Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 02-22-2013, 11:43 AM   #1
LSJUNIPER
Senior Member
 
Join Date: Aug 2011
Location: CT
Posts: 215
Default Flathead project

This is a flathead motor I bought to tinker around with, I want to learn more about these motors. I believe it's a 39 to 41.

101_0884.jpg

101_0882.jpg


Will attach more pics as I brake the motor down..
LSJUNIPER is offline   Reply With Quote
Old 02-22-2013, 01:39 PM   #2
Bruce Lancaster
Member Emeritus
 
Join Date: May 2010
Location: Madison, NJ
Posts: 5,230
Default Re: Flathead project

Side view shows the '39-40 bulges, it seems to have the long crank so not 1938.
Next--pop a head and we can tell for sure whether 221 or 239 originally. It has pulley setup for big truck, and many of those came with 239.
Bruce Lancaster is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 02-22-2013, 03:31 PM   #3
G.M.
Senior Member
 
Join Date: May 2010
Location: Florida and Penna.
Posts: 4,471
Default Re: Flathead project

It was out of a big truck or a stationary engine. It had a generator fan. Sounds like a worth while project. G.M.
__________________
www.fordcollector.com
G.M. is offline   Reply With Quote
Old 02-22-2013, 09:18 PM   #4
ford3
Senior Member
 
Join Date: Oct 2012
Location: oroville calif.
Posts: 1,453
Default Re: Flathead project

if it was out of a big truck try and find a set of heads from a car, truck heads are low compression
ford3 is offline   Reply With Quote
Old 02-22-2013, 09:20 PM   #5
brien
Member
 
brien's Avatar
 
Join Date: Feb 2013
Location: Brooklyn CT
Posts: 98
Default Re: Flathead project

Weren't the bell housings attached to the block up until 1948 or 49? After that they could be split off, I think..???
brien is offline   Reply With Quote
Old 02-22-2013, 09:43 PM   #6
quickchange34
Senior Member
 
quickchange34's Avatar
 
Join Date: May 2010
Location: charlottesville, Va.
Posts: 588
Default Re: Flathead project

Sponsored Links (Register now to hide all advertisements)
I think you need to get it off that motor stand ASAP. You may find it in the floor, if not now its a good chance when you start swinging a wrench on it. The rear of the blocks on the 48 and back cant stand the pressure.
quickchange34 is offline   Reply With Quote
Old 02-22-2013, 10:20 PM   #7
Walt Dupont--Me.
Senior Member
 
Walt Dupont--Me.'s Avatar
 
Join Date: May 2010
Location: Gardiner Me.
Posts: 4,200
Default Re: Flathead project

From here I'd call it a 42. It will pass the pencil test and I cain't see any bluges in the pan rail for any core plugs. See if the intake manafold gasket surface is raised up a little from the block. Walt
Walt Dupont--Me. is offline   Reply With Quote
Old 02-22-2013, 10:57 PM   #8
G.M.
Senior Member
 
Join Date: May 2010
Location: Florida and Penna.
Posts: 4,471
Default Re: Flathead project

Hey Walt, I stopped by your place in my 39 P/U in 2006 on my way to Nova Scotia. I had a shrould and a 6 bladed fan on the generator if you recall. G.M.
__________________
www.fordcollector.com
G.M. is offline   Reply With Quote
Old 02-23-2013, 10:02 AM   #9
Walt Dupont--Me.
Senior Member
 
Walt Dupont--Me.'s Avatar
 
Join Date: May 2010
Location: Gardiner Me.
Posts: 4,200
Default Re: Flathead project

Quote:
Originally Posted by G.M. View Post
Hey Walt, I stopped by your place in my 39 P/U in 2006 on my way to Nova Scotia. I had a shrould and a 6 bladed fan on the generator if you recall. G.M.
Hey GM. I remember that, it was a nice summer day. You and your wife and a friend of mine, we set in lawn chairs in from my shop and had great visit. I remember you drove in my drive and got out, opened the hood and pointed you heat gun at everything under the hood,it was running as cool a clam with Ships pumps, 6 bladded fan, shrould. Stop in again when you go to Nova Scotia. Walt
Walt Dupont--Me. is offline   Reply With Quote
Old 02-23-2013, 08:12 PM   #10
LSJUNIPER
Senior Member
 
Join Date: Aug 2011
Location: CT
Posts: 215
Default Re: Flathead project

I took the oil pan off, there is four freeze plugs. Does that make it a 39 to 41? The person I bought it from said it came out of a truck. The water pumps also had double pulleys......
LSJUNIPER is offline   Reply With Quote
Old 02-25-2013, 06:04 AM   #11
LSJUNIPER
Senior Member
 
Join Date: Aug 2011
Location: CT
Posts: 215
Default Re: Flathead project

The intake and heads are off.

~8755551.jpg

~9280949.jpg
LSJUNIPER is offline   Reply With Quote
Old 02-25-2013, 06:06 AM   #12
LSJUNIPER
Senior Member
 
Join Date: Aug 2011
Location: CT
Posts: 215
Default Re: Flathead project

The motor is stuck, I will be soaking it in oil....
LSJUNIPER is offline   Reply With Quote
Old 02-25-2013, 06:27 AM   #13
Walt Dupont--Me.
Senior Member
 
Walt Dupont--Me.'s Avatar
 
Join Date: May 2010
Location: Gardiner Me.
Posts: 4,200
Default Re: Flathead project

The water pumps are truck. Scrape around the top of the cyl and see if you can see a sign of sleeves in the cyl. The 40-1 had sleeves, I don't think the 39 had sleeves. Walt
Walt Dupont--Me. is offline   Reply With Quote
Old 02-25-2013, 07:53 AM   #14
Mart
Senior Member
 
Mart's Avatar
 
Join Date: May 2010
Location: Solihull, England.
Posts: 8,733
Default Re: Flathead project

It's hard to tell from the photo, but it does not look full of rust and crud in the bores, they look quite clean. So if stuck, it may not have been stuck for long. Again, hard to tell from the pic, but it looks like it may be relieved. My relieved blocks are sort of machined out with a parallel sided cut. That looks like it is shaped to the gasket, ie hand done.
I may be imagining the relief, hard to tell from the pics.

I'd be pulling the starter and pumps, manifold and distributor. Anything to take weight off it. You have already been told about the dangers of supporting on the early bellhousing.

If you pull the sump you can lever against the ring gear teeth to try and turn it.

Be very careful though, it's easy to overdo it, an engine on a stand is very top-heavy.

Mart.

Edit: Ignore my ramblings re the relief, the gasket is still on, isn't it?

Oh yeah, measured the bore yet? A rough measurement should be good enough to tell the original size.
Mart is offline   Reply With Quote
Old 02-25-2013, 09:05 AM   #15
harley
Member
 
Join Date: Dec 2012
Location: Ouachita County Arkansas
Posts: 59
Default Re: Flathead project

Pull the front cover and the cam gear. The valves are probably stuck. If you pry on it too hard you could ruin a good cam and some lifters. Harley
__________________
people have more trouble than anybody
harley is offline   Reply With Quote
Old 02-25-2013, 09:28 AM   #16
Mike in AZ
Senior Member
 
Mike in AZ's Avatar
 
Join Date: May 2010
Location: Waddell, AZ
Posts: 2,540
Default Re: Flathead project

is the passenger side exhaust manifold rusted out??...otherwise, bores, etc. do look clean....under intake??...keep on having fun....Mike
Mike in AZ is offline   Reply With Quote
Old 02-25-2013, 09:43 AM   #17
Gumpy
Senior Member
 
Gumpy's Avatar
 
Join Date: May 2010
Location: Sf bay area
Posts: 1,464
Default Re: Flathead project

Marvel mystery oil is a good oil to soak the engine in--ive used it on several...good luck. gump
__________________
"I believe God is managing affairs and that He doesn't need any advice from me. With God in Charge, I believe everything will work out for the best in the end. So what is there to worry about". Quote by Henry Ford
Gumpy is offline   Reply With Quote
Old 02-25-2013, 11:40 AM   #18
LSJUNIPER
Senior Member
 
Join Date: Aug 2011
Location: CT
Posts: 215
Default Re: Flathead project

Thanks for all of the advise, Marvel mystery oil, OK will do. The cylinders mic out at 3.06 dia. Will keep you all posted on my progress. Mart I will figure out a better way to prop the motor. For now was thinking of supporting the end opposite the stand with a saw horse???

Last edited by LSJUNIPER; 02-25-2013 at 11:57 AM.
LSJUNIPER is offline   Reply With Quote
Old 02-25-2013, 12:56 PM   #19
Mart
Senior Member
 
Mart's Avatar
 
Join Date: May 2010
Location: Solihull, England.
Posts: 8,733
Default Re: Flathead project

3.06? sounds like a 221 cu in motor at 3-1/16" on a standard bore. Plenty more meat in that one if you want to go bigger. Early days yet, most important thing to be looking for is cracks. Check all around the head faces and around the bottom of the block on the sump face and inside and outside the block around the sump face.

Can't recommend anything re extra support as I can't guarantee what will work. (But anything is better than nothing)

Mart.
Mart is offline   Reply With Quote
Old 02-25-2013, 03:09 PM   #20
trainguy
Senior Member
 
trainguy's Avatar
 
Join Date: May 2010
Location: Lehighton Pa
Posts: 1,085
Default Re: Flathead project

Quote:
Originally Posted by Walt Dupont--Me. View Post
Hey GM. I remember that, it was a nice summer day. You and your wife and a friend of mine, we set in lawn chairs in from my shop and had great visit. I remember you drove in my drive and got out, opened the hood and pointed you heat gun at everything under the hood,it was running as cool a clam with Ships pumps, 6 bladded fan, shrould. Stop in again when you go to Nova Scotia. Walt
Not being form New England,just exactly how" cool is a clam"[just for the record.LOL Phil
trainguy is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 10:45 AM.