|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
04-19-2017, 12:09 PM | #1 |
Senior Member
Join Date: May 2010
Location: Star, MS
Posts: 4,024
|
removing broken alemite
I'm trying to remove the broken threaded section of an alemite. It is on the pitman shaft housing of a steering gear and I don't have room between the gear and the engine to tap the easy out to make it bite. It just twists in the hole. Are the alemites too hard for the easy out to bite? Anybody have a trick for this?
|
04-19-2017, 01:08 PM | #2 |
Senior Member
Join Date: May 2010
Posts: 2,173
|
Re: removing broken alemite
Maybe too soft. Drop the arm for room. Jack E/NJ
|
Sponsored Links (Register now to hide all advertisements) |
|
04-19-2017, 03:30 PM | #3 |
Senior Member
Join Date: May 2010
Location: upstate SC
Posts: 2,963
|
Re: removing broken alemite
maybe take a screw driver and use it as a lever to put pressure on the easy out. no alemite fittings are usually very soft
|
04-19-2017, 03:44 PM | #4 |
Senior Member
Join Date: May 2010
Location: Star, MS
Posts: 4,024
|
Re: removing broken alemite
I've been fighting this thing off and on for a couple of days. Sometimes it feels like it bites then strips out. Now that I have the hole opened up I think I'll try one of those rubber tipped needle fittings and see if I can put enough pressure on it to get some grease in it.
|
04-19-2017, 04:57 PM | #5 |
Senior Member
Join Date: May 2010
Location: Solihull, England.
Posts: 8,752
|
Re: removing broken alemite
Sorry to be a bit thick but what is an alemite??
__I googled it - You're talking of what we call a grease nipple. You could try tapping a suitable sized torx bit into it. It worked for me on a clutch bolt. EZ outs tend to be a nightmare if they break off. Mart |
04-19-2017, 05:08 PM | #6 |
Senior Member
Join Date: May 2010
Location: Canada Where it snows
Posts: 2,058
|
Re: removing broken alemite
Sponsored Links (Register now to hide all advertisements)
Can hardly wait to hear what the Kippers call them."LOL" R |
04-19-2017, 05:57 PM | #7 |
Member Emeritus
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
|
Re: removing broken alemite
Mart, I had the same question! Never head the term.
|
04-19-2017, 06:17 PM | #8 |
Senior Member
Join Date: May 2010
Posts: 2,173
|
Re: removing broken alemite
>>>Sorry to be a bit thick but what is an alemite??>>>I had the same question! Never head the term.>>>
Troglodytes. 8^) Jack E/NJ |
04-19-2017, 06:37 PM | #9 |
Senior Member
Join Date: May 2010
Location: Canada Where it snows
Posts: 2,058
|
Re: removing broken alemite
Where have you guy's been hanging out under a rock holy cow!!!"LOL" Just sayin.
https://en.wikipedia.org/wiki/Grease_fitting R |
04-19-2017, 06:50 PM | #10 |
Senior Member
Join Date: May 2010
Location: Central Illinois
Posts: 370
|
Re: removing broken alemite
I believe that Alemite is a name brand. The generic name is grease zerk or grease nipple, etc.. The use of Alemite is like calling all facial tissue Kleenex. If you are older and from the U.S. or Canada you have likely heard the name Alemite.
__________________
I've got the old car disease. Thankfully there's no cure! |
04-19-2017, 06:55 PM | #11 |
Member Emeritus
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
|
Re: removing broken alemite
OK, I'm old, from the US and worked on cars my whole life and never heard the term! Maybe it's a regional term.
|
04-19-2017, 08:12 PM | #12 |
Senior Member
Join Date: May 2010
Location: Columbia, SC
Posts: 1,579
|
Re: removing broken alemite
|
04-19-2017, 08:15 PM | #13 |
Senior Member
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,943
|
Re: removing broken alemite
Take the small metal file and bend the tang 90 degrees so it fits inside the fitting.
Hit it with a hammer to drive it in. Then twist. Keep doing this. Fittings are soft. |
04-19-2017, 08:21 PM | #14 |
Senior Member
Join Date: Jul 2011
Location: SF Bay Area
Posts: 6,645
|
Re: removing broken alemite
Alemite grease gun
__________________
Alan |
04-19-2017, 08:28 PM | #15 |
Senior Member
Join Date: Feb 2011
Location: Monroe, Wi
Posts: 247
|
Re: removing broken alemite
If you have a drill that has reverse on it (counter clockwise) you could use a left hand drill bit, they normally will spin right out when the drill catches. Although not a normal hardware store item they are available from Mcmaster Carr and many other sources.
Regards, Brian |
04-20-2017, 03:20 AM | #16 |
Senior Member
Join Date: Apr 2011
Location: Hertford (UK)
Posts: 905
|
Re: removing broken alemite
Sounds more like a gill to me.....now Mart knows what a gill is
|
04-20-2017, 05:02 AM | #17 |
Senior Member
Join Date: May 2010
Location: Kingman Az. 86409
Posts: 419
|
Re: removing broken alemite
New one on me. Worked 40+yrs at Ford dealers in Detroit starting in the 60's. Working with my old man he already had 20yrs working there. Some of the old guys (seemed ancient to me) had experience with model T's & A's. Never once did I hear one of them refer to an "alemite". Fast forward to the time I retired some of the kids there didn't know what a grease fitting was.
__________________
Dan Kingman Az. 86409 |
04-20-2017, 06:02 AM | #18 |
Senior Member
Join Date: May 2010
Location: Cocoa Florida
Posts: 180
|
Re: removing broken alemite
When I worked in a parts house back in the 70's , we sold Alemite products which consisted of grease fittings and grease guns.
|
04-20-2017, 06:34 AM | #19 |
Senior Member
Join Date: May 2010
Location: Solihull, England.
Posts: 8,752
|
Re: removing broken alemite
Well we all learnt something.
You really do learn something new every day, and embracing these differences is part of the fun. Mart Oh yeah, got it out yet?? |
04-20-2017, 08:13 AM | #20 |
Senior Member
Join Date: May 2010
Posts: 2,173
|
Re: removing broken alemite
Prolly buggered up the threads in the shaft housing by now. 8^0 Jack E/NJ
|
04-20-2017, 08:15 AM | #21 | |
Member Emeritus
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
|
Re: removing broken alemite
Quote:
Last edited by JSeery; 04-20-2017 at 08:35 AM. |
|
04-20-2017, 09:18 AM | #22 |
Senior Member
Join Date: May 2010
Location: Star, MS
Posts: 4,024
|
Re: removing broken alemite
No, Mart, it is not out.
No, Jack, I can't get anything to bite enough to bugger it up. I'm going to try to find a left hand bit today. I would pull the steering gear but a lot of parts would have to come off to do that. I'm still holding out hope that the rubber tipped grease needle will work. |
Sponsored Links (Register now to hide all advertisements) |
|
04-20-2017, 10:32 AM | #23 |
Member Emeritus
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
|
Re: removing broken alemite
I have never had any luck with the tapered twist type of easy-outs. However I have a set of straight splined extractors that work really well. You drill a hole the size of the base and tap them in. Have always worked well for me (in the right application).
Last edited by JSeery; 04-20-2017 at 10:38 AM. |
04-25-2017, 06:06 PM | #24 |
Senior Member
Join Date: May 2010
Location: Star, MS
Posts: 4,024
|
Re: removing broken alemite
Update on the broken alemite, grease zerk, grease fitting, etc. The rubber tipped needle worked to get grease in the broken fitting, but the pressure on the grease just pushed a lot of it back out the hole. Thinking that a grease fitting holding pressure would be better, I finally took off enough parts to get better access to the fitting. The left hand drill didn't back it out, so I drilled and tapped the hole for the fitting. It took a lot of fretting, but I'm glad it is done correctly.
|
04-26-2017, 02:32 PM | #25 |
Senior Member
Join Date: Feb 2011
Location: Maltby, Washington
Posts: 187
|
Re: removing broken alemite
Thanks for the update and also for the word Alemite. I am with many others on this site in that I had never heard the word before so I learned something new.
|
04-26-2017, 02:59 PM | #26 |
Senior Member
Join Date: Mar 2016
Location: Lynden, WA
Posts: 1,564
|
Re: removing broken alemite
Sponsored Links (Register now to hide all advertisements)
http://www.alemite.com/catalog/detai...ifier=fittings |
04-26-2017, 03:27 PM | #27 |
Senior Member
Join Date: May 2010
Location: Solihull, England.
Posts: 8,752
|
Re: removing broken alemite
I prefer nipples.
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|