The Ford Barn

BUBBAS IGNITION · 09-07-2017, 02:31 PM

Any one got one of these on their engine??. I need a picture of it on a running engine ......

Brian T · 09-07-2017, 03:38 PM

I thought your request was pretty straightforward too ---- , what the peanut gallery doesn't know is how to mark the pulley for correct top dead center. Keep up the good work, sorry I couldn't help with your request.

zzlegend · 09-07-2017, 03:51 PM

X2 what Brian said. Some wanna be experts need to go back to the other forum.

Some one will get back to you Bubba, with the right answer.

Kevin in NJ · 09-07-2017, 03:58 PM

Umm, have you tried doing a search on the forum?

There have been many discussions about these things with pictures and stuff. Probably if you search Youtube you will find video.

As for the experts, well many have decided it is best to move on.

Benson · 09-07-2017, 04:30 PM

I will look on home computer later for photo of part installed.

My shop machine does not have as many photos.

divcoone · 09-07-2017, 04:32 PM

Sponsored Links (Register now to hide all advertisements)

Not sure if this is what you are looking for, but here is mine.

Benson · 09-07-2017, 04:48 PM

Bubba how is this?

This photo has Nu Rex written on this part ...

CarlG · 09-07-2017, 05:05 PM

Reading the posts above, I must have missed something.

This picture is not the NuRex gauge, but it shows the one I have on my engine.

Y-Blockhead · 09-07-2017, 05:53 PM

Quote:

Originally Posted by CarlG

Reading the posts above, I must have missed something.

Looks like DaWizard/RawhideKid got himself banned a second time...

Benson · 09-07-2017, 06:11 PM

Whew that was close ... I was going to say something about a Snotty remark that someone made. But chose to remain silent ...

Now his post is gone.

Bob from Northport · 09-07-2017, 07:26 PM

We have used that item on a number of engines. It is easiest to set TDC on an engine with the radiator out. Then use a file and cut a small groove into the crank pulley with the gauge attached. Make sure the engine is at TDC using the timing pin and visually checking the #1 piston the verify it is at TDC. A 6 volt timing light can be used to easily set the timing to various degrees. The engine will start and gun great. The photo is a NURex sold item. See them a Hershey

BUBBAS IGNITION · 09-07-2017, 08:14 PM

Thanks guys , I got it .. Just needed a visual and didn't have a Model A engine handy. Thanks again........

michael a · 09-09-2017, 09:38 AM

At what degree are you setting the timing at an idle

Sent from my SM-J700T using Tapatalk

09-07-2017, 03:38 PM	#2
Brian T Senior Member Join Date: May 2010 Location: San Diego,Ca Posts: 1,377	Re: Nu Rex timing pointer for Model a?? I thought your request was pretty straightforward too ---- , what the peanut gallery doesn't know is how to mark the pulley for correct top dead center. Keep up the good work, sorry I couldn't help with your request. __________________ Nothing can be made foolproof, ---- fools are ingenious bastards.

09-07-2017, 03:51 PM	#3
zzlegend Senior Member Join Date: May 2010 Location: Reseda, Calif. Posts: 2,188	Re: Nu Rex timing pointer for Model a?? X2 what Brian said. Some wanna be experts need to go back to the other forum. Some one will get back to you Bubba, with the right answer.

09-07-2017, 03:58 PM	#4
Kevin in NJ Senior Member Join Date: May 2010 Location: South East NJ Posts: 3,398	Re: Nu Rex timing pointer for Model a?? Umm, have you tried doing a search on the forum? There have been many discussions about these things with pictures and stuff. Probably if you search Youtube you will find video. As for the experts, well many have decided it is best to move on.

09-07-2017, 04:30 PM	#5
Benson Senior Member Join Date: May 2010 Posts: 2,597	Re: Nu Rex timing pointer for Model a?? I will look on home computer later for photo of part installed. My shop machine does not have as many photos. Last edited by Benson; 09-07-2017 at 06:12 PM.

09-07-2017, 06:11 PM	#10
Benson Senior Member Join Date: May 2010 Posts: 2,597	Re: Nu Rex timing pointer for Model a?? Whew that was close ... I was going to say something about a Snotty remark that someone made. But chose to remain silent ... Now his post is gone.

09-07-2017, 07:26 PM	#11
Bob from Northport Senior Member Join Date: May 2010 Location: 215 E. 6th Street Northport, Michigan 49670 Posts: 941	Re: Nu Rex timing pointer for Model a?? We have used that item on a number of engines. It is easiest to set TDC on an engine with the radiator out. Then use a file and cut a small groove into the crank pulley with the gauge attached. Make sure the engine is at TDC using the timing pin and visually checking the #1 piston the verify it is at TDC. A 6 volt timing light can be used to easily set the timing to various degrees. The engine will start and gun great. The photo is a NURex sold item. See them a Hershey __________________ Bob from Northport Northport, Michigan

09-07-2017, 08:14 PM	#12
BUBBAS IGNITION Senior Member Join Date: May 2010 Location: SPEEDWAY INDIANA Posts: 4,148	Re: Nu Rex timing pointer for Model a?? Thanks guys , I got it .. Just needed a visual and didn't have a Model A engine handy. Thanks again........ __________________ If it Makes Spark, we do it !!!! www.bubbasignition.com [email protected]

09-09-2017, 09:38 AM	#13
michael a Senior Member Join Date: Feb 2015 Location: Lone Jack Missouri Posts: 381	Re: Nu Rex timing pointer for Model a?? At what degree are you setting the timing at an idle Sent from my SM-J700T using Tapatalk