Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 01-06-2017, 10:45 AM   #1
Tgibby
Junior Member
 
Join Date: Mar 2016
Location: Zephyrhills,Fl.
Posts: 20
Default rear axle nut torque

I have 41 Ford super deluxe trying to find information for rear axle nut torque
Tgibby is offline   Reply With Quote
Old 01-06-2017, 10:54 AM   #2
deuce_roadster
Senior Member
 
deuce_roadster's Avatar
 
Join Date: Oct 2011
Location: Shelton, WA
Posts: 3,777
Default Re: rear axle nut torque

It is high, very high like around 200 ft lbs. I never try to take it up that high in 1 pull. I tighten it up pretty tight, (leave cotter pin out) drive around the block, tighten again. I do that a couple of times to work the hub onto the taper. Then when it is REALLY tight, I put a torque wrench on it and take it to 195 ft lbs and then the next cotter hole and install cotter.
It is the friction of the taper of the axle and the hub that keeps the hub from spinning on the axle NOT the key. If the hub is loose enough that the axle key is driving the car, you will eventually brake the end off the axel as a crack will develop at the inner end of the axle key recess.
deuce_roadster is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 01-06-2017, 11:18 AM   #3
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
Default Re: rear axle nut torque

Quote:
Originally Posted by deuce_roadster View Post
it is high, very high like around 200 ft lbs. I never try to take it up that high in 1 pull. I tighten it up pretty tight, (leave cotter pin out) drive around the block, tighten again. I do that a couple of times to work the hub onto the taper. Then when it is really tight, i put a torque wrench on it and take it to 195 ft lbs and then the next cotter hole and install cotter.
It is the friction of the taper of the axle and the hub that keeps the hub from spinning on the axle not the key. If the hub is loose enough that the axle key is driving the car, you will eventually brake the end off the axel as a crack will develop at the inner end of the axle key recess.
perfect (accurate) advice.
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 01-06-2017, 11:45 AM   #4
deuce_roadster
Senior Member
 
deuce_roadster's Avatar
 
Join Date: Oct 2011
Location: Shelton, WA
Posts: 3,777
Default Re: rear axle nut torque

Thanks Mike!
I forgot to mention that I also take a sharpie and draw a line on the end of the axle so I know where the cotter hole is located.
deuce_roadster is offline   Reply With Quote
Old 01-06-2017, 12:47 PM   #5
PeterC
Senior Member
 
PeterC's Avatar
 
Join Date: May 2010
Location: Connecticut
Posts: 855
Default Re: rear axle nut torque

Quote:
Originally Posted by deuce_roadster View Post
Thanks Mike!
I forgot to mention that I also take a sharpie and draw a line on the end of the axle so I know where the cotter hole is located.
Reminds me of when I owned a 1966 Big Block Corvette with real knock-off wheels. If not torqued right they would come off the car at speed! Needless to say I was a perfectionist at setting to torque specs and then adding safety tape to each spinner to watch for any movement. Every time I went for a ride I would perform a "preflight" inspection to monitor those wheels! Never had a mishap!
PeterC is offline   Reply With Quote
Old 01-06-2017, 02:32 PM   #6
JM 35 Sedan
Senior Member
 
JM 35 Sedan's Avatar
 
Join Date: May 2010
Location: Near Rising Sun, Maryland
Posts: 10,856
Default Re: rear axle nut torque

Sponsored Links (Register now to hide all advertisements)
Here's a good recent post that explains what can happen if the axle nuts are not properly torqued. deuce_roadster has already given good advice on how to correctly torque the axle nuts.

https://www.fordbarn.com/forum/showth...ear+axle+shaft
__________________
John

"Never give up on what you really want to do. The person with big dreams is more powerful than one with all the facts". Albert Einstein
JM 35 Sedan is offline   Reply With Quote
Old 01-07-2017, 02:13 PM   #7
fordv8j
Senior Member
 
fordv8j's Avatar
 
Join Date: Jan 2015
Posts: 322
Default Re: rear axle nut torque

Dick Flynn said 150#...then tighten till the cotter pin lines up....don't back off
fordv8j is offline   Reply With Quote
Old 01-07-2017, 07:10 PM   #8
36coupe
Senior Member
 
36coupe's Avatar
 
Join Date: Oct 2012
Location: Eastcoast
Posts: 859
Default Re: rear axle nut torque

After I had to change an axle since the threads stripped, i spent a bunch of time cleaning the surfaces and lapping the axle to the drum to ensure a good fit.
I also fabbed up a set of drum retainers in case the axle ever breaks.
36coupe is offline   Reply With Quote
Old 01-08-2017, 08:24 PM   #9
psogden
Member
 
Join Date: Apr 2013
Location: Auburn, CA
Posts: 86
Default Re: rear axle nut torque

I've been through the axle torque issue. There are differing views. I''m passing on this one from a FB member given to me as "just his opinion" & I choose not to identify him. I think his view has a lot of credibility, however. Here it is:



I would think the purpose of the initial torque which seems to be very high, is to set the axle and hub tapers tight enough to keep them together. Once this has been accomplished, a lesser torque value would be sufficient to keep the hub from loosening on the axle. After the cotter key has been placed the nut is not going to move whether the torque is 225 or 125. I would go back to the super clean fitment between axle and hub tapers and their exact angle degrees to be of the utmost importance. Do not take any of this to the bank! Just my thoughts at this time
psogden is offline   Reply With Quote
Old 01-08-2017, 10:39 PM   #10
JM 35 Sedan
Senior Member
 
JM 35 Sedan's Avatar
 
Join Date: May 2010
Location: Near Rising Sun, Maryland
Posts: 10,856
Default Re: rear axle nut torque

Quote:
Originally Posted by psogden View Post
Update. Cleaned axle threads a bit using Blue Point tool. Then, using correct 5/8” - 18 good used Ford nuts obtained from unidentified source, was able to torque both rear drums to 175 FPs. As suggested by John (JM 35 Sedan), will drive the car a bit, then add 10 FPs repeating until I reach 200. Thanks again to everybody for your input.
psogden, just wondering if you have taken the axle nut torque on your car any higher than 175 ft lbs?
__________________
John

"Never give up on what you really want to do. The person with big dreams is more powerful than one with all the facts". Albert Einstein
JM 35 Sedan is offline   Reply With Quote
Old 01-09-2017, 10:10 AM   #11
Planojc
Senior Member
 
Planojc's Avatar
 
Join Date: May 2010
Location: Plano, Texas
Posts: 828
Default Re: rear axle nut torque

As been said, always clean the axle taper and hub of any grease.
Planojc is offline   Reply With Quote
Old 01-09-2017, 12:32 PM   #12
Tgibby
Junior Member
 
Join Date: Mar 2016
Location: Zephyrhills,Fl.
Posts: 20
Default Re: rear axle nut torque

Thanks for info.Appreciate it
Tgibby is offline   Reply With Quote
Old 01-20-2020, 04:19 PM   #13
[email protected]
Junior Member
 
Join Date: Dec 2019
Location: Rockville Maryland
Posts: 3
Default Re: rear axle nut torque

Ford Model A Rear Axle Specifications
Type: Three Quarter Floating

Material: Special Ford Carbon Manganese Steel

Gear Ratios:

3.78:1
3.70:1 (early 28’s)
3.54:1
4.11:1
Bearings:

Rear Wheel:
O.D. of Axle Housing Race – 2.061″ to 2.0635″
I.D. of Wheel Hub 3.188″ to 3.190″ – Max Wear 3.185″
Pinion Bearing:
Timken 28156 (2 each) – Double Taper Roller Type
Bearing Cup: Timken 28317
Ring Gear:

8.4″ Pitch Diameter
1 3/16″ Wide Teeth
Axle Shaft:

1 1/8″ Diameter
1.128″-1.130″ at Wheel Bearing
Dimension From Housing Flange to bearing Shoulder in Axle Housing:

Before 1929: 1.370″ to 1.372″
After: 1.365″ to 1.367″
Axle and Drive Shaft Seal: CR 10926

Rear Axle Seal: CR 20112, Victor 49024

Differential Lube: 600W to 160W

Differential Oil Capacity: 2 1/4 Pint

Torque Specs:

Axle Nut Torque: 100 ft/lbs
INEX1@EROLS.COM is offline   Reply With Quote
Old 01-20-2020, 04:21 PM   #14
Mart
Senior Member
 
Mart's Avatar
 
Join Date: May 2010
Location: Solihull, England.
Posts: 8,732
Default Re: rear axle nut torque

I'm not going to say that is wrong but I believe it should be much higher than 100 ft/lbs.
Mart is offline   Reply With Quote
Old 01-20-2020, 04:49 PM   #15
Kerk
Senior Member
 
Join Date: May 2010
Posts: 642
Default Re: rear axle nut torque

As a teen I remember it well ! NO brakes at ALL - FOOT PEDAL WEMT TO THE F;OOR -- EMERGENCY ALL THE WAY UP. - SHUT OFF AND WAITED FOR IT TO STOP !! I was lucky - no traffic and just to go, pick up the fender skirt . Car resting on the tire on the fender bead !! Car was a 48 Mercury Convertible. kerk
Kerk is offline   Reply With Quote
Old 01-20-2020, 04:59 PM   #16
Tinker
Senior Member
 
Tinker's Avatar
 
Join Date: May 2010
Location: MN
Posts: 7,053
Default Re: rear axle nut torque

I just picked up a 50-250# torque wrench to do the wheelbearing on my brothers 08 chevy truck. Torque was like 200plus. Wrench wasn't cheap but if a shop did the wheelbearings it would have cost a few hundred past that.

Story not really helpful here but,... I do think most places like autozone lend tools out for free. Torque wrenches included.


Link lifted from the Model A forum right here on the barn. Model A Ford 100-125#

https://www.fordbarn.com/forum/showt...xle+nut+torque



.

Last edited by Tinker; 01-20-2020 at 05:35 PM.
Tinker is offline   Reply With Quote
Old 01-20-2020, 05:30 PM   #17
JSeery
Member Emeritus
 
JSeery's Avatar
 
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
Default Re: rear axle nut torque

Take a look at a the torque value chart, even a grade #2 5/8-18 bolt/nut recommend torque value dry is 115 ft-lbs. And Ford axles are not grade #2 equivalent by a long shot.

Torque Values (dry) for:

Grade #5 bolt/nut - 180 ft-lbs
Grade #7 bolt/nut - 210 ft-lbs
Grade #8 bolt/nut - 240 ft-lbs

Ford axles and axle nuts are high quality/grade parts.
Attached Images
File Type: jpg Torque Values.jpg (74.6 KB, 35 views)

Last edited by JSeery; 01-20-2020 at 05:59 PM.
JSeery is offline   Reply With Quote
Old 01-20-2020, 05:32 PM   #18
Hal Beatty
Senior Member
 
Hal Beatty's Avatar
 
Join Date: Jul 2012
Location: Bellingham, WA
Posts: 213
Default Re: rear axle nut torque

For me, 100-125 lbs/ft isn't tight enough for a V8 axle.

200-220 lbs/ft according to Service Letter mentioned in an old V-8 Times; then follow duece roadster's advice... do not exceed 275 lbs/ft when lining up for the cotter pin.
Hal Beatty is offline   Reply With Quote
Old 01-20-2020, 08:28 PM   #19
frnkeore
Senior Member
 
frnkeore's Avatar
 
Join Date: Jul 2019
Location: Southern Oregon
Posts: 782
Default Re: rear axle nut torque

Let me tell you a little story about the pre 48 axle nuts.

When I was 18 (1963), my best friend had a 32, chopped and channeled, 5 window coupe, with a 326 CI Olds and a 4-71 blower on top of it. It had a 37 LaSalle trans and a 4500# Hays clutch connected to the rear axle.

We were street racers and after George got the blower, almost every race, we would shear a key. After the 3rd key, we put a 4 ft, pipe wrench on that nut. I can't tell you how much torque, a 150 lb kid put on the nut (150x4ft = 600 ft #, I'd say at least 350 ft#) but, the nut and threads did not strip. At the very next race, the key stayed but, we broke the axle!!!

This picture is after that. We put a Olds rear end and 4 speed hydro behind it.
Attached Images
File Type: jpg George Coupe.jpg (60.2 KB, 62 views)
__________________
Frank
'35 Ford Model 51
'48 Ford F3
'54 Ford Tudor Mainline
frnkeore is offline   Reply With Quote
Old 01-21-2020, 01:46 PM   #20
Init1
Senior Member
 
Init1's Avatar
 
Join Date: May 2010
Location: Oregon City, Oregon
Posts: 208
Default Re: rear axle nut torque

250 ft. Lbs. And back off until you can insert the cotter pin. Make sure the fine threads are clean and good.
Init1 is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 08:52 AM.