Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 03-24-2023, 09:28 AM   #1
jtucker
Junior Member
 
Join Date: Nov 2014
Location: Roseville, MN
Posts: 25
Default Clutch Question

Is the throwout bearing press fit to the hub? Or do I just have some 80 year old grease that make the bearing feel like it is press fit?

Thanks for any help.
Jim
jtucker is offline   Reply With Quote
Old 03-24-2023, 10:46 AM   #2
katy
Senior Member
 
katy's Avatar
 
Join Date: Jun 2015
Location: Red Deer, Alberta
Posts: 4,722
Default Re: Clutch Question

IIRC it'a light press fit.
__________________
If you don't hear a rumor by 10 AM, start one!.
Got my education out behind the barn!
katy is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 03-24-2023, 05:20 PM   #3
Marshall V. Daut
Senior Member
 
Join Date: Apr 2011
Location: Davenport, Iowa
Posts: 1,782
Default Re: Clutch Question

There are two easy and safe ways (for the bearing) that I have used for years without losing the patient during the operation.
(1) Open a vise's jaws so that the bearing's inner sleeve will just be supported on either side of the vise. Do not open the jaws any wider than that or else the bearing will be distorted during the next steps! Place the open crimped face of the throwout bearing up so that any escaping grease does not fling forward and get onto the pressure plate's face. With the throwout bearing oriented that way and the sleeve's edges supported by the vise's jaws, place the collar inside the bearing from the top, ensuring it starts straight. Place a wooden block across the top of the collar and use a hammer to drive the collar down through the bearing's inner sleeve, checking during the first few downward movements that the collar is going down straight. The wooden block will absorb the hammer blows so that the edges of the collar don't get distorted. Once the sleeve has been started and is lined up straight, then you can hammer the sleeve home via the wooden block. You will feel when the collar seats against the bearing's inner sleeve. Spin the bearing afterwards with your fingers to ensure it doesn't bind. It should have some resistance. If it spins freely like a roller bearing, it's no good. If you can't spin it at all or if the resistance is too much, the bearing is probably bent.
(2) Or, place the bearing with the correct orientation (open side up) over the collar in a vertical position, ensuring it sits straight. Slightly tap the edges of the collar to begin its downward movement. Not much, just enough so that the collar doesn't fall out when the assembly is turned horizontally. With the vise's jaws open as wide as necessary, place the two pieces between the jaws and begin turning the vise's handle, slowly at first to ensure the collar goes in straight. Once you're sure it is doing so, then you can crank the collar home until it seats against the throwout bearing's inner sleeve.
Because over the years I have had to do this with smaller vises that don't open far enough, I prefer method #1. That works any place, no matter what the vise's size. It just needs to open wide enough to support the throwout bearing's inner sleeve edges.
Marshall

Last edited by Marshall V. Daut; 03-24-2023 at 06:00 PM.
Marshall V. Daut is offline   Reply With Quote
Old 03-25-2023, 07:27 PM   #4
Gene F
Senior Member
 
Gene F's Avatar
 
Join Date: Mar 2012
Location: Ohio
Posts: 1,384
Default Re: Clutch Question

Sponsored Links (Register now to hide all advertisements)
I tend to use the handle method with plywood over the jaw.
Gene F is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 10:06 AM.