Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 08-02-2016, 06:40 PM   #21
Newc
Senior Member
 
Newc's Avatar
 
Join Date: May 2010
Posts: 2,458
Default Re: 1940 Flathead - Dual Groove Crank Pulley???

H iall; Remember there are those WW2 military engs. Newc
Newc is offline   Reply With Quote
Old 08-04-2016, 04:46 PM   #22
Bob C
Senior Member
 
Join Date: May 2010
Location: So Cal
Posts: 8,711
Default Re: 1940 Flathead - Dual Groove Crank Pulley???

It doesn't have the fan mount.

Bob
Bob C is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 08-08-2016, 05:55 PM   #23
Brian
Senior Member
 
Brian's Avatar
 
Join Date: May 2010
Location: Masterton, New Zealand
Posts: 3,816
Default Re: 1940 Flathead - Dual Groove Crank Pulley???

i have previously posted on this thread and stated I'd owned one of these pulleys and given it to a fellow in USA who needed it for a supercharger application. I wrote him on a different forum and below is his response, which gives part numbers etc. Quite helpful;


Hi Brian, I don't get to this site too often but when I do, for some reason, I didn't notice the PM alert.
So that is why I haven't answered your PM. My apology for not responding sooner.
I do go on the "Barn" almost daily and I have been following that thread. I tried a couple of times to post a picture but that ability seems to come and go with me. My pictures are stored on my laptop but it looks like the "Barn" needs something from a storage site. At least that's the way it looks to me. Anyway, the pictures that were posted do indicate the existence of that pulley which you and I know of and have seen. My Ford Chassis Parts Manual (aka, the green bible) for 1938-39-40-41 exclusively, shows that part as:
09B 6312-A [pulley-crankshaft (except DSR bus)]; Model 09B,19B for the years 1940 and 1941. Or
09B 6312-B [pulley-crankshaft (DSR bus only)]; Model 19B for 1941 only. I have no clue what a DSR bus is. The pulley that you gave me is 09B 6312 A1C or G, I can't make out the last digit . It does however, line up with the water pump and blower pulleys which is the important part.
I still have your e-mail address and I'll try so send you some of the pictures of my McCulloch.
I hope you and yours are well and as always, many thanks for the pulley. Regards, Ken
__________________
Unfortunately, two half wits don't make a whole wit!
Brian is offline   Reply With Quote
Old 08-08-2016, 07:08 PM   #24
V8COOPMAN
Senior Member
 
V8COOPMAN's Avatar
 
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,106
Default Re: 1940 Flathead - Dual Groove Crank Pulley???

"DSR bus".......Detroit Department of Street Railways (DSR). DD
__________________
Click Links Below __


'35-'36 W/8BA & MECHANICAL FAN


T5 W/TORQUE TUBE
V8COOPMAN is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 05:46 AM.