Go Back   The Ford Barn > General Discussion > Model T (1909-1927)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 08-17-2019, 01:09 PM   #1
Chris Haynes
Senior Member
 
Chris Haynes's Avatar
 
Join Date: May 2010
Location: Camarillo, CA and Pine Grove, CA
Posts: 2,830
Default High compression head question

I see ads for a 8 to 1 head. My question is how long will the Babbitted bearings survive?
__________________
1921 Runabout
1930 Tudor
Early 1930 AA
Speed costs money. How fast do you want to go?
Chris Haynes is offline   Reply With Quote
Old 08-17-2019, 01:29 PM   #2
J Franklin
Senior Member
 
J Franklin's Avatar
 
Join Date: May 2010
Location: Oregon
Posts: 5,947
Default Re: High compression head question

If you are racing, who cares!? Is that head designed to be used with poured bearings?
J Franklin is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 08-18-2019, 04:17 PM   #3
Dodge
Senior Member
 
Join Date: Nov 2011
Location: Sonoma, CA.
Posts: 1,491
Default Re: High compression head question

8 might be pushing it a bit. Go with one of the 6-1 Z heads they work great
Dodge is offline   Reply With Quote
Old 08-20-2019, 01:24 PM   #4
AzBob
Senior Member
 
Join Date: Oct 2018
Location: Prescott, AZ
Posts: 120
Default Re: High compression head question

I live in a hilly area at 5300 ft. elevation. Installed the Prus 8:1 head on my stock ’26 runabout last year. Best upgrade for the money. Like the ad says, “Flattens the hills”. A hill I had to previously drop down into low with I can now maintain 35 mph in high. No pinging and no concerns with babbit or crank (have EE crank). Over 1000 miles now.
AzBob is offline   Reply With Quote
Old 08-25-2019, 12:03 PM   #5
M2M
Senior Member
 
M2M's Avatar
 
Join Date: Jul 2012
Location: Australia/USA/EU/Soviet Russia
Posts: 1,105
Default Re: High compression head question

The P head IS NOT 8:1 or close; just because his ads say so doesn't make it true. It's still a good head, as is the Z head.
__________________

M2M is offline   Reply With Quote
Old 08-26-2019, 08:29 AM   #6
rotorwrench
Senior Member
 
rotorwrench's Avatar
 
Join Date: Jun 2010
Location: San Antonio, Texas
Posts: 16,371
Default Re: High compression head question

Sponsored Links (Register now to hide all advertisements)
With the necessary clearance for valves on the L-head designs, they would be hard pressed to get to 7.5:1. This is why folks came up with the OHV conversions back in the day and some of those still only had intake valves in the head.

Poured babbitt bearings can take as much rough housing as any but they are a lot harder to replace when they wear out.
rotorwrench is offline   Reply With Quote
Old 08-31-2019, 11:18 AM   #7
AzBob
Senior Member
 
Join Date: Oct 2018
Location: Prescott, AZ
Posts: 120
Default Re: High compression head question

I would like to see the data that proves the Prus head does not deliver the advertised 8:1 compression. I was assured by Mr. Prus himself that it indeed delivers 8:1.
AzBob is offline   Reply With Quote
Old 08-31-2019, 04:32 PM   #8
Royce P
Senior Member
 
Royce P's Avatar
 
Join Date: May 2010
Location: Tulsa OK
Posts: 476
Default Re: High compression head question

The math is quite simple. You need the volume of the combustion chamber with the piston at TDC. You need the volume of the combustion chamber + the cylinder's swept area with the piston at BDC. Add the two. Then divide the larger sum by the other.


Variables include type of piston and the bore size. Several capable folks have measured the cylinder head and done the math with results in the neighborhood of 6:1 ratio. If Mr. Prus says otherwise ask him to provide the math that he is using to come up with a different answer.


I personally have never seen one but hear nothing but good reviews of the product. If you think a high compression head is what you need then why not just buy one and try it?




Quote:
Originally Posted by AzBob View Post
I would like to see the data that proves the Prus head does not deliver the advertised 8:1 compression. I was assured by Mr. Prus himself that it indeed delivers 8:1.
__________________
1910 Touring
1914 Touring
1915 Touring
1917 Torpedo Runabout
Royce P is offline   Reply With Quote
Old 08-31-2019, 07:19 PM   #9
rotorwrench
Senior Member
 
rotorwrench's Avatar
 
Join Date: Jun 2010
Location: San Antonio, Texas
Posts: 16,371
Default Re: High compression head question

It's difficult to realize that high a compression ratio on any of the flathead designs let alone the Model T types. The OHV head was the most common way back in the day.

If you shave the head, there still has to be valve clearance. If you have higher valve lift with a race cam, it just makes things worse. The amount of compression possible is finite.
rotorwrench is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 09:09 PM.