

vernon · 09-14-2018, 09:28 PM

Hello guys,
Just install a Tatterfiels manifold with a Stromberg 97 carb. I now need a bell crank. Is there one being made.

CarlG · 09-15-2018, 12:20 AM

My engine builder made and installed mine. (Optional at extra cost, of course. )

vernon · 09-15-2018, 06:34 AM

Thank you Carig. I saw a die cast on e-bay but can't seem to fine it now.

Pictures of yours would be helpful.

Charlie Stephens · 09-15-2018, 09:29 AM

Is this what you are looking for: https://www.fordbarn.com/forum/showt...ge#post1628897

Charlie Stephens

Bob C · 09-15-2018, 10:29 AM

Here's a picture of one that was on Epay.

Bob

Jim Brierley · 09-15-2018, 10:35 AM

Sponsored Links (Register now to hide all advertisements)

One can be easily made from aluminum or steel stock. There is no need to have an angle in it as pictured above. Make it longer than needed so you can adjust the length from the pivot point to suit your needs and be certain the carb fully opens.

vernon · 09-16-2018, 09:39 PM

Thanks to all for suggestion. problem making one is the throttle ball .I have look all over for them with no results. Any suggestions?

Bob C · 09-16-2018, 10:06 PM

No problem. http://www.carburetor-parts.com/Ball-Stud_c_1018.html
https://www.ebay.com/sch/i.html?LH_C...udlo=&_fosrp=1

Bob

vernon · 09-16-2018, 11:21 PM

Thank you Bob Just what I need

09-14-2018, 09:28 PM	#1
vernon Junior Member Join Date: Feb 2015 Posts: 21	bellcrank Hello guys, Just install a Tatterfiels manifold with a Stromberg 97 carb. I now need a bell crank. Is there one being made.

09-15-2018, 12:20 AM	#2
CarlG Senior Member Join Date: Nov 2010 Location: Anchorage, Alaska Posts: 9,115	Re: bellcrank My engine builder made and installed mine. (Optional at extra cost, of course. ) __________________ Alaskan A's Antique Auto Mushers of Alaska Model A Ford Club of America Model A Restorers Club Antique Automobile Club of America Mullins Owner's Club

09-15-2018, 06:34 AM	#3
vernon Junior Member Join Date: Feb 2015 Posts: 21	Re: bellcrank Thank you Carig. I saw a die cast on e-bay but can't seem to fine it now. Pictures of yours would be helpful.

09-15-2018, 09:29 AM	#4
Charlie Stephens Senior Member Join Date: May 2010 Location: Southern California Posts: 7,031	Re: bellcrank Is this what you are looking for: https://www.fordbarn.com/forum/showt...ge#post1628897 Charlie Stephens

09-15-2018, 10:35 AM	#6
Jim Brierley Senior Member Join Date: Jun 2010 Location: Temecula, CA Posts: 4,087	Re: bellcrank Sponsored Links (Register now to hide all advertisements) One can be easily made from aluminum or steel stock. There is no need to have an angle in it as pictured above. Make it longer than needed so you can adjust the length from the pivot point to suit your needs and be certain the carb fully opens.

09-16-2018, 09:39 PM	#7
vernon Junior Member Join Date: Feb 2015 Posts: 21	Re: bellcrank Thanks to all for suggestion. problem making one is the throttle ball .I have look all over for them with no results. Any suggestions?

09-16-2018, 10:06 PM	#8
Bob C Senior Member Join Date: May 2010 Location: So Cal Posts: 8,747	Re: bellcrank No problem. http://www.carburetor-parts.com/Ball-Stud_c_1018.html https://www.ebay.com/sch/i.html?LH_C...udlo=&_fosrp=1 Bob

09-16-2018, 11:21 PM	#9
vernon Junior Member Join Date: Feb 2015 Posts: 21	Re: bellcrank Thank you Bob Just what I need