|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
07-14-2020, 04:00 PM | #1 |
Senior Member
Join Date: Jan 2012
Location: New Jersey
Posts: 1,423
|
Re-torque head nuts
I had to pull three studs due to leaking. I cleaned, resealed and installed them back in the block. The heads are still on the motor.
My question is how do I torque these down? Should I torque them in steps? 45,50,55? Should I torque all the head studs in sequence again? (I already did my five hot/cold cycles, five because of the supercharger and manufacturers recommendation). Do I simply re-torque these straight up to 55 lbs? The stud are #1, #10 and #13 Thank you, Joe Last edited by jrvariel48; 07-14-2020 at 05:03 PM. |
07-14-2020, 04:23 PM | #2 |
Senior Member
Join Date: May 2010
Location: Solihull, England.
Posts: 8,750
|
Re: Re-torque head nuts
I don't know if there is an official procedure.
Gut feeling tells me that I would torque directly to the previously torqued value. Straight to 55 lbs ft. But then make sure these get rechecked over three or more heat cycles. (check them all). I just keep checking them all until nothing moves any more. Mart. |
Sponsored Links (Register now to hide all advertisements) |
|
07-14-2020, 07:32 PM | #3 |
Senior Member
Join Date: Sep 2016
Location: sydney australia
Posts: 1,033
|
Re: Re-torque head nuts
my thoughts follow the factory sequence cant go wrong if its tight it wont move and you've checked all the rest at the same time
|
07-15-2020, 12:57 PM | #4 |
Senior Member
Join Date: May 2010
Location: Long Island, NY
Posts: 1,052
|
Re: Re-torque head nuts
Hi Joe, hope all's well?
You still battling the stud leaks? No need to retorque single studs in steps, just go straight to the necessary torque (55#) Thanks, Gary in N.Y. P.S Did you get the pan gasket (dipstick) OK. Went out of here a while back! I sent a little heavier one to you.
__________________
http://www.stromberg-bulletin.com/me...berg-equipped/ |
07-15-2020, 04:16 PM | #5 | |
Senior Member
Join Date: Jan 2012
Location: New Jersey
Posts: 1,423
|
Re: Re-torque head nuts
Quote:
|
|
07-17-2020, 07:21 PM | #6 |
Senior Member
Join Date: Jan 2012
Location: New Jersey
Posts: 1,423
|
Re: Re-torque head nuts
Sponsored Links (Register now to hide all advertisements)
Last edited by jrvariel48; 07-17-2020 at 07:22 PM. Reason: Spelling |
07-17-2020, 07:38 PM | #7 |
Senior Member
Join Date: May 2010
Location: albany
Posts: 465
|
Re: Re-torque head nuts
I use teflon hi temp thread sealer from napa. Fuel and antifreeze resistant and works great
|
07-17-2020, 07:58 PM | #8 |
Senior Member
Join Date: May 2010
Location: Charlotte NC KiWi-L100 available here
Posts: 2,960
|
Re: Re-torque head nuts
Joe for lord knows how many years all I ya used is 3m weatherstrip cement on a kazillion chevs & flatheads head studs or any stud/ bolt in water jackets with zero issues.
Cheers TP |
07-18-2020, 05:07 AM | #9 | |
Senior Member
Join Date: Jan 2012
Location: New Jersey
Posts: 1,423
|
Re: Re-torque head nuts
Quote:
Thanks |
|
07-18-2020, 05:07 AM | #10 |
Senior Member
Join Date: Jan 2012
Location: New Jersey
Posts: 1,423
|
Re: Re-torque head nuts
|
07-18-2020, 06:03 AM | #11 |
Senior Member
Join Date: May 2010
Location: Charlotte NC KiWi-L100 available here
Posts: 2,960
|
Re: Re-torque head nuts
Yellow or black in tube.
|
07-18-2020, 01:27 PM | #12 |
Senior Member
Join Date: Jan 2012
Location: New Jersey
Posts: 1,423
|
Re: Re-torque head nuts
|
07-25-2020, 12:50 PM | #13 |
Senior Member
Join Date: Jan 2012
Location: New Jersey
Posts: 1,423
|
Re: Re-torque head nuts
Well I tried the Permatex high temp with teflon and they still leak as bad as they did originally. I'm going to try Kiwi's idea with the 3M weatherstrip adhesive.
Am I missing something here?? The first time I used Permatex Aviation and just lightly snugged the studs in the block. The second time I hand tighten. Anyone want to chime In??? Third times a charm |
07-25-2020, 01:00 PM | #14 |
Senior Member
Join Date: Apr 2019
Location: Kansas
Posts: 921
|
Re: Re-torque head nuts
The trouble with thread sealers is that they are typically made to seal tapered threads (pipe threads). What is needed on a straight thread (like a stud going to water) is a sealer that "sets up" or "cures". I like to use a good brand of RTV silicone on the threads and lightly snug the studs into the block. The threads on studs and block must be scrupulously clean and bone dry when installing,and a few hours without water on the back sides to cure. They never leak,and come out easily next time.
Alternately, loctite blue (242) can be used as well. It will be a bit harder to remove next time but will seal well. Terry
__________________
"It don't take but country smarts to solve the problem" (Smokey Yunick) '41 Merc Town Sedan / 260" 8CM engine '66 Fairlane four door / "warmed up" 302 |
07-25-2020, 04:11 PM | #15 |
Senior Member
Join Date: Jan 2012
Location: New Jersey
Posts: 1,423
|
Re: Re-torque head nuts
Thank you Terry!
Last edited by jrvariel48; 07-25-2020 at 04:11 PM. Reason: spelling |
07-25-2020, 04:14 PM | #16 |
Senior Member
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,936
|
Re: Re-torque head nuts
I have found this sealant to work EXCELLENTLY. Bought this at O'Reilly's.
|
07-25-2020, 04:14 PM | #17 |
Senior Member
Join Date: Jan 2012
Location: New Jersey
Posts: 1,423
|
Re: Re-torque head nuts
I friend stopped over today and noticed the studs were still dripping after the car was turned off for about 10 minutes. I'm running an aftermarket radiator that came with a 16lb. cap. Could this be a pressure issue?? I ordered a 7lb. cap which was the lowest I could find.
|
07-25-2020, 05:06 PM | #18 |
Senior Member
Join Date: Jan 2012
Location: New Jersey
Posts: 1,423
|
Re: Re-torque head nuts
|
07-25-2020, 10:17 PM | #19 | |
Member Emeritus
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
|
Re: Re-torque head nuts
Quote:
|
|
07-26-2020, 09:57 AM | #20 | |
Senior Member
Join Date: Jan 2012
Location: New Jersey
Posts: 1,423
|
Re: Re-torque head nuts
Quote:
I can run it all day with the electric fan on at a steady 190*. The temp hasn't gone past 190* even when it was 94*outside and I was driving it hard for an hour. I put the 7lb. cap on this morning before a ride. When I turned off the car, only three out of five were dripping. So I'm not really sure what's going on yet. Still running straight water at the moment until this is straightened out. I'm still going to pull the leaking studs, clean and reinstall with Permatex Thread sealant with PTFE Thanks |
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|