Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 02-23-2019, 08:47 PM   #1
FordTudor1931
Member
 
FordTudor1931's Avatar
 
Join Date: Nov 2015
Location: Grand Haven, MI
Posts: 95
Default Turn signal problems

Signalstat 900, cowl lights, stop lights turn signals. This is the set up. The turn signals work great if the brakes are not applied. The flasher hesitates and comes back to operation slowly when the brakes are applied with the bulbs never lightning fully. Why would this be? The system is 6 volt positive ground with a generator with electronic cutout and Tom W voltage regulator.


What's going on here?
FordTudor1931 is offline   Reply With Quote
Old 02-23-2019, 09:15 PM   #2
Patrick L.
Senior Member
 
Patrick L.'s Avatar
 
Join Date: May 2010
Location: Largo Florida
Posts: 7,225
Default Re: Turn signal problems

So it seems the turns and brakes work normal, they just don't work well together ?

I'll assume you're using a 535 flasher. Have you tried another/different one? The old ones are the best, the new ones are pretty much junk.
Patrick L. is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 02-23-2019, 09:28 PM   #3
GRutter
Senior Member
 
GRutter's Avatar
 
Join Date: Sep 2017
Location: Mint Hill, North Carolina
Posts: 386
Default Re: Turn signal problems

Not sure how your car is wired.
You also didn't state if this is a new problem and they were previously working correctly, or if this is a new install you are trying to get working.
Attached are the original Signal Stat wiring diagrams. You will need a Signal Stat 904 or 905 to use the same bulbs for turn and stop.
Hope this helps.
Attached Images
File Type: jpg turn_sig-1a.jpg (46.7 KB, 68 views)
File Type: jpg turn_sig-2a.jpg (52.2 KB, 48 views)
GRutter is offline   Reply With Quote
Old 02-23-2019, 09:40 PM   #4
FordTudor1931
Member
 
FordTudor1931's Avatar
 
Join Date: Nov 2015
Location: Grand Haven, MI
Posts: 95
Default Re: Turn signal problems

This is not a new problem, there were a lot more important things to address when I got the car, but it is now time to address this issue. I have tried a couple of different flashers (535) with no change.
FordTudor1931 is offline   Reply With Quote
Old 02-24-2019, 11:14 AM   #5
Badpuppy
Senior Member
 
Join Date: Dec 2017
Location: Guthrie, OK
Posts: 1,140
Default Re: Turn signal problems

Weak battery? Does the problem go away when the generator is charging? Could also be bad terminal connections between voltage supply and X terminal at the flasher. Best place to connect the fuse is at the generator side of the firewall junction box. Use a B-crimper or solder terminals at the wire ends to prevent corrosion.

What's happening is the opposite brake lamp draws about 3 amps, which will reduce available voltage from the battery alone, but should work ok with your regulated generator in operation. Just keep at fast idle while sitting at stop lights.
Badpuppy is offline   Reply With Quote
Old 02-24-2019, 03:15 PM   #6
FordTudor1931
Member
 
FordTudor1931's Avatar
 
Join Date: Nov 2015
Location: Grand Haven, MI
Posts: 95
Default Re: Turn signal problems

Sponsored Links (Register now to hide all advertisements)
Thanks Badpuppy for your suggestions. I hadn't thought about the power source and that is where I will start the corrective measures.
FordTudor1931 is offline   Reply With Quote
Old 02-24-2019, 05:34 PM   #7
Patrick L.
Senior Member
 
Patrick L.'s Avatar
 
Join Date: May 2010
Location: Largo Florida
Posts: 7,225
Default Re: Turn signal problems

I use the same setup as you [ except the electronic cutout ]with no issues.

Have had some flasher issues, old NOS unit solved the problems.

A poor connection could well be the problem too.

The Signal-stat 900 is a good unit. The unit itself should be grounded, I use a ground wire.
Patrick L. is offline   Reply With Quote
Old 02-24-2019, 09:21 PM   #8
CT Jack
Senior Member
 
CT Jack's Avatar
 
Join Date: May 2010
Location: Hebron, CT
Posts: 430
Default Re: Turn signal problems

It appears your brake switch might be the culprit. Your explanation of how everything works fine until you engage the brake switch says to me the brake switch has a high resistance connection. This condition is drawing down the voltage thereby preventing the flasher to work properly and dimming the lights. I would install a new brake switch. If you have a properly working voltage regulator, the directionals with the brake switch on should all work at idle. If your brake switch is okay then I would try to adjust the voltage regulator output at idle.
CT Jack is offline   Reply With Quote
Old 02-24-2019, 09:27 PM   #9
Tom Wesenberg
Senior Member
 
Tom Wesenberg's Avatar
 
Join Date: May 2010
Location: Mpls, MN
Posts: 27,582
Default Re: Turn signal problems

Do you have LED brake lights?
They will reduce the current draw a considerable amount and might be the answer to your problem.
Tom Wesenberg is offline   Reply With Quote
Old 02-25-2019, 10:14 AM   #10
Badpuppy
Senior Member
 
Join Date: Dec 2017
Location: Guthrie, OK
Posts: 1,140
Default Re: Turn signal problems

Quote:
Originally Posted by Tom Wesenberg View Post
Do you have LED brake lights?
They will reduce the current draw a considerable amount and might be the answer to your problem.
Great idea but the 535 won't work with them unless you add parallel resistors, which draw more current than the original bulbs. And I haven't found a 6V electronic flasher I'd want to live with.

10 CP (10W) bulbs in the cowl lamps may be enough to drive the 535 flasher, but idk.
Badpuppy is offline   Reply With Quote
Old 02-25-2019, 02:42 PM   #11
Patrick L.
Senior Member
 
Patrick L.'s Avatar
 
Join Date: May 2010
Location: Largo Florida
Posts: 7,225
Default Re: Turn signal problems

The 10 CP bulbs will allow the 535 to work.
Patrick L. is offline   Reply With Quote
Old 02-25-2019, 08:00 PM   #12
FordTudor1931
Member
 
FordTudor1931's Avatar
 
Join Date: Nov 2015
Location: Grand Haven, MI
Posts: 95
Default Re: Turn signal problems

No, I don't have LED brake lights. Would a combination of LED brake lights and regular cowl bulbs create enough resistance to allow the 535 flasher to work? If it would work, it would be a simple and elegant solution.
FordTudor1931 is offline   Reply With Quote
Old 02-26-2019, 12:18 AM   #13
RB_Nielsen
Member
 
RB_Nielsen's Avatar
 
Join Date: Feb 2017
Location: Iowa City, IA
Posts: 84
Default Re: Turn signal problems

There is an electronic - solid state - turn signal switch that does exactly what you are looking for that runs on 6V or 12V, LED or incandescent, works both brake and turn signal lights correctly, and is automatic self-cancelling. It's a higher-priced system but well worth the investment because being modern solid state it is literally set-and-forget. All the wiring + the SS module are easily hidden out of sight. I purchased the toggle switch version a few years ago.



@ http://www.turnswitch.com/Turnsignal.htm
RB_Nielsen is offline   Reply With Quote
Old 02-26-2019, 07:55 AM   #14
Patrick L.
Senior Member
 
Patrick L.'s Avatar
 
Join Date: May 2010
Location: Largo Florida
Posts: 7,225
Default Re: Turn signal problems

Quote:
Originally Posted by FordTudor1931 View Post
No, I don't have LED brake lights. Would a combination of LED brake lights and regular cowl bulbs create enough resistance to allow the 535 flasher to work? If it would work, it would be a simple and elegant solution.


Nope. Change the cowls to 10CP [ I can't remember the bulb number but there was a list here recently] and then it'll work. The front turns will be brighter too.
Patrick L. is offline   Reply With Quote
Old 02-26-2019, 09:40 AM   #15
Badpuppy
Senior Member
 
Join Date: Dec 2017
Location: Guthrie, OK
Posts: 1,140
Default Re: Turn signal problems

Quote:
Originally Posted by RB_Nielsen View Post
The Electro-Tech is undoubtedly the best way to go, but we're looking for remedies for the Signal-Stat already installed.

The vendors sell a 10CP bulb (actually 10 watts) that is the brightest bulb that will fit in the cowl lamp housing. 10W @ 6V is 1.67A, which may or may not draw enough current through the flasher heater to make it operate.
Badpuppy is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 03:24 AM.