Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 02-22-2011, 05:06 PM   #1
Ryan
Administrator
 
Ryan's Avatar
 
Join Date: Apr 2010
Location: Austin, TX
Posts: 577
Default Fleathead Engine Stands



You know what I got a thing for? Flathead engine stands... But I know absolutely nothing about them. I'm betting some of you fellas know everything there is to know about them. ... To read the rest of this blog entry from The Ford Barn, click here.
Ryan is offline   Reply With Quote
Old 02-22-2011, 05:21 PM   #2
Mark Slight
Senior Member
 
Mark Slight's Avatar
 
Join Date: May 2010
Location: Dixon, CA
Posts: 473
Default Re: Fleathead Engine Stands

Almost every Ford dealership had one or more of these engine stands made by K-R Wilson. Who was one of the major suppliers of equipment to Ford dealers at the time 30's to 50's as I remember.

They are very heavy and safe to work with, now days expensive and expensive to ship. Well worth the investment if you are going to do several engines or more. Could be a club project.

Mark
Mark Slight is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 02-22-2011, 06:38 PM   #3
Ken/Alabama
Senior Member
 
Ken/Alabama's Avatar
 
Join Date: May 2010
Location: Alabama
Posts: 2,239
Default Re: Fleathead Engine Stands

I have 2 of the K.R. Wilson engine stands like the one pictured. One has the base and the other does not. I am looking for a base . If push comes to shove I could fabricate one out of heavy gauge steel. Makes working on a flathead V-8 or V-12 nice. The whole engine can be assembled exept for the exhaust manifold.
Ken/Alabama is offline   Reply With Quote
Old 02-22-2011, 06:40 PM   #4
Glenn Thoreson
Senior Member
 
Glenn Thoreson's Avatar
 
Join Date: May 2010
Posts: 171
Default Re: Fleathead Engine Stands

K.R. Wilson X-6000 engine stand. I wish I had one. These are the only thing that will provide a safe, secure stand to work on the flathead engines.
Glenn Thoreson is offline   Reply With Quote
Old 02-22-2011, 08:43 PM   #5
MattStrube
Member
 
MattStrube's Avatar
 
Join Date: May 2010
Location: Austin, TX
Posts: 32
Default Re: Fleathead Engine Stands

I love those things...and have been thinking about picking up an old kr Wilson catalogue so I can check out more of their stuff to put on my wishlist. Wondering what catalogue would have the most flathead v8 related items?
MattStrube is offline   Reply With Quote
Old 02-22-2011, 08:52 PM   #6
sikopal
Junior Member
 
Join Date: May 2010
Location: Londonderry VT
Posts: 11
Default Re: Fleathead Engine Stands

Quote:
Originally Posted by Glenn Thoreson View Post
K.R. Wilson X-6000 engine stand. I wish I had one. These are the only thing that will provide a safe, secure stand to work on the flathead engines.
True, the KR Wilson is a solid stand but not the "only" one, Clayborne built a solid stand for the flathead engine that works well!
Will post a photo of mine later!
sikopal is offline   Reply With Quote
Old 03-07-2011, 02:29 PM   #7
Glenn Thoreson
Senior Member
 
Glenn Thoreson's Avatar
 
Join Date: May 2010
Posts: 171
Default Re: Fleathead Engine Stands

Quote:
Originally Posted by sikopal View Post
True, the KR Wilson is a solid stand but not the "only" one, Clayborne built a solid stand for the flathead engine that works well!
Will post a photo of mine later!
Actually, according to the list of suggested shop tools in a war time Canadian Ford publication, the stand shown in the original picture is probably made by Wasco. The tool number X-6000 is listed as a Wasco engine stand, and matches the picture in the book.
Glenn Thoreson is offline   Reply With Quote
Old 02-22-2011, 08:41 PM   #8
Roadster62
Senior Member
 
Roadster62's Avatar
 
Join Date: May 2010
Location: Ridgefield, Ct
Posts: 3,399
Default Re: Fleathead Engine Stands

Question #1 does a Flathead block weigh less than the stand?
Roadster62 is offline   Reply With Quote
Old 02-22-2011, 09:23 PM   #9
FlatheadTed
Senior Member
 
FlatheadTed's Avatar
 
Join Date: May 2010
Location: Auckland
Posts: 4,073
Send a message via AIM to FlatheadTed
Default Re: Fleathead Engine Stands

This one mounts on the exhaust manifold a lot of modern ones mount on the bell housing and the engines have been known to brake of .That is the engine bell housing can crack ,This job has the 16 holes for when you are doing a valve job ,A nice piece to have in your Flat-head shop .
__________________
http://www.flatheadted.com
FlatheadTed is offline   Reply With Quote
Old 02-22-2011, 10:44 PM   #10
Flathead Fever
Senior Member
 
Flathead Fever's Avatar
 
Join Date: May 2010
Location: Yucaipa, CA
Posts: 599
Default Re: Fleathead Engine Stands

I have a KRW stand that is missing the parts tray and the base.

According to the 1940 KRW catalog they had sold 14,000 of them in the last 20 years. In the catalog the base looks like it was an option, also the base in the 1940 catalog is not cast like the one in the picture, it is made from a 30X30X1/4 steel plate. The tool tray is also different.
Attached Images
File Type: jpg KRW #2.jpg (52.6 KB, 449 views)
File Type: jpg KRW #4.jpg (228.0 KB, 340 views)
File Type: jpg KRW #1.jpg (54.8 KB, 426 views)
File Type: jpg KRW #3.jpg (65.9 KB, 375 views)

Last edited by Flathead Fever; 02-22-2011 at 10:50 PM.
Flathead Fever is offline   Reply With Quote
Old 02-23-2011, 09:06 AM   #11
Rem/Mo
Member
 
Rem/Mo's Avatar
 
Join Date: May 2010
Location: N.W. Mo
Posts: 72
Default Re: Fleathead Engine Stands


Great thread and thanks for the pics.
I have one of those that I have beem trying to soak free to get the head to turn. I had no idea that there was a base for them. Looked like it would have to be fastened to the floor to be stable. It is good to see all the attachments that were available. I will have to be on the lookout for some of them. When I get mine loosened up and working I plan to mount an old flattie on it for display. It would be a good use for a cracked block that would have no other value.
Rem/Mo is offline   Reply With Quote
Old 02-23-2011, 07:50 AM   #12
John Kennedy
Senior Member
 
John Kennedy's Avatar
 
Join Date: May 2010
Location: Tucson Arizona
Posts: 301
Default Re: Fleathead Engine Stands

I converted a cheap-o 3 leg stand into a wide base 4 leg stand, and built the engine holder out of 1/4" plate drilled to bolt onto the exhaust ports. The plate is welded to a thick angle-cut tube that rotates in the stand.
Actually patterned after a HAMB post I found.
I can take pictures and post em up, if you'd like.

John
__________________
Building a 29 Sedan on 32 chassis........ very slowly....
John Kennedy is offline   Reply With Quote
Old 02-23-2011, 09:37 AM   #13
cbillelder
Senior Member
 
Join Date: May 2010
Posts: 870
Default Re: Fleathead Engine Stands

I've had one of these stands for about 40 years now. Mine also has the worm gear box for rotating the motor on the stand. Very nice! You can position the engine at any angle you want. It came with the cast square base, but I took it off and threw it away and built a T-shaped base from 4" channel. The square base was too wide to fit between the legs of my engine lift. This all happened 40 years ago. If I had known how valuable these bases were, I would have kept it!!
cbillelder is offline   Reply With Quote
Old 02-23-2011, 07:51 AM   #14
John Kennedy
Senior Member
 
John Kennedy's Avatar
 
Join Date: May 2010
Location: Tucson Arizona
Posts: 301
Default Re: Fleathead Engine Stands

The angle cut tube is what sets the engine level.
__________________
Building a 29 Sedan on 32 chassis........ very slowly....
John Kennedy is offline   Reply With Quote
Old 02-23-2011, 11:37 AM   #15
lowride
Senior Member
 
Join Date: May 2010
Location: roanoke, va
Posts: 137
Default Re: Fleathead Engine Stands

Here are two KR Wilsons, One with and one without a base. Then there's another that we made.
Attached Images
File Type: jpg DSC01940.JPG (44.6 KB, 451 views)
File Type: jpg DSC01941.JPG (43.0 KB, 402 views)
File Type: jpg DSC01942.JPG (63.3 KB, 524 views)
lowride is offline   Reply With Quote
Old 08-26-2011, 04:13 PM   #16
Dave27
Senior Member
 
Join Date: May 2011
Location: Snohomish,Wa.
Posts: 139
Default Re: Fleathead Engine Stands

Quote:
Originally Posted by lowride View Post
Here are two KR Wilsons, One with and one without a base. Then there's another that we made.
I like the one you made i need one like that for my spare motor.
Dave27 is offline   Reply With Quote
Old 02-23-2011, 11:50 AM   #17
Capn John
Senior Member
 
Capn John's Avatar
 
Join Date: May 2010
Location: BIRTHPLACE OF SPEED, FLORIDA
Posts: 531
Default Re: Fleathead Engine Stands

Stumpy's Fabrication Works makes adapters for a normal engine stand. the adapters bolts to the exhaust side of the block so you negate the chance of breaking the rear of the block. http://stumpysfabworks.zoomshare.com...and%20adapters
Capn John is offline   Reply With Quote
Old 03-27-2011, 01:26 PM   #18
Tman
Junior Member
 
Join Date: May 2010
Posts: 14
Default Re: Fleathead Engine Stands

Quote:
Originally Posted by Capn John View Post
Stumpy's Fabrication Works makes adapters for a normal engine stand. the adapters bolts to the exhaust side of the block so you negate the chance of breaking the rear of the block. http://stumpysfabworks.zoomshare.com...and%20adapters
I have a small run of these ready to weld that I am finally getting around to. $50 + shipping. The tube is 2 3/8" that fits most generic stands. Since these are unwelded I can customize them somewhat if you like before welding.



I will also ship these unwelded with longer tubes if that suits you better, same price. 3/8" plate, 12.5 punds for shipping wieght.

Not trying to spam, just cleaning shop and these might be handy for someone new to flatheads. I will donate a portion of each sale to Ryan for the cost of running the board.
Tman is offline   Reply With Quote
Old 05-13-2014, 09:03 PM   #19
Topsterguy
Senior Member
 
Topsterguy's Avatar
 
Join Date: May 2010
Location: Victoria BC Canada
Posts: 347
Default Re: Fleathead Engine Stands

Quote:
Originally Posted by Tman View Post
I have a small run of these ready to weld that I am finally getting around to. $50 + shipping. The tube is 2 3/8" that fits most generic stands. Since these are unwelded I can customize them somewhat if you like before welding.



I will also ship these unwelded with longer tubes if that suits you better, same price. 3/8" plate, 12.5 punds for shipping wieght.

Not trying to spam, just cleaning shop and these might be handy for someone new to flatheads. I will donate a portion of each sale to Ryan for the cost of running the board.
May 13 / 2014 You have a PM.
Topsterguy is offline   Reply With Quote
Old 05-13-2014, 09:06 PM   #20
Topsterguy
Senior Member
 
Topsterguy's Avatar
 
Join Date: May 2010
Location: Victoria BC Canada
Posts: 347
Default Re: Fleathead Engine Stands

Does anyone have an idea of the weight of a 49-53 block? I know the whole engine is 569 lbs but wondering what just the block is.
Topsterguy is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 10:22 AM.