Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 10-28-2020, 12:40 PM   #1
adileo
Senior Member
 
adileo's Avatar
 
Join Date: Jun 2014
Location: New Jersey
Posts: 1,772
Default 52 F1 oil seal

Hi guys

Workin on replacing the oil seal. I’m having difficulty getting old one out & the part looks different than what’s up on truck. Is there a cap that covers oil seal? It’s not shown in shop manual.
Attached Images
File Type: jpeg 7319356A-2F98-4E0F-8F8B-433A40EE119C.jpeg (27.3 KB, 56 views)
File Type: jpg 675C77DF-1CCC-4EC2-BD3E-9BD7B3965858.jpg (43.0 KB, 39 views)
__________________
Thanks

Andy
1952 F1
adileo is offline   Reply With Quote
Old 10-28-2020, 01:20 PM   #2
51 MERC-CT
Senior Member
 
51 MERC-CT's Avatar
 
Join Date: May 2010
Location: East Hartford, Ct
Posts: 5,898
Default Re: 52 F1 oil seal

There are a few different oil seals, which one are you talkin' about?
__________________
DON'T RECALL DOING SOMETHING FOR MYSELF BASED ON SOMEONE ELSE'S LIKES OR DISLIKES
51 MERC-CT is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 10-28-2020, 01:52 PM   #3
adileo
Senior Member
 
adileo's Avatar
 
Join Date: Jun 2014
Location: New Jersey
Posts: 1,772
Default Re: 52 F1 oil seal

Thanks- The part number is M-4676.

Is there a deflector / cap over it? If yes is it presses on or screw in. See pic to left above.
__________________
Thanks

Andy
1952 F1
adileo is offline   Reply With Quote
Old 10-28-2020, 02:01 PM   #4
Bob C
Senior Member
 
Join Date: May 2010
Location: So Cal
Posts: 8,697
Default Re: 52 F1 oil seal

The shop manual doesn't show a deflector, just the seal and companion flange.
Bob C is offline   Reply With Quote
Old 10-28-2020, 02:06 PM   #5
adileo
Senior Member
 
adileo's Avatar
 
Join Date: Jun 2014
Location: New Jersey
Posts: 1,772
Default Re: 52 F1 oil seal

I know but maybe this rear was changed out. See pic it has a cap - deflector or something I can’t get off....
__________________
Thanks

Andy
1952 F1
adileo is offline   Reply With Quote
Old 10-28-2020, 02:19 PM   #6
alanwoodieman
Senior Member
 
Join Date: May 2010
Location: upstate SC
Posts: 2,962
Default Re: 52 F1 oil seal

Sponsored Links (Register now to hide all advertisements)
changed out mine on my 49 F1-new one looks just like yours
alanwoodieman is offline   Reply With Quote
Old 10-28-2020, 02:25 PM   #7
adileo
Senior Member
 
adileo's Avatar
 
Join Date: Jun 2014
Location: New Jersey
Posts: 1,772
Default Re: 52 F1 oil seal

How did get the plate or seal out?

Do I need the deflector if I destroy it getting it out?
__________________
Thanks

Andy
1952 F1

Last edited by adileo; 10-28-2020 at 03:43 PM.
adileo is offline   Reply With Quote
Old 10-28-2020, 03:47 PM   #8
alanwoodieman
Senior Member
 
Join Date: May 2010
Location: upstate SC
Posts: 2,962
Default Re: 52 F1 oil seal

drill two hole on opposite sides--run a large sheet metal screw in and pry out seal using the alternate holes. always remember the "edge" of the seal goes against the fluid side
alanwoodieman is offline   Reply With Quote
Old 10-28-2020, 03:53 PM   #9
Bob C
Senior Member
 
Join Date: May 2010
Location: So Cal
Posts: 8,697
Default Re: 52 F1 oil seal

What deflector? Are you asking about the oil slinger that's behind the seal?
Bob C is offline   Reply With Quote
Old 10-28-2020, 04:00 PM   #10
adileo
Senior Member
 
adileo's Avatar
 
Join Date: Jun 2014
Location: New Jersey
Posts: 1,772
Default Re: 52 F1 oil seal

No please see pic on left. It’s in front
__________________
Thanks

Andy
1952 F1
adileo is offline   Reply With Quote
Old 10-28-2020, 04:16 PM   #11
51 MERC-CT
Senior Member
 
51 MERC-CT's Avatar
 
Join Date: May 2010
Location: East Hartford, Ct
Posts: 5,898
Default Re: 52 F1 oil seal

Does the pic on left show the shield and bearing in place with the axle removed?
__________________
DON'T RECALL DOING SOMETHING FOR MYSELF BASED ON SOMEONE ELSE'S LIKES OR DISLIKES

Last edited by 51 MERC-CT; 10-28-2020 at 04:23 PM.
51 MERC-CT is offline   Reply With Quote
Old 10-28-2020, 04:20 PM   #12
adileo
Senior Member
 
adileo's Avatar
 
Join Date: Jun 2014
Location: New Jersey
Posts: 1,772
Default Re: 52 F1 oil seal

Hi no

The pic shows the view with drive shaft, companion flange & nut removed.
__________________
Thanks

Andy
1952 F1
adileo is offline   Reply With Quote
Old 10-28-2020, 04:35 PM   #13
51 MERC-CT
Senior Member
 
51 MERC-CT's Avatar
 
Join Date: May 2010
Location: East Hartford, Ct
Posts: 5,898
Default Re: 52 F1 oil seal

Quote:
Originally Posted by adileo View Post
Hi no

The pic shows the view with drive shaft, companion flange & nut removed.
This now becomes a little clearer (it's the pinion shaft seal not an axle seal)
It should pry off utilizing the outer seam.
Attached Images
File Type: jpg Flathead_Rear_Axle_1948-52pickup.jpg (101.3 KB, 27 views)
__________________
DON'T RECALL DOING SOMETHING FOR MYSELF BASED ON SOMEONE ELSE'S LIKES OR DISLIKES

Last edited by 51 MERC-CT; 10-28-2020 at 04:56 PM.
51 MERC-CT is offline   Reply With Quote
Old 10-28-2020, 04:51 PM   #14
adileo
Senior Member
 
adileo's Avatar
 
Join Date: Jun 2014
Location: New Jersey
Posts: 1,772
Default Re: 52 F1 oil seal

This from shop manual:
Attached Images
File Type: jpeg 5F921D6D-F476-4A31-A803-B1ED691E1164.jpeg (25.4 KB, 22 views)
__________________
Thanks

Andy
1952 F1
adileo is offline   Reply With Quote
Old 10-28-2020, 05:35 PM   #15
adileo
Senior Member
 
adileo's Avatar
 
Join Date: Jun 2014
Location: New Jersey
Posts: 1,772
Default Re: 52 F1 oil seal

Thanks all! It was confusing that the replacement didn’t look like what I was seeing on the truck. What I’ve gathered is the old original seal had a metal lip. The replacement doesn’t and it’s not needed. So I can now hack at it tomorrow.
__________________
Thanks

Andy
1952 F1
adileo is offline   Reply With Quote
Old 10-28-2020, 06:07 PM   #16
JSeery
Member Emeritus
 
JSeery's Avatar
 
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
Default Re: 52 F1 oil seal

Just remember you're messing with the pre-load on the pinion. Need to mark the nut well and be sure it gets back to the same location.
JSeery is offline   Reply With Quote
Old 10-28-2020, 06:23 PM   #17
adileo
Senior Member
 
adileo's Avatar
 
Join Date: Jun 2014
Location: New Jersey
Posts: 1,772
Default Re: 52 F1 oil seal

Jerry thanks. I didn’t mark it. The book says tork 140-180.

Two questions. Since I still haven’t removed the oil seal. Should I put the nut and yoke back tork and mark? Or too late and just tork to specs?
__________________
Thanks

Andy
1952 F1
adileo is offline   Reply With Quote
Old 10-28-2020, 06:46 PM   #18
JSeery
Member Emeritus
 
JSeery's Avatar
 
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
Default Re: 52 F1 oil seal

I think it's to late to correct it now. For future reference, always mark a pinion nut before you remove it. The torque spec is all you have to go on now, most likely will be ok.
JSeery is offline   Reply With Quote
Old 10-28-2020, 06:59 PM   #19
adileo
Senior Member
 
adileo's Avatar
 
Join Date: Jun 2014
Location: New Jersey
Posts: 1,772
Default Re: 52 F1 oil seal

Quote:
Originally Posted by JSeery View Post
I think it's to late to correct it now. For future reference, always mark a pinion nut before you remove it. The torque spec is all you have to go on now, most likely will be ok.
My bad. Thanks!
__________________
Thanks

Andy
1952 F1
adileo is offline   Reply With Quote
Old 10-28-2020, 08:23 PM   #20
Ross F-1
Senior Member
 
Ross F-1's Avatar
 
Join Date: Nov 2010
Location: NM
Posts: 2,438
Default Re: 52 F1 oil seal

I would absolutely go with torque to specs rather than the position the nut was in 68 yrs ago when it had brand new bearings. Although you may end up backing off to get the cotter pin in.
__________________
'52 F-1, EAB flathead
Ross F-1 is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 06:11 AM.