Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 12-02-2019, 05:48 PM   #1
Russ/40
Senior Member
 
Russ/40's Avatar
 
Join Date: May 2010
Location: Santee, California
Posts: 3,505
Default That "Opportunity Knocks" Engine

It's back, the disastrous opportunity I couldn't pass up.

Sent the block to have it cleaned and Mag'd because it looked so good on top end. Well it failed me again, but, not so bad. Attached photos of the crack found. Now from every other crack I've seen posted here, it looks like a perfect candidate for the JB Weld approach. Not being a pressurized system, and it looks to be away from being a fatal crack. What say there barners? What would you do?
Attached Images
File Type: jpg model A.jpg (55.4 KB, 219 views)
File Type: jpg model a close-up.jpg (63.2 KB, 252 views)
Russ/40 is offline   Reply With Quote
Old 12-02-2019, 05:59 PM   #2
Mike Peters
Senior Member
 
Mike Peters's Avatar
 
Join Date: Aug 2012
Location: South East Wisconsin
Posts: 1,279
Default Re: That "Opportunity Knocks" Engine

You could JB weld that crack, put the engine back together, and run it on a test stand to see if it still leaks. If it still leaks, then you won't be out all that much time.
Mike Peters is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 12-02-2019, 06:15 PM   #3
butch chase
Junior Member
 
Join Date: Feb 2019
Location: Polk County Mssouri
Posts: 3
Default Re: That "Opportunity Knocks" Engine

A better approach is to clean well and sweat solder the crack full with TIN.



a local shop, Means Garage, does that with great success.
butch chase is offline   Reply With Quote
Old 12-02-2019, 06:58 PM   #4
Gary WA
Senior Member
 
Gary WA's Avatar
 
Join Date: May 2010
Location: Clinton,WA/Whidbey Island
Posts: 4,088
Default Re: That "Opportunity Knocks" Engine

Have it properly welded! You'll sleep better!
Attached Images
File Type: jpg walter dripping nose.jpg (19.0 KB, 11 views)
__________________
www.whidbeymodelaclub.com
Gary WA is offline   Reply With Quote
Old 12-02-2019, 07:37 PM   #5
CWPASADENA
Senior Member
 
CWPASADENA's Avatar
 
Join Date: May 2010
Location: PASADENA, CA
Posts: 1,881
Default Re: That "Opportunity Knocks" Engine

This crack is probably a result of the water in the engine freezing. This is not uncommon.


The first Model A engine I rebuilt back in the 1950's had a freeze crack in the same place. I had it pinned and that was considered a permanent repair. It never caused a problem.


I would think that JB Weld may be considered a temporary repair.


If you do use JB Weld, I would be sure the surface you are applying it to is CLEAN BRIGHT METAL, I would use a rotary file small grinder to prep the area.


I would not want to use anything that involved heat. This is not a high stress area, it is just the bottom of the water jacket.


JMO,


Chris W.
CWPASADENA is offline   Reply With Quote
Old 12-02-2019, 07:41 PM   #6
J Franklin
Senior Member
 
J Franklin's Avatar
 
Join Date: May 2010
Location: Oregon
Posts: 5,946
Default Re: That "Opportunity Knocks" Engine

Sponsored Links (Register now to hide all advertisements)
Shoot, that's why they invented BARRS STOP LEAK! Well, I do like the idea of solder, since it really is just a plumbing job anyway.
J Franklin is offline   Reply With Quote
Old 12-02-2019, 07:49 PM   #7
kenparker
Senior Member
 
kenparker's Avatar
 
Join Date: May 2010
Location: Van, Texas
Posts: 1,122
Default Re: That "Opportunity Knocks" Engine

Sweat solder is not that difficult. Just tedious and time consuming, but very pernament. Done it twice. works great. kp
kenparker is offline   Reply With Quote
Old 12-02-2019, 08:07 PM   #8
Jeff/Illinois
Senior Member
 
Jeff/Illinois's Avatar
 
Join Date: May 2010
Posts: 2,787
Default Re: That "Opportunity Knocks" Engine

I'm no fan of JB weld that stuff never worked for me.

Do it right have it pinned and welded up. A good machine shop can help you.

I know of a Model A engine rebuilder that did the JB weld magic on an acquaintance's motor. Twice. Two different motors.

He had taken his GOOD block to be rebuilt, and the guy gave him a POS engine in return, his good engine was sent off to somebody else probably the guy's buddy. The motors he got back were cracked just like this one. He was furious wanted his original motor back and it was 'alledgedly' long-gone.

Makes Terry Burtz' project look better all the time, the newly mfg. blocks. Ours are pushing a hundred years old.
Jeff/Illinois is offline   Reply With Quote
Old 12-02-2019, 08:23 PM   #9
Synchro909
Senior Member
 
Synchro909's Avatar
 
Join Date: Jun 2014
Location: Melbourne, Australia
Posts: 7,471
Default Re: That "Opportunity Knocks" Engine

Quote:
Originally Posted by Jeff/Illinois View Post
I'm no fan of JB weld that stuff never worked for me.

Do it right have it pinned and welded up. A good machine shop can help you.

I know of a Model A engine rebuilder that did the JB weld magic on an acquaintance's motor. Twice. Two different motors.

He had taken his GOOD block to be rebuilt, and the guy gave him a POS engine in return, his good engine was sent off to somebody else probably the guy's buddy. The motors he got back were cracked just like this one. He was furious wanted his original motor back and it was 'alledgedly' long-gone.

Makes Terry Burtz' project look better all the time, the newly mfg. blocks. Ours are pushing a hundred years old.
I've heard of dud blocks being substituted for good ones by engine rebuilders. I insist in the same engine back again. I note the number and make sure the rebuilder knows I have the number. I also (maybe I'm being paranoid) make a mark somewhere else that I look for later. Last one was a centre punch mark filed flat again at the water inlet. No one would notice and it makes no difference to the block later.
As for that crack, I'd clean around it and give it a bit of a vee, then use RTV. RTV will remain flexible, unlike an epoxy like JB and with heating and cooling happening (hopefully) many many times, I fear JB will eventually give up - not that it couldn't be reapplied.
__________________
I'm part of the only ever generation with an analogue childhood and a digital adulthood.
Synchro909 is offline   Reply With Quote
Old 12-02-2019, 08:24 PM   #10
Conaway2
Senior Member
 
Conaway2's Avatar
 
Join Date: Apr 2019
Location: Mt. Pleasant, SC
Posts: 601
Default Re: That "Opportunity Knocks" Engine

A JB weld repair does not last....I know.....soldering the crack is the way to go.
Conaway2 is offline   Reply With Quote
Old 12-02-2019, 10:01 PM   #11
w.michael
Senior Member
 
w.michael's Avatar
 
Join Date: May 2010
Location: North Carolina
Posts: 417
Default Re: That "Opportunity Knocks" Engine

I ran an engine for many years with a crack in that same location. Never did anything to it. It just oozed a bit, but never leaked enough to drip. Lasted until I knocked the center main out by lugging the engine. The crack never caused a problem.

W. Michael
w.michael is offline   Reply With Quote
Old 12-03-2019, 01:02 AM   #12
Russ/40
Senior Member
 
Russ/40's Avatar
 
Join Date: May 2010
Location: Santee, California
Posts: 3,505
Default Re: That "Opportunity Knocks" Engine

Of the responses, I'm mostly leaning toward soldering the crack, as whatever is done will be done by me. What soldering techniques are you suggesting? Brazing, Silver soldering or? The crack does leak when the block is filled with water. You can see the crack as a rust line. Will solder wick into the crack when rusted?
Might try stitching, as the area is so accessable.
Russ/40 is offline   Reply With Quote
Old 12-03-2019, 02:03 AM   #13
Bill G
Senior Member
 
Bill G's Avatar
 
Join Date: Jun 2017
Location: Walla Walla, WA
Posts: 1,044
Default Re: That "Opportunity Knocks" Engine

Solder will not adhere to rust, and JB probably won't either. If it were a clean crack, I would definitely prefer solder over JB.
Bill G is offline   Reply With Quote
Old 12-03-2019, 02:12 AM   #14
Russ/40
Senior Member
 
Russ/40's Avatar
 
Join Date: May 2010
Location: Santee, California
Posts: 3,505
Default Re: That "Opportunity Knocks" Engine

Anyone tried this stuff:
Attached Images
File Type: jpg sealer.JPG (18.2 KB, 90 views)
Russ/40 is offline   Reply With Quote
Old 12-12-2019, 06:47 AM   #15
Gerald1961
Member
 
Gerald1961's Avatar
 
Join Date: Dec 2013
Location: Germany
Posts: 59
Default Re: That "Opportunity Knocks" Engine

I am running my engine since more than 10000 mls with a JBwelded crack similar to yours. Important is to really find the ends of the crack; they ofte are nor really good visible. Clean the surface and widen the glue bed to ca. 1/8 or a bit less by grinding the surface with a dremel or so. Then in canīt go wrong.

Good luck!
Gerald1961 is offline   Reply With Quote
Old 12-12-2019, 08:56 AM   #16
marko39
Senior Member
 
Join Date: Oct 2016
Location: harpursville ny
Posts: 1,038
Default Re: That "Opportunity Knocks" Engine

If you are going to use JB weld something similar but better is Devcon.I used it to repair a rusted air compressor tank on my old Kellog compressor and that holds 175 psi. Been over 5years and still good.
marko39 is offline   Reply With Quote
Old 12-12-2019, 08:59 AM   #17
rocket1
Senior Member
 
Join Date: Mar 2014
Location: Midland Park,N.J.
Posts: 1,108
Default Re: That "Opportunity Knocks" Engine

You could always look for another block,talked to a guy in Hershey flea market who had a slew of motors and blocks he was getting rid of,I did not want to drive the 350 miles round trip to pick them up,maybe should have in retrospect.
rocket1 is offline   Reply With Quote
Old 12-12-2019, 09:31 AM   #18
J and M Machine
Senior Member
 
Join Date: Oct 2010
Location: 40 Mt.Vickery Rd. Southborough,MA 508-460-0733
Posts: 352
Default Re: That "Opportunity Knocks" Engine

Quote:
Originally Posted by Russ/40 View Post
It's back, the disastrous opportunity I couldn't pass up.

Sent the block to have it cleaned and Mag'd because it looked so good on top end. Well it failed me again, but, not so bad. Attached photos of the crack found. Now from every other crack I've seen posted here, it looks like a perfect candidate for the JB Weld approach. Not being a pressurized system, and it looks to be away from being a fatal crack. What say there barners? What would you do?
It is far from a fatal crack but one that will keep growing if not repaired properly. It's common for Model A' engines to crack in that spot.
I would also recommend pressure testing as there is a casting wire right above your crack that will also leak water as well. If you look close you see a small circle. This will leak also. To fix it permenantly, take it to Lock n stitch or someone who can do metal stitching properly.
I have provided examples of the before and after of the same crack in same location.

http://www.jandm-machine.com/metalStitching.html
Attached Images
File Type: jpg IMG_3468.JPG (52.8 KB, 96 views)
File Type: jpg IMG_7917.JPG (53.5 KB, 99 views)
J and M Machine is offline   Reply With Quote
Old 12-12-2019, 03:54 PM   #19
SAJ
Senior Member
 
SAJ's Avatar
 
Join Date: Jul 2010
Location: Auckland, New Zealand
Posts: 513
Default Re: That "Opportunity Knocks" Engine

Beautiful work J and M!
Is the small circle visible in your photo or does one have to look at a real block with a loupe eyepiece? Is the circle the END of the casting wire and therefore very small? I am interested to know what to look for.
SAJ in NZ
SAJ is offline   Reply With Quote
Old 12-12-2019, 04:34 PM   #20
Russ/40
Senior Member
 
Russ/40's Avatar
 
Join Date: May 2010
Location: Santee, California
Posts: 3,505
Default Re: That "Opportunity Knocks" Engine

Quote:
Originally Posted by SAJ View Post
Beautiful work J and M!
Is the small circle visible in your photo or does one have to look at a real block with a loupe eyepiece? Is the circle the END of the casting wire and therefore very small? I am interested to know what to look for.
SAJ in NZ
If you look at my photo in post #1, you can see it about center above the crack.
Russ/40 is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 09:17 AM.