Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 11-26-2019, 09:02 AM   #1
Merc Cruzer
Senior Member
 
Merc Cruzer's Avatar
 
Join Date: Jul 2010
Location: Conifer, Colorado
Posts: 2,420
Default Decarbonize engine

I have recently corrected an extended issue of an over rich carburetor. Now I would like to decarbonize the engine. I was watched videos of using water down the carb (steam) and Seafoam (hotsoak).

What has been your experience with either or both? If you used Seafoam, how long did you let it hotsoak? Do you need to do this more than once? Does it really work, or do I need to remove the heads?

Thank you.
Merc Cruzer is offline   Reply With Quote
Old 11-26-2019, 09:08 AM   #2
alanwoodieman
Senior Member
 
Join Date: May 2010
Location: upstate SC
Posts: 2,962
Default Re: Decarbonize engine

spray of water down the carb throat of a warm, running engine has always worked for me-run the engine about 1500 rpms
alanwoodieman is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 11-26-2019, 12:17 PM   #3
scicala
Senior Member
 
scicala's Avatar
 
Join Date: Jun 2010
Location: Detroit suburb, MI
Posts: 3,697
Default Re: Decarbonize engine

Quote:
Originally Posted by alanwoodieman View Post
spray of water down the carb throat of a warm, running engine has always worked for me-run the engine about 1500 rpms




I've used this method a few times. Seems to steam clean the combustion chambers. I used to refer to it as a tune up in a glass.


Sal
scicala is offline   Reply With Quote
Old 11-26-2019, 01:26 PM   #4
J Franklin
Senior Member
 
J Franklin's Avatar
 
Join Date: May 2010
Location: Oregon
Posts: 5,946
Default Re: Decarbonize engine

Quote:
Originally Posted by scicala View Post
I've used this method a few times. Seems to steam clean the combustion chambers. I used to refer to it as a tune up in a glass.


Sal
I wouldn't use cold water on a very warm engine, as things crack when shocked.
I was taught this method in auto shop class and a spray was used during fast idle on a slightly warm engine until there was stalling. instructed to leave overnight and then make sure nothing or no-one was standing behind the car when it was restarted the next day! The instructor was an old time mechanic with old time ideas, but they worked.
J Franklin is offline   Reply With Quote
Old 11-26-2019, 09:09 AM   #5
Jack E/NJ
Senior Member
 
Jack E/NJ's Avatar
 
Join Date: May 2010
Posts: 2,171
Default Re: Decarbonize engine

Drive it. Jack E/NJ
Jack E/NJ is offline   Reply With Quote
Old 11-26-2019, 09:21 AM   #6
RalphM
Senior Member
 
RalphM's Avatar
 
Join Date: Nov 2015
Location: North Pole, Alaska
Posts: 2,646
Default Re: Decarbonize engine

Sponsored Links (Register now to hide all advertisements)
If you have ever pulled the head on an engine that is leaking coolant into one or more cylinders(and still running) you will find that the coolant cleans the piston, valves and head like new.
My vote is for water mist.
RalphM is offline   Reply With Quote
Old 11-26-2019, 10:21 AM   #7
Desoto291Hemi
Senior Member
 
Join Date: Oct 2019
Location: Carthage , Tennessee
Posts: 199
Default Re: Decarbonize engine

Woodieman is correct. That will work great.

Tommy
Desoto291Hemi is offline   Reply With Quote
Old 11-26-2019, 10:36 AM   #8
Merc Cruzer
Senior Member
 
Merc Cruzer's Avatar
 
Join Date: Jul 2010
Location: Conifer, Colorado
Posts: 2,420
Default Re: Decarbonize engine

Thanks guys. Awhile back I bought a bore scope that hooks to my phone. It is not great but from the images I could get, the top of the pistons don't look too bad. At least not as bad as I would have thought.

I will work on this further today to get better/clearer pictures. It is not real good too close up.
Attached Images
File Type: jpg 191126_080908.jpg (182.0 KB, 27 views)
File Type: jpg 191126_080945.jpg (181.8 KB, 22 views)
File Type: jpg 191126_081044.jpg (178.7 KB, 23 views)
File Type: jpg 191126_081046.jpg (178.1 KB, 17 views)
File Type: jpg 191126_081051.jpg (175.8 KB, 14 views)
Merc Cruzer is offline   Reply With Quote
Old 11-26-2019, 11:26 AM   #9
drolston
Senior Member
 
drolston's Avatar
 
Join Date: Jun 2014
Location: Williamsburg, VA
Posts: 1,622
Default Re: Decarbonize engine

Back in the olden days we would slowly pour kerosene into the carb while jazzing the throttle to keep it from stalling. The pistons and chamber stayed pretty clean. I don't know whether it was the kerosene treatments or the fact that I ran the p__s out of that engine.
drolston is offline   Reply With Quote
Old 11-26-2019, 12:06 PM   #10
Merc Cruzer
Senior Member
 
Merc Cruzer's Avatar
 
Join Date: Jul 2010
Location: Conifer, Colorado
Posts: 2,420
Default Re: Decarbonize engine

Every time I come back from Denver, I have to climb over 3,000 ft in 13 miles. The gas pedal spends most of its time pretty close to the floor. The drive in itself is probably self cleaning.
Merc Cruzer is offline   Reply With Quote
Old 11-26-2019, 07:15 PM   #11
Jack E/NJ
Senior Member
 
Jack E/NJ's Avatar
 
Join Date: May 2010
Posts: 2,171
Default Re: Decarbonize engine

>>>pistons don't look too bad. At least not as bad as I would have thought.>>>
>>>The drive in itself is probably self cleaning.>>>


Agreed. 8^) Jack E/NJ
Jack E/NJ is offline   Reply With Quote
Old 11-26-2019, 07:31 PM   #12
tubman
Senior Member
 
tubman's Avatar
 
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,259
Default Re: Decarbonize engine

In the fifties, my old man always bought Olds 88's with the top engine. On highway trips, he would occasionally accelerate to almost 100 (he sometimes made it if the straightaway was long enough). He said he was "blowing the carbon out". I don't really think that it was all about that.
tubman is offline   Reply With Quote
Old 11-26-2019, 08:09 PM   #13
mfirth
Senior Member
 
Join Date: Aug 2017
Location: ohio
Posts: 986
Default Re: Decarbonize engine

Tubman, my dad had Packards till 1958 when he bought a Lincoln same story. His last Packard was a 56 Carribian & i don't think it ever had time to "carbon up". Those 2 4's were open a lot..........a real car!
mike
mfirth is offline   Reply With Quote
Old 11-26-2019, 08:07 PM   #14
A bones
Senior Member
 
A bones's Avatar
 
Join Date: May 2010
Location: CLAYTON DE
Posts: 1,280
Default Re: Decarbonize engine

Hey J. Franklin Spray or mist is the key. The temp will take care of itself. Just don't overwater. Hydraulic lock is a very painful experience
__________________
Enjoy yer day. Tom
Hate can't fix what it started.
A bones is offline   Reply With Quote
Old 11-26-2019, 09:31 PM   #15
Jack E/NJ
Senior Member
 
Jack E/NJ's Avatar
 
Join Date: May 2010
Posts: 2,171
Default Re: Decarbonize engine

tubman>>>He said he was "blowing the carbon out". I don't really think that it was all about that.>>>


True. Not all. It must be fun too. Jack E/NJ
Jack E/NJ is offline   Reply With Quote
Old 11-27-2019, 09:08 AM   #16
Gene1949
Senior Member
 
Gene1949's Avatar
 
Join Date: Jun 2016
Location: Pahrump, NV
Posts: 372
Default Re: Decarbonize engine

Dad was never wrong
I "blow the carbon out" whenever I get the chance
Gene1949 is offline   Reply With Quote
Old 11-27-2019, 10:24 AM   #17
outlaw
Senior Member
 
Join Date: May 2010
Location: Eagle River,Alaska
Posts: 352
Default Re: Decarbonize engine

My dad always used diesel fuel. He would slowly pour it down the carb at a about 1500 rpm. When the motor would start to lug down he would back off until it would pick up again, then increase the amount of diesel till it started lugging again & repeat. It would smoke up the neighbor hood & stink like hell. One time someone called the fire dept cause they thought a house was on fire. Two engines showed up lights & sirens wailing!
outlaw is offline   Reply With Quote
Old 11-27-2019, 10:42 AM   #18
40 Deluxe
Senior Member
 
Join Date: May 2010
Location: now Kuna, Idaho
Posts: 3,774
Default Re: Decarbonize engine

Quote:
Originally Posted by outlaw View Post
My dad always used diesel fuel. He would slowly pour it down the carb at a about 1500 rpm. When the motor would start to lug down he would back off until it would pick up again, then increase the amount of diesel till it started lugging again & repeat. It would smoke up the neighbor hood & stink like hell. One time someone called the fire dept cause they thought a house was on fire. Two engines showed up lights & sirens wailing!
He was more likely adding carbon, not removing it!
40 Deluxe is offline   Reply With Quote
Old 11-27-2019, 12:22 PM   #19
Jack E/NJ
Senior Member
 
Jack E/NJ's Avatar
 
Join Date: May 2010
Posts: 2,171
Default Re: Decarbonize engine

>>>He was more likely adding carbon, not removing it!>>>


Of course. This is another fun part. Technically known as rolling coal to the diesel fuel cognoscenti. 8^) Jack E/NJ
Jack E/NJ is offline   Reply With Quote
Old 11-27-2019, 04:04 PM   #20
jrvariel48
Senior Member
 
jrvariel48's Avatar
 
Join Date: Jan 2012
Location: New Jersey
Posts: 1,423
Default Re: Decarbonize engine

Can this be done with a supercharger on the motor??
jrvariel48 is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 01:28 AM.