Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 12-10-2020, 07:11 PM   #1
TJMack
Member
 
Join Date: Mar 2017
Location: Venice, Fl and Marcy, NY
Posts: 93
Default Simple to make and use Toe-In gauge

I was trying to figure out an easy way to check the toe-in on a friend’s model A to see if we could stop the “Death Wobble”. So I watched a couple YouTube videos and came up with an idea to make an inexpensive and simple to use toe-in gauge.

I’ve attached a few pictures so it should be pretty self explanatory. The gauge is put between the tires at the front of the car at the height determined by the chains, then a mark is put on the inner, sliding, PVC pipe in line with an index mark on the movable coupling. The car is then rolled FORWARD (as pointed out below) until the chains show the gauge is again at the same height from the ground,

Another mark is put on the sliding PVC pipe using the same index mark on the movable coupling. The distance between the marks is the toe-in, or toe-out.

You have to think about what you’re doing to make an adjustment. It get's confusing. Looking at the gauge when it is at the rear, and you are under the car, the second line you make has to be to the RIGHT of the first mark for it to be toe-in. If it is to the left, you have toe-out. Toe-in relaxes the gauge as the tires go the rear making the gauge longer, thus the mark will be to the right, and toe-out compresses the spring making the gauge shorter and the mark to the left..

The information you need to make one is as follows:
  • inner PVC pipe -- ¾” diameter 45” long (need end cap too)
  • outer PVC pipe -- 1” diameter 36” long (need end cap too)
  • cut a window in the outer pipe with a Dremel tool (location not critical)
  • cut a section out of a 1” PVC coupling so it will slide over the 1” pipe
    • scribe a mark on the coupling for a reference point
  • chain length -- 10”
    • to fit over ¼” diameter bolts through end caps. Allow to swing freely
    • Grind end of ¼” bolts to a point to hold to tire
  • spring from Ace hardware #SP-9713
  • put hole plug (Hillman # 139479 from Lowes) in end of ¾’ PVC
    • to support spring


    All for less than $20

    By the way; we found that the toe-in on the car was over ½’. After we adjusted it the “Death Wobble” is gone …… for now at least.
Attached Images
File Type: jpg 20201210_145008.jpg (233.4 KB, 250 views)
File Type: jpg 20201210_144854.jpg (36.1 KB, 219 views)
File Type: jpg 20201210_145345.jpg (42.0 KB, 243 views)
File Type: jpg 20201210_145404.jpg (34.2 KB, 207 views)
File Type: jpg 20201210_145421.jpg (38.5 KB, 192 views)

Last edited by TJMack; 12-11-2020 at 11:57 AM.
TJMack is offline   Reply With Quote
Old 12-10-2020, 08:24 PM   #2
Y-Blockhead
Senior Member
 
Y-Blockhead's Avatar
 
Join Date: Jul 2011
Location: Redondo Beach, CA
Posts: 5,817
Default Re: Simple to make and use Toe-In gauge

Quote:
Originally Posted by TJMack View Post
I was trying to figure out an easy way to check the toe-in on a friend’s model A to see if we could stop the “Death Wobble”. So I watched a couple YouTube videos and came up with an idea to make an inexpensive and simple to use toe-in gauge.

I’ve attached a few pictures so it should be pretty self explanatory. The gauge is put between the tires at the front of the car at the height determined by the chains, then a mark is put on the inner, sliding, PVC pipe in line with an index mark on the movable coupling. The car is then rolled backward until the chains show the gauge is again at the same height from the ground,
I always thought you rolled the car forward (direction of travel) when checking.

Last edited by Y-Blockhead; 12-10-2020 at 08:38 PM.
Y-Blockhead is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 12-10-2020, 08:40 PM   #3
Y-Blockhead
Senior Member
 
Y-Blockhead's Avatar
 
Join Date: Jul 2011
Location: Redondo Beach, CA
Posts: 5,817
Default Re: Simple to make and use Toe-In gauge

Quote:
Originally Posted by TJMack View Post
I was trying to figure out an easy way to check the toe-in on a friend’s model A to see if we could stop the “Death Wobble”. So I watched a couple YouTube videos and came up with an idea to make an inexpensive and simple to use toe-in gauge.

I’ve attached a few pictures so it should be pretty self explanatory. The gauge is put between the tires at the front of the car at the height determined by the chains, then a mark is put on the inner, sliding, PVC pipe in line with an index mark on the movable coupling.The car is then rolled backwarduntil the chains show the gauge is again at the same height from the ground,

Not to mention it would be kind of hard to roll the car backwards starting with the gauge at the front?
Y-Blockhead is offline   Reply With Quote
Old 12-11-2020, 02:39 AM   #4
lildave
Junior Member
 
lildave's Avatar
 
Join Date: Aug 2019
Posts: 10
Default Re: Simple to make and use Toe-In gauge

Or something like this.

https://www.lowrangeoffroad.com/diy-...-patterns.html


Sent from my iPhone using Tapatalk
lildave is offline   Reply With Quote
Old 12-11-2020, 05:32 AM   #5
Bruce of MN
Senior Member
 
Bruce of MN's Avatar
 
Join Date: May 2010
Location: VA
Posts: 1,395
Default Re: Simple to make and use Toe-In gauge

You could make something like that out of plywood and make sure the arms were long enough to match the radius of the spot where toe-in is measured.


Edit: I mean the tool in post #4

Last edited by Bruce of MN; 12-11-2020 at 05:20 PM.
Bruce of MN is offline   Reply With Quote
Old 12-11-2020, 06:56 AM   #6
bob from red oak
Member
 
bob from red oak's Avatar
 
Join Date: Jun 2016
Location: red oak texas
Posts: 65
Default Re: Simple to make and use Toe-In gauge

Sponsored Links (Register now to hide all advertisements)
Nice work! I'm always glad to see individuals come up with these kinds of helpful self-created things. It is especially pleasing to see it does not require a software app and a computer screen.
bob from red oak is offline   Reply With Quote
Old 12-11-2020, 07:35 AM   #7
Patrick L.
Senior Member
 
Patrick L.'s Avatar
 
Join Date: May 2010
Location: Largo Florida
Posts: 7,225
Default Re: Simple to make and use Toe-In gauge

Thats pretty much the same as the 100 yr old spring loaded gauge I have.
Patrick L. is offline   Reply With Quote
Old 12-11-2020, 07:46 AM   #8
desotoguy
Senior Member
 
Join Date: Nov 2011
Location: Greenwood SC
Posts: 293
Default Re: Simple to make and use Toe-In gauge

A very neat idea and tool you created. A couple of questions.
First to get the correct measurement for toe in, doesn't the gauge need to be at the center of the wheel at the height of the king pin for each measurement front and back?
Second, would you need to make more than one measurement check? As you adjust the tie rod you are changing the measured dimension at the front as well as the back of the wheels.
desotoguy is offline   Reply With Quote
Old 12-11-2020, 07:52 AM   #9
MrBruce
Senior Member
 
MrBruce's Avatar
 
Join Date: Oct 2014
Location: Charlotte, NC
Posts: 310
Default Re: Simple to make and use Toe-In gauge

That's interesting, I have the manufactured gauge and you put it on the front and move the car forward. It has a gauge that you read when it's rolled forward. I took a shower curtain rod that's already spring loaded put the chains on it and stuck it in the front, marked with a pencil when the two rods come together and then rolled it back and marked it again and then looked at the measurement and it gives you the reading. The gauge we bought for the club tool closet was around $120.00 although I've seen them for less. Great job making the one you did.
MrBruce is offline   Reply With Quote
Old 12-11-2020, 08:01 AM   #10
Chuck Kuntz
Senior Member
 
Join Date: May 2010
Posts: 13,620
Default Re: Simple to make and use Toe-In gauge

You can save money with the way I do it. Two common pins and a tape measure. Place pins in tire tread and measure back then roll forward and measure again. Does take the help of your wife or a friend. Total cost zero.
Chuck Kuntz is offline   Reply With Quote
Old 12-11-2020, 09:15 AM   #11
nkaminar
Senior Member
 
nkaminar's Avatar
 
Join Date: Jan 2012
Location: Western North Carolina
Posts: 3,820
Default Re: Simple to make and use Toe-In gauge

TJ, great post. Thanks. Neat tool.



The tow in needs to be measured at the same height front and back, thus the chains. It does not have to be at the same height of the hub but should be high enough to get a good reading.



If you adjust the camber, not easy on a Model A, or any other steering geometry, remember to check the tow in last as the other setting will change the tow in.
__________________
A is for apple, green as the sky.
Step on the gas, for tomorrow I die.
Forget the brakes, they really don't work.
The clutch always sticks, and starts with a jerk.
My car grows red hair, and flies through the air.
Driving's a blast, a blast from the past.
nkaminar is offline   Reply With Quote
Old 12-11-2020, 09:21 AM   #12
Afordman31
Senior Member
 
Afordman31's Avatar
 
Join Date: May 2010
Location: Michigan
Posts: 577
Default Re: Simple to make and use Toe-In gauge

This is the one I made, have posted it before. I use the pin method and have good results!
Attached Images
File Type: jpg DSC06538.jpg (56.0 KB, 104 views)
File Type: jpg DSC06541.jpg (44.6 KB, 92 views)
File Type: jpg DSC06544.jpg (76.3 KB, 106 views)
Afordman31 is offline   Reply With Quote
Old 12-11-2020, 11:25 AM   #13
KenBolton
Senior Member
 
Join Date: Jun 2020
Location: Fall Creek, WI
Posts: 210
Default Re: Simple to make and use Toe-In gauge

I think you did a great job. Thanks for sharing! An old alignment man told me to roll the car back and forth at least two car lengths after each adjustment and check again. Makes sense with these old less than perfect tolerance cars.
KenBolton is offline   Reply With Quote
Old 12-11-2020, 11:53 AM   #14
TJMack
Member
 
Join Date: Mar 2017
Location: Venice, Fl and Marcy, NY
Posts: 93
Talking Re: Simple to make and use Toe-In gauge

Yblockhead, you are correct. I misspoke. The car does need to roll forward after you install the gauge. My old mind reverses things occasionally. As I said, you have to think about what you are doing.


I hope someone gets some benefit out of it.
TJMack is offline   Reply With Quote
Old 12-11-2020, 01:15 PM   #15
Y-Blockhead
Senior Member
 
Y-Blockhead's Avatar
 
Join Date: Jul 2011
Location: Redondo Beach, CA
Posts: 5,817
Default Re: Simple to make and use Toe-In gauge

Quote:
Originally Posted by TJMack View Post
Yblockhead, you are correct. I misspoke. The car does need to roll forward after you install the gauge. My old mind reverses things occasionally. As I said, you have to think about what you are doing.


I hope someone gets some benefit out of it.
Haha, not a problem. Sometimes it is hard for us "Old Dudes" to know which end is up when we are laying under the car.

I like to see people make their own tools.
Y-Blockhead is offline   Reply With Quote
Old 12-12-2020, 02:20 PM   #16
Dick M
Senior Member
 
Dick M's Avatar
 
Join Date: May 2010
Location: Ukiah, CA
Posts: 477
Send a message via Yahoo to Dick M
Default Re: Simple to make and use Toe-In gauge

The measurement is between 1/16"-1/32" difference from back to front. I always think about a bent rim which will throw the measurement off. So, here is how I do it:

Drill a whole in a block of wood to tightly fit and hold a sharpie pen
Jack up one front wheel at a time just off of the floor
Place the sharpie in the block on the floor and the point of the sharpie to a flat spot close to the center of the tire
Turn the tire one revolution slowly with the sharpie against the tire creating a centerline
Take your measurements from the centerlines

This method will compensate for any runout from your rims

I have used this method several times with great success
Dick M is offline   Reply With Quote
Old 12-13-2020, 08:18 AM   #17
larry harding
Senior Member
 
Join Date: Sep 2015
Location: western n.c.
Posts: 392
Default Re: Simple to make and use Toe-In gauge

maybe i like things simple and crude, but here is what i did. a piece of 3/4 pvc with a cap on each end. tap one of the caps 1/4 20 and put in a screw 1 in. or more. put this in the front of the wheels and adjust the screw until it just touches. move the the back and the distance between the screw and the wheel is the toe in.
larry harding is offline   Reply With Quote
Old 12-13-2020, 08:37 AM   #18
nkaminar
Senior Member
 
nkaminar's Avatar
 
Join Date: Jan 2012
Location: Western North Carolina
Posts: 3,820
Default Re: Simple to make and use Toe-In gauge

The runout is an important thing to consider. It is also important to have the height where the measurements are taken the same front and back. The camber will effect the measurement if the height is not the same. As far as the runout is concerned, if the measurement is taken at the same point on the tire front and back the runout is taken out of the equation. That is what is nice about TJ's tool. The location does not change moving from front to back and the chains assure that the height remains constant. Using his tool or a similar one, make the measurements on a flat surface like a garage.
__________________
A is for apple, green as the sky.
Step on the gas, for tomorrow I die.
Forget the brakes, they really don't work.
The clutch always sticks, and starts with a jerk.
My car grows red hair, and flies through the air.
Driving's a blast, a blast from the past.
nkaminar is offline   Reply With Quote
Old 12-14-2020, 08:39 AM   #19
TJMack
Member
 
Join Date: Mar 2017
Location: Venice, Fl and Marcy, NY
Posts: 93
Talking Re: Simple to make and use Toe-In gauge

Quote:
Originally Posted by Dick M View Post
. I always think about a bent rim which will throw the measurement off.

You make an excellent point that got me thinking, and so is this one:




Quote:
Originally Posted by nkaminar View Post
As far as the runout is concerned, if the measurement is taken at the same point on the tire front and back the runout is taken out of the equation.

I said it was easy to make and use, not understand. :-)


Thanks for the input, Guys. I appreciate it all.
TJMack is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 12:38 AM.