|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
08-05-2012, 06:38 PM | #1 |
Senior Member
Join Date: Jun 2012
Location: Waukee, Iowa
Posts: 107
|
Manifold removal help
Any good ideas on how to remove a manifold when the 4 nuts won't budge? I haven't seen much on the forum when I searched. Air driver? Heat?
Thanks for your ideas! |
08-05-2012, 07:18 PM | #2 |
Senior Member
Join Date: May 2010
Location: Portland, Oregon
Posts: 5,892
|
Re: Manifold removal help
Try propane torch heat and tapping after a liberal soaking with PB Blaster, maybe overnight or longer. Turn clockwise slightly fist, then try to back them out, working back and forth.
Of course, be careful with open flame anywhere near fuel.
__________________
Ray Horton, Portland, OR As you go through life, keep your eye on the donut, not the hole. |
Sponsored Links (Register now to hide all advertisements) |
|
08-05-2012, 07:31 PM | #3 |
Junior Member
Join Date: Sep 2010
Location: Wichita, KS
Posts: 2
|
Re: Manifold removal help
Also, use a 1/2" drive, 6 point socket with short extension and breaker bar. Greatly reduces the possibility of rounding off the corners of the nuts. The breaker bar will allow lots of torque at a slower speed than an impact gun. More control of what you are doing.
|
08-05-2012, 07:52 PM | #4 |
Senior Member
Join Date: May 2010
Posts: 2,579
|
Re: Manifold removal help
Tightening slightly works well for rusted threads as mentioned above and in addition if you are turning counter clockwise and nut starts to squeak, stop, get some more PB Blaster on it and turn clockwise a little then continue CCW.
This sounds counter productive but doing so will clear some of the rust dust from between the threads. Similar to when using a tap to cut threads it clears the metal chips from the threads so that you do not damage the new threads and jam the tap in the hole. You may have to go CW, CCW many times if they are really rusted. Resist the tempation to use an impact wrench ... it is too easy to break the studs as you cannot feel or hear the squeak with all the noise. Last edited by Benson; 08-05-2012 at 08:07 PM. |
08-06-2012, 09:40 AM | #5 |
Senior Member
Join Date: Jun 2012
Location: Waukee, Iowa
Posts: 107
|
Re: Manifold removal help
Thanks for the suggestions- Always appreciated.
|
08-07-2012, 07:49 PM | #6 |
Senior Member
Join Date: Jun 2012
Location: Waukee, Iowa
Posts: 107
|
Re: Manifold removal help
Sponsored Links (Register now to hide all advertisements)
Off to get a replacement- Should I get a new intake manifold too in case the old and new don't match up flush? I don't think it was ever sanded/machined but I'm thinking better safe than sorry at this point. Any trick to putting the new one on? Cleaning out the holes on the head?? Or something? I'm not a mechanic and haven't done this before. Thanks! Chuck |
08-07-2012, 07:57 PM | #7 |
Senior Member
Join Date: May 2010
Location: new britain,ct 06052
Posts: 9,389
|
Re: Manifold removal help
If you're only buying the one ck the alignment/flatness to the one not being replaced. You may have to "true" them up. OR take a chance on buying both and maybe NOT having to have them machined "true". I believe you'll want to tighten the two inner nuts first and then the outers. Do a search as there was a discussion here a week or so ago about the washers and torquing.
Paul in CT Paul in CT |
08-07-2012, 09:53 PM | #8 |
Senior Member
Join Date: May 2010
Location: So Minn
Posts: 1,565
|
Re: Manifold removal help
I had no problem getting the nuts off but can't get the manifold loose from the head. Any ideas on that?
|
08-07-2012, 10:05 PM | #9 |
Senior Member
Join Date: Jun 2012
Location: Waukee, Iowa
Posts: 107
|
Re: Manifold removal help
You may have already, but make sure the muffler/tailpipe is disconnected from the exhaust manifold. If it still isn't loose, you might hit the back of the manifold with a deadblow/rubber hammer to pop it loose from the gaskets.
|
08-07-2012, 11:50 PM | #10 |
Senior Member
Join Date: Nov 2011
Location: B.C. Canada
Posts: 1,746
|
Re: Manifold removal help
Sometimes if the ex manifold is badly warped downwards it will bind against the studs.Lay a straight edge even with edge of 3 front ports & the rear one will often be lower than the rest.Generaly caused by tail pipe clamp being too tight& muffler expanding in length when hot & pushing manifold forward.
|
Thread Tools | |
Display Modes | |
|
|
Sponsored Links (Register now to hide all advertisements) |
|