Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 01-02-2020, 09:58 PM   #1
3twinridges
Senior Member
 
3twinridges's Avatar
 
Join Date: Dec 2015
Posts: 541
Default 8BA aluminum timing cover

Noticed tonight that the aluminum timing cover on our 4” stroke, 1CM cam, and 0BA distributor Flathead has two timing pointer locations. The pin is currently set in the 8RT location with a plug in the 0BA hole. What determines which hole the pointer is located in?

JB
3twinridges is offline   Reply With Quote
Old 01-02-2020, 10:29 PM   #2
3twinridges
Senior Member
 
3twinridges's Avatar
 
Join Date: Dec 2015
Posts: 541
Default Re: 8BA aluminum timing cover

Forgot to mention this engine is in a 52 F1 and running the stock truck pulley.

JB
3twinridges is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 01-02-2020, 10:54 PM   #3
RalphM
Senior Member
 
RalphM's Avatar
 
Join Date: Nov 2015
Location: North Pole, Alaska
Posts: 2,646
Default Re: 8BA aluminum timing cover

8RT is a truck engine, so I would think it’s set right.
RalphM is offline   Reply With Quote
Old 01-02-2020, 11:03 PM   #4
3twinridges
Senior Member
 
3twinridges's Avatar
 
Join Date: Dec 2015
Posts: 541
Default Re: 8BA aluminum timing cover

Thank you

JB
3twinridges is offline   Reply With Quote
Old 01-03-2020, 12:04 AM   #5
flatheadmurre
Senior Member
 
flatheadmurre's Avatar
 
Join Date: Apr 2015
Location: Sweden
Posts: 3,045
Default Re: 8BA aluminum timing cover

The crank pulley diameter is different between car and truck so that is why there is 2 different locations for the pointer.
flatheadmurre is offline   Reply With Quote
Old 01-03-2020, 08:01 AM   #6
Frank Miller
Senior Member
 
Frank Miller's Avatar
 
Join Date: May 2010
Location: Auburn, MA
Posts: 2,106
Default Re: 8BA aluminum timing cover

Sponsored Links (Register now to hide all advertisements)
I'm not sure about the timing difference but pulley diameter will make no difference. The truck hole might be retarded a bit for heavy loads but then again the car heads had higher compression so that would necessitate retarding. Can't see how pulley diameter would make a difference unless the pin locations are one above the other.
__________________
“The technique of infamy is to start two lies at once and get people arguing heatedly over which is true.” ~ Ezra Pound
Frank Miller is offline   Reply With Quote
Old 01-03-2020, 08:32 AM   #7
Ol' Ron
Senior Member
 
Ol' Ron's Avatar
 
Join Date: May 2010
Location: Chester Vt
Posts: 8,840
Default Re: 8BA aluminum timing cover

The worst part of the alum cover is the ware pattern on the cam thrust surface, causing a large cam backlash. One way to check this is with the aluminum ball trick. Attach on to the nose of the cam and rotate the engine. .008'010" is normal. I have found as much as .020 . The only way to fix this is a shim behind the cam timing gear. . WHY?? The excessive baclklash has an effect on timing
Ol' Ron is offline   Reply With Quote
Old 01-03-2020, 09:22 AM   #8
51 MERC-CT
Senior Member
 
51 MERC-CT's Avatar
 
Join Date: May 2010
Location: East Hartford, Ct
Posts: 5,898
Default Re: 8BA aluminum timing cover

The different locations are just to keep the indicator closest to what ever crank pulley is being used. Has nothing to do with timing.
Attached Images
File Type: jpg tmg cov.jpg (26.9 KB, 196 views)
__________________
DON'T RECALL DOING SOMETHING FOR MYSELF BASED ON SOMEONE ELSE'S LIKES OR DISLIKES
51 MERC-CT is offline   Reply With Quote
Old 01-03-2020, 09:38 AM   #9
GOSFAST
Senior Member
 
GOSFAST's Avatar
 
Join Date: May 2010
Location: Long Island, NY
Posts: 1,052
Default Re: 8BA aluminum timing cover

Quote:
Originally Posted by Ol' Ron View Post
The worst part of the alum cover is the ware pattern on the cam thrust surface, causing a large cam backlash. One way to check this is with the aluminum ball trick. Attach on to the nose of the cam and rotate the engine. .008'010" is normal. I have found as much as .020 . The only way to fix this is a shim behind the cam timing gear. . WHY?? The excessive baclklash has an effect on timing
Hi Ron, for some time now when we build with any aluminum covers we install a nylon cam button, same button used for cam end-play in the SBC's.

It's a simple "lay-in" deal, simply sand the front edge to set the end play. Takes only a few minutes to get it right, the nylon sands quickly!

Thanks, Gary in N.Y.

P.S. Wishing all here a very "Happy New Year"
Attached Images
File Type: jpg Flathead Ford Alum T-C Cam Button A.jpg (59.3 KB, 74 views)
File Type: jpg Flathead Ford Alum T-C Cam Button B.jpg (43.2 KB, 72 views)
GOSFAST is offline   Reply With Quote
Old 01-03-2020, 09:41 AM   #10
51 MERC-CT
Senior Member
 
51 MERC-CT's Avatar
 
Join Date: May 2010
Location: East Hartford, Ct
Posts: 5,898
Default Re: 8BA aluminum timing cover

Quote:
Originally Posted by Ol' Ron View Post
The worst part of the alum cover is the ware pattern on the cam thrust surface, causing a large cam backlash. One way to check this is with the aluminum ball trick. Attach on to the nose of the cam and rotate the engine. .008'010" is normal. I have found as much as .020 . The only way to fix this is a shim behind the cam timing gear. . WHY?? The excessive baclklash has an effect on timing
Perhaps a better way to address the problem for most would be to adjust the thickness of the cover to block gasket or eliminate gasket and use liquid gasket.
Then again have appropriate amount of material removed from cover mounting surface.
__________________
DON'T RECALL DOING SOMETHING FOR MYSELF BASED ON SOMEONE ELSE'S LIKES OR DISLIKES
51 MERC-CT is offline   Reply With Quote
Old 01-03-2020, 09:58 AM   #11
51 MERC-CT
Senior Member
 
51 MERC-CT's Avatar
 
Join Date: May 2010
Location: East Hartford, Ct
Posts: 5,898
Default Re: 8BA aluminum timing cover

Quote:
Originally Posted by GOSFAST View Post
Hi Ron, for some time now when we build with any aluminum covers we install a nylon cam button, same button used for cam end-play in the SBC's.

It's a simple "lay-in" deal, simply sand the front edge to set the end play. Takes only a few minutes to get it right, the nylon sands quickly!

Thanks, Gary in N.Y.

P.S. Wishing all here a very "Happy New Year"
Sounds like a better solution.
__________________
DON'T RECALL DOING SOMETHING FOR MYSELF BASED ON SOMEONE ELSE'S LIKES OR DISLIKES
51 MERC-CT is offline   Reply With Quote
Old 01-03-2020, 10:09 AM   #12
3twinridges
Senior Member
 
3twinridges's Avatar
 
Join Date: Dec 2015
Posts: 541
Default Re: 8BA aluminum timing cover

Really good thoughts and I appreciate the responses. Great, you gave me something else to worry about, cam end play....

JB
3twinridges is offline   Reply With Quote
Old 01-03-2020, 11:36 AM   #13
19Fordy
Senior Member
 
19Fordy's Avatar
 
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,872
Default Re: 8BA aluminum timing cover

GOSFAST: That nylon cam button is a neat idea.
19Fordy is offline   Reply With Quote
Old 01-03-2020, 03:59 PM   #14
Ol' Ron
Senior Member
 
Ol' Ron's Avatar
 
Join Date: May 2010
Location: Chester Vt
Posts: 8,840
Default Re: 8BA aluminum timing cover

Thanks Gary, sure sounds like you've solved another pesky flathead problem
Ol' Ron is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 03:46 AM.