Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 11-26-2017, 07:24 PM   #101
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,937
Default Re: Rare '40 convertible restoration project

Here's some "after" photos...
Attached Images
File Type: jpg P1040253.jpg (45.0 KB, 259 views)
File Type: jpg P1040254.jpg (41.9 KB, 233 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is online now   Reply With Quote
Old 11-27-2017, 04:08 AM   #102
A bones
Senior Member
 
A bones's Avatar
 
Join Date: May 2010
Location: CLAYTON DE
Posts: 1,280
Default Re: Rare '40 convertible restoration project

I always look forward to an early spring. I hope the next is as nice as yours'!
__________________
Enjoy yer day. Tom
Hate can't fix what it started.
A bones is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 11-27-2017, 04:43 AM   #103
Mart
Senior Member
 
Mart's Avatar
 
Join Date: May 2010
Location: Solihull, England.
Posts: 8,732
Default Re: Rare '40 convertible restoration project

Thanks for the write-up, Mike. Tell me, what sort of material are the covers made from, and how do you apply it?

Mart.
Mart is offline   Reply With Quote
Old 01-22-2018, 11:05 AM   #104
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,937
Default Re: Rare '40 convertible restoration project

Hey guys! Well, I'm finally back at this project. Between the holiday's and health issues it's been a tough recent past.
Anyway, I managed to get the frame done and have started to assemble it. I typically have all of the subassemblies done and ready to install so this process goes rather quickly.
Attached Images
File Type: jpg P1040276.jpg (67.0 KB, 182 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is online now   Reply With Quote
Old 01-22-2018, 11:08 AM   #105
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,937
Default Re: Rare '40 convertible restoration project

I'm also back at the (main) body. The inside of this is already painted. The outside, sans the bottom, has the guide coat applied. The bottom, as can be seen here, needs little to bring it to the same point. I'm hoping I can get this painted within the next few weeks.
Attached Images
File Type: jpg P1040277.jpg (52.4 KB, 184 views)
File Type: jpg P1040278.jpg (49.0 KB, 166 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is online now   Reply With Quote
Old 01-22-2018, 11:12 AM   #106
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,937
Default Re: Rare '40 convertible restoration project

Sponsored Links (Register now to hide all advertisements)
Quote:
Originally Posted by Mart View Post
Thanks for the write-up, Mike. Tell me, what sort of material are the covers made from, and how do you apply it?

Mart.
Hi ya Mart,
See post #100 for a fairly thorough explanation of how I install these covers. As original, they are simply galvanized sheet metal.
These reproductions have been duplicated (exactly) from original sets.
The first time I'd installed a set it took me better than two hours. I can now do a set in about 1/2 hour.
I've learned a few tricks though past trials and tribulations
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is online now   Reply With Quote
Old 01-22-2018, 11:18 AM   #107
37fatfender
Senior Member
 
37fatfender's Avatar
 
Join Date: May 2010
Location: Mesquite, NV / Gurnee, IL
Posts: 298
Default Re: Rare '40 convertible restoration project

Kube, Beautiful work! My question is in regards to the frame vs the body. I have tinkered with replacing sheet metal panels over the years, but it escapes me on how you would restore 10 guage steel frame rails. This era Ford frame is notorious for having rust between the riveted rails especially in the "S" bend at the rear of the frame. I saw your beginning photos so I am sure there was some rust. Do you remove all the rivets and reassemble the frame? What paint do you use to paint your frames?
37fatfender is offline   Reply With Quote
Old 01-22-2018, 12:02 PM   #108
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,937
Default Re: Rare '40 convertible restoration project

Quote:
Originally Posted by 37fatfender View Post
Kube, Beautiful work! My question is in regards to the frame vs the body. I have tinkered with replacing sheet metal panels over the years, but it escapes me on how you would restore 10 guage steel frame rails. This era Ford frame is notorious for having rust between the riveted rails especially in the "S" bend at the rear of the frame. I saw your beginning photos so I am sure there was some rust. Do you remove all the rivets and reassemble the frame? What paint do you use to paint your frames?
This particular frame had rot directly beneath the battery box. After cutting back to solid metal and removing any necessary rivets, I butt weld in a piece of steel of the exact same thickness of the adjoining frame area.

I did have to replace a piece in that "S" bend you'd referred to a past restoration. I use the same method as anywhere else on a frame - cut out the offending area, remove rivets as necessary and butt weld in steel of the same thickness. This area is difficult to do as you know.

I use single stage paint on the frames for the finish coat. For the prep, etching primer and primer (of course) followed by (too) many hours of wet sanding.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is online now   Reply With Quote
Old 01-22-2018, 12:44 PM   #109
37fatfender
Senior Member
 
37fatfender's Avatar
 
Join Date: May 2010
Location: Mesquite, NV / Gurnee, IL
Posts: 298
Default Re: Rare '40 convertible restoration project

You make it sound so easy!!!! But how do you get the round bend at the top and bottom of the frame rail. These were pressed by Ford on huge presses, this is the area that's not often duplicated by the aftermarket frame guys. Who just three pieces of steel to form the "C" channel. And although they look pretty flat and straight from a side profile, there more than a few curves and bends pressed into the frame rails..
37fatfender is offline   Reply With Quote
Old 01-22-2018, 12:57 PM   #110
Mart
Senior Member
 
Mart's Avatar
 
Join Date: May 2010
Location: Solihull, England.
Posts: 8,732
Default Re: Rare '40 convertible restoration project

Kube, the chassis and underfloor pics look fantastic.

Kube, If I post any pics, please don't look at 'em, might put you off your lunch.

Re the curve on the edge of the frame, when I did a similar job I cut the patch piece from a piece of square tube and used the curved edge to simulate the curve on the frame rail. I used about 1/2" of the one side and made the join that far down the side. I imagine Mike does it a lot tidier, though.

Mart.
Mart is offline   Reply With Quote
Old 01-22-2018, 03:03 PM   #111
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,937
Default Re: Rare '40 convertible restoration project

Quote:
Originally Posted by 37fatfender View Post
You make it sound so easy!!!! But how do you get the round bend at the top and bottom of the frame rail. These were pressed by Ford on huge presses, this is the area that's not often duplicated by the aftermarket frame guys. Who just three pieces of steel to form the "C" channel. And although they look pretty flat and straight from a side profile, there more than a few curves and bends pressed into the frame rails..
Being a retired tool & die maker has its advantages
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is online now   Reply With Quote
Old 01-22-2018, 03:21 PM   #112
rockfla
Senior Member
 
rockfla's Avatar
 
Join Date: Mar 2014
Location: Jacksonville FL
Posts: 3,927
Default Re: Rare '40 convertible restoration project

Kube
You remind me of my neighbor, He was a GS-14 machinist at the local Navel Refit Facility....he was having a garage/shop built at his house and it was driving him nuts from the foundation to the framers to the trim carpenter how "cavalier" they were being a 1/16th to 1/8 off!!!! Nuts I tell you, drove him nuts!!!! My other buddy who is a "professional" model builder (or at least that's what I call him, he actually does it for fun) he has spent 100 hours on a paint job on a 1/24th model. My best friend said he can "pick fly crap outta pepper".......I showed him your work and He said to tell you the first step to recovery is recognition!!! He loved your work by the way....I will have to post a few of his models he builds, like your work...phenomenal!!!!!

Last edited by rockfla; 01-22-2018 at 03:26 PM.
rockfla is offline   Reply With Quote
Old 01-22-2018, 05:27 PM   #113
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,937
Default Re: Rare '40 convertible restoration project

Quote:
Originally Posted by rockfla View Post
Kube
You remind me of my neighbor, He was a GS-14 machinist at the local Navel Refit Facility....he was having a garage/shop built at his house and it was driving him nuts from the foundation to the framers to the trim carpenter how "cavalier" they were being a 1/16th to 1/8 off!!!! Nuts I tell you, drove him nuts!!!! My other buddy who is a "professional" model builder (or at least that's what I call him, he actually does it for fun) he has spent 100 hours on a paint job on a 1/24th model. My best friend said he can "pick fly crap outta pepper".......I showed him your work and He said to tell you the first step to recovery is recognition!!! He loved your work by the way....I will have to post a few of his models he builds, like your work...phenomenal!!!!!
Every time I start to believe I am truly crazy, I hear about a guy like your best friend and think "now that guy is crazy"!
As long as there are guys spending a 100 hours on a 1/24th model kit paint job, "I'm okay".

When I built my last home, I was a lot of "hands on" and like your neighbor, I was insistent that the house be "true". Let me tell ya, it was...

In all seriousness, this retentiveness is not what some might think is such a good thing. The drive to perfection has an impossible arrival point. There simply is no such thing as "perfection". Still, I'll keep chasing it

Thanks for your kind words!
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is online now   Reply With Quote
Old 01-22-2018, 07:28 PM   #114
rotorwrench
Senior Member
 
rotorwrench's Avatar
 
Join Date: Jun 2010
Location: San Antonio, Texas
Posts: 16,371
Default Re: Rare '40 convertible restoration project

If your happy with something, most of us here know it's got to be pretty damn close to as good as it gets. Not a thing wrong with that as long as your OK with it. That's going to be one damn fine car when you're as close to done as you care to get. The rest of us will just drool a bit with a look of awe. It's rare to see them so close to factory show room fresh.
rotorwrench is offline   Reply With Quote
Old 01-22-2018, 09:04 PM   #115
fordor
Member
 
Join Date: May 2010
Location: Michigan
Posts: 87
Default Re: Rare '40 convertible restoration project

Where do you get the spring covers from? I need to replace mine.
Thanks,
Bob L.
fordor is offline   Reply With Quote
Old 01-23-2018, 12:40 AM   #116
35fordtn
Senior Member
 
35fordtn's Avatar
 
Join Date: Aug 2010
Location: McMinnville, TN
Posts: 2,327
Default Re: Rare '40 convertible restoration project

Mike,
Looks great! You get a big thumbs up from the hillbilly here in TN (me). I admire the attention to the details.

Question.... Typically when you do a 1940 do you prefer to install the steering gear before or after the body is set?
35fordtn is offline   Reply With Quote
Old 01-23-2018, 09:37 AM   #117
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,937
Default Re: Rare '40 convertible restoration project

Quote:
Originally Posted by 35fordtn View Post
Mike,
Looks great! You get a big thumbs up from the hillbilly here in TN (me). I admire the attention to the details.

Question.... Typically when you do a 1940 do you prefer to install the steering gear before or after the body is set?
Mike,
Thanks for the kind words.

I install the gear prior to the body drop. Makes my life so much easier. I don't tighten the gear to the frame until the instrument panel is completely installed.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is online now   Reply With Quote
Old 01-23-2018, 01:56 PM   #118
Chris
Senior Member
 
Chris's Avatar
 
Join Date: May 2010
Location: Spokane, WA
Posts: 2,976
Default Re: Rare '40 convertible restoration project

Beautiful
__________________
Thee Inland Emperors
Chris is offline   Reply With Quote
Old 01-24-2018, 03:12 PM   #119
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,937
Default Re: Rare '40 convertible restoration project

Got the bottom of the floor primed today. I hope to have it painted in the next few days.
Attached Images
File Type: jpg P1040282.jpg (47.8 KB, 142 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is online now   Reply With Quote
Old 01-24-2018, 04:23 PM   #120
Seth Swoboda
Senior Member
 
Seth Swoboda's Avatar
 
Join Date: May 2010
Location: Southern Illinois
Posts: 3,744
Default Re: Rare '40 convertible restoration project

Simply unreal. I guess I've got lots of work to do on this '40 project of mine!
Seth Swoboda is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 08:16 PM.