Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 10-12-2017, 02:02 AM   #1
wingski
Senior Member
 
wingski's Avatar
 
Join Date: Jul 2017
Location: Cave Junction, Oregon
Posts: 432
Default starts but won't run

OK, I need help. I have done everything I can think of get my A running. However, it starts immediately but won’t keep running without missing and back-firing. I’ll list the things I’ve done and maybe you can tell me where I went wrong.

1-New fresh gas is in the tank. Filled tank to 1/2 full.
2-Installed new headgasket, used Indian Chief shellac, and torqued to 55 ft. Lbs in three stages and then torqued in reverse order.
3-Ran compression check- #1 56 psi #2 53 psi #3 55 psi and #4 60 psi.
4-Removed timing gear cover and the notch in the crank gear lined up with the dimple in the cam gear.
5-Made sure the cam plunger and spring were good. They were new.
6-Drilled out dimple enough so timing pin fits securely when in hole and bolted cover back on.
7-Set distributor so rotor was pointed at #1, set the point to .020 and spark plugs to .035, and backed up the distributor cam so the points just closed while the timing hole in the cam gear was lined up with the timing pin.
8- Turned timing pin around and turned crank back from timing mark and turned crank forward. Points sparked when rotor was pointed at #1.
9-Made sure gas was getting to the carb
10-Checked plug wires for continuity. They are good.
11-Tightened all intake, exhaust, and carb mounts. No air leaks.
12-Made sure gas cap was venting correctly. It is.
13-Turned key on, retarded spark, pulled throttle lever down two clicks, opened rich/lean knob 1/2 turn, pulled out choke, and pushed starter.
14-Engine started immediately, but never smoothed out when I pushed the choke in. I pulled the choke back when the engine tried to stall, but all it did was back-fire and finally stalled when I pushed the choke in.
15- I tried starting it three different times allowing 15-20 minutes between attempts. The results were the same or close to the same each time.

I don’t mind asking for advice, but I really hate to ask for help because I’m soo stuborn. However, I’m at wits end with this thing.

Mike
wingski is offline   Reply With Quote
Old 10-12-2017, 03:18 AM   #2
Craggles
Junior Member
 
Craggles's Avatar
 
Join Date: Sep 2017
Location: Queensland
Posts: 9
Default Re: starts but won't run

Maybe a manifold air leak or sticky valves. I believe the auto trans fluid or mmo in the oil can relieve sticky valves, a oil flush did the trick for mine.
Craggles is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 10-12-2017, 04:31 AM   #3
SuperDave
Senior Member
 
SuperDave's Avatar
 
Join Date: Jul 2010
Location: Melbourne Fl
Posts: 166
Default Re: starts but won't run

try opening the GAV another turn. Sounds like it's too lean.
__________________
Live in the Past.... It's cheaper.
SuperDave is offline   Reply With Quote
Old 10-12-2017, 06:32 AM   #4
Glen in Hillman MI
Senior Member
 
Join Date: May 2010
Posts: 107
Default Re: starts but won't run

Check strainer in carburetor ? Check gas flow with strainer out, gas line could be in too far.
Glen
Glen in Hillman MI is offline   Reply With Quote
Old 10-12-2017, 06:36 AM   #5
Jacksonlll
Senior Member
 
Jacksonlll's Avatar
 
Join Date: Jul 2012
Location: Michigan-- Member of Oakleaf of MARC
Posts: 1,686
Send a message via ICQ to Jacksonlll
Default Re: starts but won't run

Try a different condenser. You have a higher probability of a new one being bad than a good one going bad. Make sure of the timing. The coil fires when the points open. Use a light and go by the book.
Jacksonlll is offline   Reply With Quote
Old 10-12-2017, 07:55 AM   #6
Tom Wesenberg
Senior Member
 
Tom Wesenberg's Avatar
 
Join Date: May 2010
Location: Mpls, MN
Posts: 27,582
Default Re: starts but won't run

Sponsored Links (Register now to hide all advertisements)
Quote:
Originally Posted by SuperDave View Post
try opening the GAV another turn. Sounds like it's too lean.
X2
Mine needs to be open 1 1/2 turns for a couple minutes.
As soon as the engine starts, pull the spark lever half way down.
Tom Wesenberg is offline   Reply With Quote
Old 10-12-2017, 08:25 AM   #7
Sunnybrook Farm
Senior Member
 
Sunnybrook Farm's Avatar
 
Join Date: Oct 2015
Location: Virginia
Posts: 409
Default Re: starts but won't run

Was it running and then acted up or are you trying to get it started for the first time?
Sunnybrook Farm is offline   Reply With Quote
Old 10-12-2017, 08:42 AM   #8
barkleydave
Senior Member
 
barkleydave's Avatar
 
Join Date: Oct 2014
Location: Kentucky
Posts: 502
Default Re: starts but won't run

No mention of Carburetor in your check list? Assuming timing is correct or close... they will run even if off 10 degrees retarded. When was the carb gone through? Keep digging you will find the it.
barkleydave is offline   Reply With Quote
Old 10-12-2017, 09:10 AM   #9
Big hammer
Senior Member
 
Join Date: Jun 2014
Location: Land of Lincoln
Posts: 3,114
Default Re: starts but won't run

Mike mentioned fuel to the carb, he didn't say fuel in the carb :-(
__________________
Don't force it with a little hammer tap, tap, tap
get a bigger hammer tap done
Big hammer is offline   Reply With Quote
Old 10-12-2017, 10:21 AM   #10
katy
Senior Member
 
katy's Avatar
 
Join Date: Jun 2015
Location: Red Deer, Alberta
Posts: 5,004
Default Re: starts but won't run

Pull the throttle lever down a bit more.
__________________
If you don't hear a rumor by 10 AM, start one!.
Got my education out behind the barn!
katy is offline   Reply With Quote
Old 10-12-2017, 10:30 AM   #11
700rpm
Senior Member
 
700rpm's Avatar
 
Join Date: May 2010
Location: Portland, Oregon
Posts: 5,892
Default Re: starts but won't run

I suspect a fuel problem. Make certain neither end of your fuel line is pushed too far in, which would restrict gas flow. Also make sure your sediment bowl is not full or clogged.
__________________
Ray Horton, Portland, OR


As you go through life, keep your eye on the donut, not the hole.
700rpm is offline   Reply With Quote
Old 10-12-2017, 10:42 AM   #12
abachman3
Senior Member
 
abachman3's Avatar
 
Join Date: Jun 2013
Location: Western Springs, IL
Posts: 323
Default Re: starts but won't run

When it runs better with the choke pulled out (Closed) this suggests a lack of fuel. As mentioned above, try starting with the GAV opened more, at least a full turn or slightlt more.
abachman3 is offline   Reply With Quote
Old 10-12-2017, 11:10 AM   #13
wingski
Senior Member
 
wingski's Avatar
 
Join Date: Jul 2017
Location: Cave Junction, Oregon
Posts: 432
Default Re: starts but won't run

Quote:
Originally Posted by Craggles View Post
Maybe a manifold air leak or sticky valves. I believe the auto trans fluid or mmo in the oil can relieve sticky valves, a oil flush did the trick for mine.
I have a MMO jar with the oil in it mounted on the firewall, but I don't know how to use it. I don't want to use that Marvel stuff until I figure out how much to open the valve on the dispenser. I would think that my compression values would show that the valves are working correctly, but who knows?
wingski is offline   Reply With Quote
Old 10-12-2017, 12:10 PM   #14
wingski
Senior Member
 
wingski's Avatar
 
Join Date: Jul 2017
Location: Cave Junction, Oregon
Posts: 432
Default Re: starts but won't run

Quote:
Originally Posted by 700rpm View Post
I suspect a fuel problem. Make certain neither end of your fuel line is pushed too far in, which would restrict gas flow. Also make sure your sediment bowl is not full or clogged.
Ray, I’ve been told by several different members that the fuel line ( in my case, fuel lines) could be pushed in too far, but I don’t see how. I’ve attached a photo of the front carb because I’ve got the back carb diconnected from the fuel line with the choke wired all the way closed. I’m hoping that if it is a carb problem I can get it running on the one and work from there.

I appreciate your advice and wish I didn’t live so far away from someone who really knows A’s.

Thanks again,
Mike
Attached Images
File Type: jpg carborator 1 (800x600).jpg (302.9 KB, 97 views)
wingski is offline   Reply With Quote
Old 10-12-2017, 12:17 PM   #15
1crosscut
Senior Member
 
1crosscut's Avatar
 
Join Date: Feb 2011
Location: Lincoln, Nebraska
Posts: 1,905
Default Re: starts but won't run

Answering the question in post #7 could possibly help with diagnosis.
__________________
Dave / Lincoln Nebraska
1crosscut is offline   Reply With Quote
Old 10-12-2017, 12:22 PM   #16
George Miller
Senior Member
 
George Miller's Avatar
 
Join Date: May 2010
Location: NC
Posts: 2,975
Default Re: starts but won't run

Quote:
Originally Posted by wingski View Post
Ray, I’ve been told by several different members that the fuel line ( in my case, fuel lines) could be pushed in too far, but I don’t see how. I’ve attached a photo of the front carb because I’ve got the back carb diconnected from the fuel line with the choke wired all the way closed. I’m hoping that if it is a carb problem I can get it running on the one and work from there.

I appreciate your advice and wish I didn’t live so far away from someone who really knows A’s.

Thanks again,
Mike
are you saying you have two carbs? If so it is another ball game.
George Miller is offline   Reply With Quote
Old 10-12-2017, 12:34 PM   #17
40 Deluxe
Senior Member
 
Join Date: May 2010
Location: now Kuna, Idaho
Posts: 3,774
Default Re: starts but won't run

I haven't read all of your posts on this matter, but one thing caught my eye on your timing. You mentioned turning the points cam to where the points just closed. It should be to where the points just start to open with the rotor pointing to #1. This is just an initial setting. Actual timing is set by the spark lever on the steering column.
Is this a rebuild that has not run yet, or are you reviving an engine that has sat for awhile? If it was running before, leave the timing alone. That does not change from just sitting.
If you're trying to get it running on just one carb, remove the other one and make a block-off plate to cover the intake port. Just make a gasket or shim without the center opening and put the carb back on. Otherwise the engine can suck air around the throttle shaft and plate, through the float bowl, etc. and make the back cylinders lean.
Your carb fitting does not appear to have a line going into the carb so no problem there.
40 Deluxe is offline   Reply With Quote
Old 10-12-2017, 01:50 PM   #18
wingski
Senior Member
 
wingski's Avatar
 
Join Date: Jul 2017
Location: Cave Junction, Oregon
Posts: 432
Default Re: starts but won't run

The car came with the dual Tillotsons, and the previous owner never got it running for more than a minute or so. I have the original Zenith and manifold and both are in good shape, but I’d like to get this thing running with the Tillotsons to see if they actually add 10 hp. If you really feel that this is a carb problem, I can put the old Zenith back on. Those Tillotsons look really good, but are worthless if they won’t give me a smooth running engine.

Mike
wingski is offline   Reply With Quote
Old 10-12-2017, 01:56 PM   #19
Bill G
Senior Member
 
Bill G's Avatar
 
Join Date: Jun 2017
Location: Walla Walla, WA
Posts: 1,044
Default Re: starts but won't run

Quote:
Originally Posted by wingski View Post
The car came with the dual Tillotsons, and the previous owner never got it running for more than a minute or so. I have the original Zenith and manifold and both are in good shape, but I’d like to get this thing running with the Tillotsons to see if they actually add 10 hp. If you really feel that this is a carb problem, I can put the old Zenith back on. Those Tillotsons look really good, but are worthless if they won’t give me a smooth running engine.

Mike
Maybe that would be a good starting point just to see if the problem can be isolated to the fuel/carburetor system.
Bill G is offline   Reply With Quote
Old 10-12-2017, 01:59 PM   #20
Bill G
Senior Member
 
Bill G's Avatar
 
Join Date: Jun 2017
Location: Walla Walla, WA
Posts: 1,044
Default Re: starts but won't run

Besides, if you don't have the original to compare the dual carb to, how will you actually know the difference?
Bill G is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 04:29 AM.