04-28-2019, 08:28 PM | #1 |
Senior Member
Join Date: May 2010
Location: warwick Rhode Island
Posts: 464
|
link
Having a problem removing sway bar Link, should be a simple task, but i'm stomped. (40 Ford)
Any suggestions would be very much appreciated. Thanks. Hope |
04-28-2019, 09:25 PM | #2 |
Senior Member
Join Date: Feb 2019
Location: Wichita Kansas
Posts: 134
|
Re: link
On my 47 I used a big sledge on the backside to back it up, not hit it, then a small hammer to knock it out.
|
Sponsored Links (Register now to hide all advertisements) |
|
04-29-2019, 06:07 PM | #3 |
Senior Member
Join Date: May 2010
Location: warwick Rhode Island
Posts: 464
|
Re: link
Thanks Sodbuster
But i have already done that, and had to resort to using the torch to heat it up, and with a BFH really wack at it with no result. |
04-30-2019, 07:18 AM | #4 |
Senior Member
Join Date: Feb 2019
Location: Wichita Kansas
Posts: 134
|
Re: link
I would pull the sway bar and go to the vise, some of these parts have been on so long they really have to be solid when you give them a wack to get them apart, might as well replace the two sway bar bushings while your at it.
|
04-30-2019, 07:43 AM | #5 |
Senior Member
Join Date: Dec 2015
Posts: 287
|
Re: link
I use a pickle fork, like is used for tie rod ends.
|
04-30-2019, 12:16 PM | #6 |
Senior Member
Join Date: May 2010
Location: warwick Rhode Island
Posts: 464
|
Re: link
Sponsored Links (Register now to hide all advertisements)
My next step was that , to remove the sway bar, and good idea to use the pickle fork, will give it a try. |
04-30-2019, 09:15 PM | #7 |
Senior Member
Join Date: May 2010
Location: warwick Rhode Island
Posts: 464
|
Re: link
SHUCKS, the only pickle fork i have is to big ??????????
Will try again tomorrow, to think of something else. |
05-01-2019, 02:51 PM | #8 |
Senior Member
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,990
|
Re: link
There is a special press tool that is made for removing tie rods ends w/o damaging them. Available at any decent auto parts store, I've used one on every 40 sway bar (and tie rod ends) I've ever restored.
__________________
"I can explain it for you. However, I can't understand it for you". |
05-01-2019, 07:41 PM | #9 |
Senior Member
Join Date: May 2010
Location: warwick Rhode Island
Posts: 464
|
Re: link
Thanks Kube
Got one side free today, after all that struggle it came free, easily (well kind-of). Will try the other side tomorrow, and if i have too much trouble i'll keep your suggestion in mind. (slow progress, but its better than noting) |
05-02-2019, 10:30 PM | #10 |
Senior Member
Join Date: May 2010
Location: warwick Rhode Island
Posts: 464
|
Re: link
"YYYYAAAHH" Got it done both sides, thanks for the help guys. Hope |
05-02-2019, 10:35 PM | #11 |
Senior Member
Join Date: May 2010
Location: MN
Posts: 7,053
|
Re: link
What'd ya do? pickle fork seems like a decent way and common way for tie rods. so sway bar?
|
05-03-2019, 08:02 AM | #12 | |
Senior Member
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,990
|
Re: link
Quote:
A pickle fork works on the sway bar swivels. I don't care for a fork in any situation that I plan on reusing the part. They have a tendency to stretch the ball / socket as you surely realize.
__________________
"I can explain it for you. However, I can't understand it for you". |
|
05-03-2019, 01:37 PM | #13 |
Senior Member
Join Date: May 2010
Location: warwick Rhode Island
Posts: 464
|
Re: link
The only pickle fork i had, was to big (wide). And i didn't plan on reusing the links, i was replacing them was my goal.
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|