Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 04-26-2020, 03:41 PM   #1
Werner
Senior Member
 
Werner's Avatar
 
Join Date: Jan 2019
Location: Germany, near Aachen
Posts: 1,151
Default Bad rod bearing

Bad evening!

Today we made the first big drive after reversing the engine & gear. I'm unlucky with my car! A bearing damage is in the offing. The engine knocks increasingly louder. With the stethoscope I hear the loudest point on cylinder 2 on the oil pan. Does it make sense / is it possible to try to replace the connecting rod without removing the engine? Only the head and the pan away?
__________________
Beste Gruesse aus Deutschland,
Werner


Ford Model A, Roadster, 1928
Citroen 11 CV, 1947
Hercules W 2000, 1976; (with NSU-Wankel Rotary Engine), Canadian version
Werner is offline   Reply With Quote
Old 04-26-2020, 03:45 PM   #2
J Franklin
Senior Member
 
J Franklin's Avatar
 
Join Date: May 2010
Location: Oregon
Posts: 5,946
Default Re: Bad rod bearing

Just remove the pan first and inspect.
J Franklin is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 04-26-2020, 06:15 PM   #3
Synchro909
Senior Member
 
Synchro909's Avatar
 
Join Date: Jun 2014
Location: Melbourne, Australia
Posts: 7,471
Default Re: Bad rod bearing

If it is a bad rod bearing, you can easily identify which one by shorting out the spark plugs one at a time. When the noise stops, that is the cylinder with the problem. Then, drop the sump and take off the head. The rod can be removed and replaced without removing anything more. I did it on a friend's car one day on the side of the road.
__________________
I'm part of the only ever generation with an analogue childhood and a digital adulthood.
Synchro909 is offline   Reply With Quote
Old 04-26-2020, 09:38 PM   #4
Flathead
Senior Member
 
Flathead's Avatar
 
Join Date: May 2010
Location: Southern Maine
Posts: 1,492
Default Re: Bad rod bearing

As long as the crank journal isn't damaged.
Flathead is offline   Reply With Quote
Old 04-27-2020, 05:06 AM   #5
Werner
Senior Member
 
Werner's Avatar
 
Join Date: Jan 2019
Location: Germany, near Aachen
Posts: 1,151
Default Re: Bad rod bearing

Hallo und guten Tag.
I get to lay down under the car this afternoon and remove the oil pan to open the bearing shells.

Then we'll see.
__________________
Beste Gruesse aus Deutschland,
Werner


Ford Model A, Roadster, 1928
Citroen 11 CV, 1947
Hercules W 2000, 1976; (with NSU-Wankel Rotary Engine), Canadian version
Werner is offline   Reply With Quote
Old 04-27-2020, 06:47 AM   #6
Synchro909
Senior Member
 
Synchro909's Avatar
 
Join Date: Jun 2014
Location: Melbourne, Australia
Posts: 7,471
Default Re: Bad rod bearing

Sponsored Links (Register now to hide all advertisements)
Quote:
Originally Posted by Flathead View Post
As long as the crank journal isn't damaged.
I should have mentioned that!
__________________
I'm part of the only ever generation with an analogue childhood and a digital adulthood.
Synchro909 is offline   Reply With Quote
Old 04-27-2020, 07:56 AM   #7
Jack Shaft
BANNED
 
Join Date: Dec 2019
Posts: 1,196
Default Re: Bad rod bearing

Id pull the engine if it was mine,work standing up,clean and position the engine for installing the pan correctly. It takes longer but youre work is easier and the results will better.
Jack Shaft is offline   Reply With Quote
Old 04-27-2020, 09:55 AM   #8
Hoovercw
Member
 
Join Date: Mar 2017
Location: Memphis, TN
Posts: 63
Default Re: Bad rod bearing

I have done it. Required removing the pan and head. You will need a ring compressor to get the piston back in. I tried doing everything through the bottom at first but i couldn't get enough room to take the wrist pin out. Others may have had more luck. The trick is finding another rod on the cheap and keeping the oil pump in place while putting the pan back on.
Hoovercw is offline   Reply With Quote
Old 04-27-2020, 11:35 AM   #9
johnneilson
Senior Member
 
Join Date: Jun 2010
Location: 34.22 N 118.36 W
Posts: 1,043
Default Re: Bad rod bearing

Werner,

If you can hear it in the pan, it may just be the dipper making contact with the tray.
Pull the pan and look for a mark.
__________________
As Carroll Smith wrote; All Failures are Human in Origin.
johnneilson is offline   Reply With Quote
Old 04-27-2020, 11:58 AM   #10
Jim Brierley
Senior Member
 
Join Date: Jun 2010
Location: Temecula, CA
Posts: 4,066
Default Re: Bad rod bearing

Gutten tag Werner,

I agree with John, check the rod hitting the pan first. If it is the rod bearing clearance, the babbitt might be able to be adjusted by shim removal?
Jim Brierley is offline   Reply With Quote
Old 04-27-2020, 02:19 PM   #11
Werner
Senior Member
 
Werner's Avatar
 
Join Date: Jan 2019
Location: Germany, near Aachen
Posts: 1,151
Default Re: Bad rod bearing

Guten Abend.

Thank you all for anticipations.

1) There are bearing damages. The flanks of the soft metal bearing shells have chipped off on the outer edge. Z 2 the damage goes up to 1/4 in the area. That was the cylinder that pounded loudly.
What can the edge chipping come from?

2) Can someone explain why the babbit clearance is set with the shims? The supporting hydrodynamic lubricating film is interrupted by the gap.


The surface of the crankshaft is o. k.
Attached Images
File Type: jpg P1020997.JPG (86.8 KB, 217 views)
File Type: jpg P1020998.JPG (82.8 KB, 192 views)
File Type: jpg P1020999.JPG (88.0 KB, 229 views)
File Type: jpg P1020964.JPG (111.0 KB, 216 views)
File Type: jpg P1020967 - Kopie.JPG (107.0 KB, 211 views)
__________________
Beste Gruesse aus Deutschland,
Werner


Ford Model A, Roadster, 1928
Citroen 11 CV, 1947
Hercules W 2000, 1976; (with NSU-Wankel Rotary Engine), Canadian version
Werner is offline   Reply With Quote
Old 04-27-2020, 02:32 PM   #12
J Franklin
Senior Member
 
J Franklin's Avatar
 
Join Date: May 2010
Location: Oregon
Posts: 5,946
Default Re: Bad rod bearing

The damage shown should not cause an audible knock in my thinking. Knock is caused by too much clearance or a mechanical interference. What was the clearance measured on these bearings?
J Franklin is offline   Reply With Quote
Old 04-27-2020, 04:27 PM   #13
johnneilson
Senior Member
 
Join Date: Jun 2010
Location: 34.22 N 118.36 W
Posts: 1,043
Default Re: Bad rod bearing

Just a suggestion, take the rods and make sure they are straight.
It may just be the picture, but the rod looks loaded on the side that is babbitt is broken out of.

Do not worry about the shim gap between the cap and rod, the bearing is not pressure fed anyways.

John
__________________
As Carroll Smith wrote; All Failures are Human in Origin.
johnneilson is offline   Reply With Quote
Old 04-27-2020, 04:53 PM   #14
rotorwrench
Senior Member
 
rotorwrench's Avatar
 
Join Date: Jun 2010
Location: San Antonio, Texas
Posts: 16,367
Default Re: Bad rod bearing

The rods & caps are tinned prior to pouring babbitt. Sometimes they don't get a good tin job and the babbitt doesn't stick as well as it should. Even with everything well coated a bearing can experience cracking & chipping of the babbitt if the bearings are well worn or the babbitt is thin.

Shimming is done for several reasons. The most common reason is to be able to tighten a worn bearing set by removing a shim or shims. The other reason is that folks had a tendency to sand the parting surface the cap on a flat piece of glass if the shims were all gone instead of exchanging them for a rebuilt set. This makes the next babbitt job too thin so more shims have to be used to keep from hitting steel while cutting the bores to size.

Last edited by rotorwrench; 04-27-2020 at 05:20 PM.
rotorwrench is offline   Reply With Quote
Old 04-27-2020, 06:35 PM   #15
Bob C
Senior Member
 
Join Date: May 2010
Location: So Cal
Posts: 8,711
Default Re: Bad rod bearing

Shouldn't the grooves in the bearings be cut like the ones in Herm's picture?
Attached Images
File Type: jpg Giles 338.jpg (28.6 KB, 137 views)
Bob C is offline   Reply With Quote
Old 04-27-2020, 09:11 PM   #16
Jack Shaft
BANNED
 
Join Date: Dec 2019
Posts: 1,196
Default Re: Bad rod bearing



Hydrodynamic lift principle occurs 90 degrees from the bearing shims..if the rod turns out to be true I've seen where folks have dabbled a little solder in the blown out area and dressed it off with good results
Jack Shaft is offline   Reply With Quote
Old 04-28-2020, 11:32 AM   #17
Jim Brierley
Senior Member
 
Join Date: Jun 2010
Location: Temecula, CA
Posts: 4,066
Default Re: Bad rod bearing

Guten morgan Werner,
Shims were always installed when new, by Ford, in order for the owner to be able to adjust the clearance as miles were accumulated. This was particularly needed in Model T's as they had no oil directly into the rod bearings. You might try carefully adding solder to the thrust (sides) of the bearings and hand filing to fit. Your bearings look to be still serviceable. Grooves such as you have were mostly used in pressured oiling systems, but yours, IMO, are better than the standard big X grooves as the have more surface area, and are obviously getting adequate amounts of oil.
Jim Brierley is offline   Reply With Quote
Old 04-28-2020, 12:09 PM   #18
rotorwrench
Senior Member
 
rotorwrench's Avatar
 
Join Date: Jun 2010
Location: San Antonio, Texas
Posts: 16,367
Default Re: Bad rod bearing

When the dippers hit that puddle of oil in the dipper tray, there is pressure to the oil that injects in there with each revolution. There is no way to measure it but it does get a good squirt each time. The higher the rpm, the higher the pressure. The X shaped grooves spread a more even flow of oil over the whole journal than a single groove can.

If the rod bearings still have a usable clearance, a person would need to check the center main journal. They take a beating compared to the others and they will knock if the clearance is too much.

A person would have to get all the oil off of an area that they want to try to solder. Even with flux, it's hard to get it to tin so the stuff would stick.

Last edited by rotorwrench; 04-28-2020 at 12:19 PM.
rotorwrench is offline   Reply With Quote
Old 04-28-2020, 03:42 PM   #19
Werner
Senior Member
 
Werner's Avatar
 
Join Date: Jan 2019
Location: Germany, near Aachen
Posts: 1,151
Default Re: Bad rod bearing

Hallo und guten Abend.

I measure a bearing clearance of 0.03 / 0.04 / 0.01 / 0.005 mm (millimeters!). The crank pins are clean and smooth. One has a tiny scar like a cut fingernail. (s. picture).
The cylinders (honing marks) and the slotted-jacket pistons are in a good condition and have modern piston rings (1 nose ring) with no vertical clearance play.

I am considering whether it is feasible to solder the damage of the one of the connecting rods on the tread with SN 40? Who has done this? -


The problem with the shim gap is that the hydrodynamic lubricating film, which has an average thickness of only 0.003 mm (3 µm), is interrupted. In order for the hydrodynamics to work properly, a trouble-free (= smooth) 360 ° course must always be guaranteed. This is independent of pressure pump oil.
Attached Images
File Type: jpg P1020942.JPG (107.0 KB, 107 views)
File Type: jpg P1030038.JPG (84.1 KB, 99 views)
__________________
Beste Gruesse aus Deutschland,
Werner


Ford Model A, Roadster, 1928
Citroen 11 CV, 1947
Hercules W 2000, 1976; (with NSU-Wankel Rotary Engine), Canadian version
Werner is offline   Reply With Quote
Old 04-28-2020, 05:14 PM   #20
rotorwrench
Senior Member
 
rotorwrench's Avatar
 
Join Date: Jun 2010
Location: San Antonio, Texas
Posts: 16,367
Default Re: Bad rod bearing

This link is for a similar question: https://www.practicalmachinist.com/v...epairs-207306/

There is a maybe on solder but a person would want as much tin as possible. The connecting rods are a lot easier to rebuild than the blocks. I know your in an area where there aren't a lot of Model A rebuilders but there may be someone close to you that can work babbitt for general purposes. The rods can be poured again and each one fit to your crank as needed or just refit the bad one if you want. It would last a lot longer than way.
rotorwrench is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 08:05 AM.