|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
02-03-2014, 01:02 PM | #1 |
Member
Join Date: Jun 2013
Location: Westchester ny
Posts: 68
|
king pin/spindle interference
Guys
I have attached 5 photos showing the top of the king pins in relation to the brake adjusting nut. On the passenger side the clearence is about a 1/4 ". On the driver side I barely have room to get dental floss through. 2 pictures are close ups and 2 are the overview of each side. This for the experts to look for other things wrong that might be causing this. I have touched / replaced almost everything in the front end, including the king pins, with all the pieces, although 25 years ago when the internet was not available. i did not serach the threads because I assumed this never came up before, since in all my readings, I never saw it. Thanks in advance Tom |
02-03-2014, 02:10 PM | #2 |
Senior Member
Join Date: May 2010
Location: Gwynn's Island Va
Posts: 1,386
|
Re: king pin/spindle interference
Bearing under king pin is wrong. Too thick.
Thats what it looks like. |
Sponsored Links (Register now to hide all advertisements) |
|
02-03-2014, 04:41 PM | #3 |
Senior Member
Join Date: Dec 2010
Location: FRESNO, CA
Posts: 12,560
|
Re: king pin/spindle interference
I would "think" that if it at least had some clearance, it wouldn't be a "BIG DEAL" or cause any "ill" effect.???
Bill W.
__________________
"THE ASSISTANT GURU OF STUFF" |
02-03-2014, 07:11 PM | #4 |
Member
Join Date: Jun 2013
Location: Westchester ny
Posts: 68
|
Re: king pin/spindle interference
The bolt is through the king pin in the only location it can go. .
That puts the top of the spindle / king pin in a set location. That what has me puzzled. Is it something in the wheel hub? I don't believe the bushing would set the top higher. Bill I'm not having any trouble, but it caught my eye while greasing. Will clean the grease off everything when the weather warms up. No heat in the garage |
02-03-2014, 07:29 PM | #5 |
Senior Member
Join Date: May 2010
Location: Portland OR
Posts: 6,340
|
Re: king pin/spindle interference
Clean and look is a good plan. Looking I see what looks like two different bearings. But without being clean can't see how the parts fit in relation to each other.
|
02-03-2014, 07:30 PM | #6 |
Member
Join Date: Jul 2012
Location: New Hampshire
Posts: 62
|
Re: king pin/spindle interference
Sponsored Links (Register now to hide all advertisements)
|
02-03-2014, 07:57 PM | #7 |
Senior Member
Join Date: Jun 2010
Location: Perry OH
Posts: 1,330
|
Re: king pin/spindle interference
The part on the backing plate where the brake adjuster goes through looks bent down in picture #2. The other side looks OK. JMO.
|
02-03-2014, 08:38 PM | #8 |
Senior Member
Join Date: May 2010
Posts: 3,099
|
Re: king pin/spindle interference
I don't know why Dudley's reply was pulled but I believe he was correct. I think if you measure the distance from the square adjuster to the top of the kingpin they will be nearly equal. The adjuster housings are different (early vs. late).
__________________
http://www.abarnyard.com/ |
02-03-2014, 08:55 PM | #9 |
Senior Member
Join Date: May 2010
Posts: 136
|
Re: king pin/spindle interference
Tom, slightly off topic but I would be careful with those oddball shocks. A friend recently had a scare when a brake rod got hung up on a non-stock shock. He had been driving trouble free for several years beforehand.
|
02-03-2014, 09:03 PM | #10 |
Member
Join Date: Jun 2013
Location: Westchester ny
Posts: 68
|
Re: king pin/spindle interference
Marco
I don't understand what you mean....Dudley's response pulled. Also I don't understand where to measure. Square adjusting nut to top of king pins differ by a fat 1/4" from pass side to driver side. I'm starting to think the housings are different since the king pins are in a set position........I think |
02-03-2014, 09:20 PM | #11 | |
Senior Member
Join Date: May 2010
Posts: 3,099
|
Re: king pin/spindle interference
Quote:
__________________
http://www.abarnyard.com/ |
|
02-03-2014, 09:39 PM | #12 |
Senior Member
Join Date: May 2010
Location: Mpls, MN
Posts: 27,582
|
Re: king pin/spindle interference
I see an air gap on top of the axle on the right side. A thinner bearing (or worn bearing) would let the axle and kingpin drop down some.
|
02-04-2014, 10:24 AM | #13 |
Senior Member
Join Date: May 2010
Location: Fresno, Ca.
Posts: 3,636
|
Re: king pin/spindle interference
|
02-04-2014, 01:00 PM | #14 | |
Senior Member
Join Date: May 2010
Location: Fresno, Ca.
Posts: 3,636
|
Re: king pin/spindle interference
Quote:
At the time I deleted my post, I also noted, which looks like, a space between the axle and the spindle......on the bottom side. You agree.... |
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|