Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 07-20-2017, 09:47 PM   #1
Strodder
Junior Member
 
Strodder's Avatar
 
Join Date: Jul 2017
Location: Hesperia Ca
Posts: 4
Default 16 spline Slip yoke

I converted a 40 3 speed to an open driveshaft. Now I need a 16 spline slip yoke. I know it's been asked before, but never found a good answer. What years should I look for? Or where can I buy a new one. Some of the places I looked on the net were confusing. Does anybody have a link I can go to, even if it's E-Bay.
Thanks in advance,
Dennis

Strodder is offline   Reply With Quote
Old 07-20-2017, 10:45 PM   #2
Newc
Senior Member
 
Newc's Avatar
 
Join Date: May 2010
Posts: 1,622
Default Re: 16 spline Slip yoke

H;i the original yokes are usually with the driveshafts,use a pressed in u joint. I have heard of a GM yoke that will work. the yoke is fixed by a bolt into the output shaft right? Others will jump in on this post. Newc
Newc is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 07-20-2017, 11:55 PM   #3
Art Newland
Senior Member
 
Art Newland's Avatar
 
Join Date: Mar 2016
Location: Lynden, WA
Posts: 1,556
Default Re: 16 spline Slip yoke

I just picked up a NOS yoke from "barnfind08", contact him and see if he has another.
Art Newland is offline   Reply With Quote
Old 07-21-2017, 12:38 AM   #4
34fivewindow
Senior Member
 
34fivewindow's Avatar
 
Join Date: May 2010
Location: Santa Rosa, Calif.
Posts: 321
Default Re: 16 spline Slip yoke

1955 to 61 GM cast iron powerglide yoke.
34fivewindow is offline   Reply With Quote
Old 07-21-2017, 09:07 AM   #5
V Clark
Member
 
Join Date: May 2010
Posts: 55
Default Re: 16 spline Slip yoke

55 chev. power glide yoke will work .. A little longer but can be trimmed . I think the original is about an 1" shorter. I can check my pile and look when I get out in the shop .. Not too hard to locate for you I would think. Van
V Clark is offline   Reply With Quote
Old 07-21-2017, 09:50 AM   #6
Strodder
Junior Member
 
Strodder's Avatar
 
Join Date: Jul 2017
Location: Hesperia Ca
Posts: 4
Default Re: 16 spline Slip yoke

Sponsored Links (Register now to hide all advertisements)
Thanks. Can you post a picture of it when you find it?
Strodder is offline   Reply With Quote
Old 07-21-2017, 11:19 AM   #7
rotorwrench
Senior Member
 
rotorwrench's Avatar
 
Join Date: Jun 2010
Location: San Antonio, Texas
Posts: 13,551
Default Re: 16 spline Slip yoke

The 21C-4841 was the first knuckle & plug (or slip yoke) for the open drive commercials and it was used from 1942 to 1952. It should be relatively common, especially when folks are swapping out the Dana Spicer stuff for something else.
rotorwrench is online now   Reply With Quote
Old 07-21-2017, 12:17 PM   #8
skidmarks
Senior Member
 
skidmarks's Avatar
 
Join Date: Aug 2010
Location: newark, delaware
Posts: 3,735
Default Re: 16 spline Slip yoke

I got one if your still looking. $45 shipped to your door. Its out of a 50 ford F1
skidmarks is offline   Reply With Quote
Old 06-12-2019, 12:37 PM   #9
alanp561
Junior Member
 
alanp561's Avatar
 
Join Date: Nov 2017
Location: Cleveland TN
Posts: 25
Default Re: 16 spline Slip yoke

Do you still have your 50 F1 16 spline slip yoke?
alanp561 is offline   Reply With Quote
Old 06-13-2019, 09:26 AM   #10
Strodder
Junior Member
 
Strodder's Avatar
 
Join Date: Jul 2017
Location: Hesperia Ca
Posts: 4
Default Re: 16 spline Slip yoke

Quote:
Originally Posted by alanp561 View Post
Do you still have your 50 F1 16 spline slip yoke?
Sorry, no
Strodder is offline   Reply With Quote
Old 06-14-2019, 03:21 AM   #11
tub1
Senior Member
 
tub1's Avatar
 
Join Date: May 2010
Location: tasmania
Posts: 221
Default Re: 16 spline Slip yoke

I think manual customline one fits
tub1 is offline   Reply With Quote
Old 06-14-2019, 06:03 AM   #12
Mac VP
Senior Member
 
Mac VP's Avatar
 
Join Date: May 2010
Location: Cincinnati, OH
Posts: 1,230
Default Re: 16 spline Slip yoke

We stock them.....it’s made to fit the regular passenger car transmission but will fit the short pickup trans like you have by trimming it down about an inch and a half. They have the same knuckle set up as the original Ford pickup driveshaft did.
__________________
VANPELT SALES LLC
Cincinnati, Ohio
Office: 513-724-9486
www.vanpeltsales.com
www.classictransmission.com
Mac VP is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 10:02 AM.