Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 11-14-2017, 01:32 PM   #1
W1964
Junior Member
 
Join Date: Feb 2017
Location: Nacogdoches TX
Posts: 24
Default Need Source for engine part common to 35-48

I need an Adapter (fuel pump mounting) pn 48 9415. It is mounted on the rear of the intake manifold. The fuel pump is attached to it and the oil filler/breather cap is on top. It's illustration is on page 214 of the "green book" and the pn is shown on page 420. Can you point me in the right direction? Thanks a lot. Bill
W1964 is offline   Reply With Quote
Old 11-14-2017, 01:57 PM   #2
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 6,037
Default Re: Need Source for engine part common to 35-48

Bill, These are all over places like eBay. I think Drake makes them as well.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 11-14-2017, 02:35 PM   #3
supereal
Senior Member
 
supereal's Avatar
 
Join Date: Jul 2014
Location: Iowa
Posts: 1,440
Default Re: Need Source for engine part common to 35-48

Be aware that the fuel pump push rod must match the stand. The main difference is whether the intake manifold is cast iron or aluminum. Aluminum type is 7.87", and the iron is 8.87", and are not interchangeable.
supereal is offline   Reply With Quote
Old 11-14-2017, 03:16 PM   #4
W1964
Junior Member
 
Join Date: Feb 2017
Location: Nacogdoches TX
Posts: 24
Default Re: Need Source for engine part common to 35-48

Is the only difference the length of the rod?
Thank you.
W1964 is offline   Reply With Quote
Old 11-14-2017, 04:05 PM   #5
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 6,037
Default Re: Need Source for engine part common to 35-48

Quote:
Originally Posted by W1964 View Post
Is the only difference the length of the rod?
Thank you.
Just to clarify - the stands are the same height. The intake manifold makes the difference in which rod is required. As stated in the previous post, the factory aluminum intake requires the (1") shorter rod than the cast iron intake.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 11-14-2017, 05:23 PM   #6
Terry,OH
Senior Member
 
Terry,OH's Avatar
 
Join Date: May 2010
Posts: 3,481
Default Re: Need Source for engine part common to 35-48

If your looking for 48-9415 as it was produced in 35 it is not reproduced. Ford changed the part appearance and did not change the part number. The later part is available as a reproduction and many originals are for sale on auction sites and retailers. The originals are a much heavier die cast without an embossed ring above the area where the fuel pump mounts as in the photo below.
Attached Images
File Type: jpg 35 fuel pump adaptor.jpg (39.7 KB, 29 views)
Terry,OH is offline   Reply With Quote
Old 11-14-2017, 06:31 PM   #7
Mac VP
Senior Member
 
Mac VP's Avatar
 
Join Date: May 2010
Location: Cincinnati, OH
Posts: 1,117
Default Re: Need Source for engine part common to 35-48

We have good used originals in stock if you don’t find one out there
__________________
VANPELT SALES LLC
Cincinnati, Ohio
Office: 513-724-9486
www.vanpeltsales.com
www.classictransmission.com
Mac VP is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 11:12 PM.