Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 07-02-2019, 11:59 AM   #1
WABOOM
Senior Member
 
WABOOM's Avatar
 
Join Date: Jun 2018
Location: Minnesota
Posts: 347
Default Complete Wiring for '51 Mercury

I'm gonna be rewiring my Mercury in the fall. Could you give me suggestions on who to buy from?
Under the hood I'd like to use a factory reproduction for looks, but under the dash it can be regular wires. I've search to in haven't been able to find more than 2 suppliers.
Thank you
WABOOM is offline   Reply With Quote
Old 07-02-2019, 12:57 PM   #2
TJ
Senior Member
 
TJ's Avatar
 
Join Date: May 2010
Location: Napa,California
Posts: 6,005
Default Re: Complete Wiring for '51 Mercury

Quote:
Originally Posted by WABOOM View Post
I'm gonna be rewiring my Mercury in the fall. Could you give me suggestions on who to buy from?
Under the hood I'd like to use a factory reproduction for looks, but under the dash it can be regular wires. I've search to in haven't been able to find more than 2 suppliers.
Thank you
Why do you want to mix and match the wiring? If you are still 6 volt then buy the factory style harness. If you are 12 volt then use a panel and harness from American Auto Wire, Kwik Wire, etc. Either type of harness will come with instructions. You can do what you want, but mixing types of wiring never looks right and you better make a diagram after you are done so you can trace wires if there is a problem. You should also be fusing the critical circuits,
TJ is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 07-02-2019, 01:12 PM   #3
rotorwrench
Senior Member
 
rotorwrench's Avatar
 
Join Date: Jun 2010
Location: San Antonio, Texas
Posts: 16,367
Default Re: Complete Wiring for '51 Mercury

I haven't found any vendor that offers plastic coated wiring in correct colors for the mid century Mercury cars. Rhode Island Wire coats their fabric outer insulation cover so it will last longer than the OEM did but they aren't cheap. The others, like what Mac's sells, are less expensive but they don't coat the fabric insulator cover for each wire. They will likely last as long as the OEM which was around 20 years or so if not well kept. The wiring is a little bit larger in diameter than original and may have fit issues in tight places.

I have to warn folks that the harnesses sold for these cars are not always sold as a set. You have to buy the individual circuit harnesses and there are quite a few individual harnesses. You have to know he wiring pretty well before you order. I always suggest purchase of one of the large laminated circuit diagrams from flea-pay if they are still available. The new stuff comes with a diagram supplied for each harness they sell but only for that individual harness. Some cars have power accessories and some don't so this is why they sell the separate harnesses. Some folks only want to by one to repair the circuit that is problematic and not the whole car.
rotorwrench is offline   Reply With Quote
Old 07-02-2019, 01:27 PM   #4
supereal
Senior Member
 
supereal's Avatar
 
Join Date: Jul 2014
Location: Iowa
Posts: 1,634
Default Re: Complete Wiring for '51 Mercury

Often replacement harnesses contain several branches that may not be needed. This is to reduce the number of harnesses in the inventory. The best advice is to tag and identify each wire as it is disconnected. It is also helpful to take some photos of places with lots of connections, such as the dashboard and firewall, and make notes as you go. If the loom is not supplied with a wiring diagram, obtain one before you start. Otherwise, it is like taking a trip in a foreign country without a road map!
supereal is offline   Reply With Quote
Old 07-02-2019, 02:07 PM   #5
51 MERC-CT
Senior Member
 
51 MERC-CT's Avatar
 
Join Date: May 2010
Location: East Hartford, Ct
Posts: 5,898
Default Re: Complete Wiring for '51 Mercury

This is what I installed from Rhode Island wire works.
Most of the visible wire was replaced with the kit.
Any thing not visible was replaced with non covered wire.
Attached Images
File Type: jpg 1a RIWIRE.jpg (74.7 KB, 226 views)
__________________
DON'T RECALL DOING SOMETHING FOR MYSELF BASED ON SOMEONE ELSE'S LIKES OR DISLIKES
51 MERC-CT is offline   Reply With Quote
Old 07-02-2019, 02:57 PM   #6
tubman
Senior Member
 
tubman's Avatar
 
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,259
Default Re: Complete Wiring for '51 Mercury

Sponsored Links (Register now to hide all advertisements)
Are those prices correct? A little quick figgerin' in my head says about $2000.
tubman is offline   Reply With Quote
Old 07-02-2019, 03:26 PM   #7
slowforty
Senior Member
 
slowforty's Avatar
 
Join Date: May 2010
Location: Tinley Park Ill
Posts: 1,055
Default Re: Complete Wiring for '51 Mercury

https://www.classiccarwiring.com/
Try this site for a Nice wiring diagram
slowforty is offline   Reply With Quote
Old 07-02-2019, 03:34 PM   #8
51504bat
Senior Member
 
51504bat's Avatar
 
Join Date: Sep 2013
Location: SoCal-Redlands
Posts: 2,997
Default Re: Complete Wiring for '51 Mercury

Check out YnZ wiring in Redlands, CA High quality original looms that can be modified to your specifics if needed. Not cheap but quality costs money.
https://www.ynzyesterdaysparts.com
__________________
Making the simple complicated for over 30 years.
51504bat is offline   Reply With Quote
Old 07-02-2019, 06:50 PM   #9
flintstone
Senior Member
 
Join Date: May 2010
Posts: 3,346
Default Re: Complete Wiring for '51 Mercury

Yes YnZ have the best Mercury correct wire harness
flintstone is offline   Reply With Quote
Old 07-02-2019, 08:18 PM   #10
WABOOM
Senior Member
 
WABOOM's Avatar
 
Join Date: Jun 2018
Location: Minnesota
Posts: 347
Default Re: Complete Wiring for '51 Mercury

Thank you gentlemen
WABOOM is offline   Reply With Quote
Old 07-03-2019, 09:43 AM   #11
WABOOM
Senior Member
 
WABOOM's Avatar
 
Join Date: Jun 2018
Location: Minnesota
Posts: 347
Default Re: Complete Wiring for '51 Mercury

Can anyone recommend a 6 volt kit replacement wiring kit that is good quality? not the expensive fabric wire reproduction?
WABOOM is offline   Reply With Quote
Old 07-03-2019, 09:56 AM   #12
JSeery
Member Emeritus
 
JSeery's Avatar
 
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
Default Re: Complete Wiring for '51 Mercury

Don't know that it matters in your decision, but the cloth cover wires are modern wiring (similar to any wiring kit) with the cloth covering woven over them. Any other kit is most likely going to be the universal type and the color coding is not going to match (I believe most use the Chevy color coding). They will also most likely be built around a modern fuse panel. Nothing wrong with any of this, just something to be aware of.
JSeery is offline   Reply With Quote
Old 07-03-2019, 12:25 PM   #13
51 MERC-CT
Senior Member
 
51 MERC-CT's Avatar
 
Join Date: May 2010
Location: East Hartford, Ct
Posts: 5,898
Default Re: Complete Wiring for '51 Mercury

Quote:
Originally Posted by WABOOM View Post
Can anyone recommend a 6 volt kit replacement wiring kit that is good quality? not the expensive fabric wire reproduction?
Did see one that someone bought years ago from J C Whitney to fit a '50 Mercury that was plastic coated wire with no cloth cover.
Don't know if they still sell them.
Other than that, start collecting components to make your own.
__________________
DON'T RECALL DOING SOMETHING FOR MYSELF BASED ON SOMEONE ELSE'S LIKES OR DISLIKES
51 MERC-CT is offline   Reply With Quote
Old 07-03-2019, 02:20 PM   #14
51504bat
Senior Member
 
51504bat's Avatar
 
Join Date: Sep 2013
Location: SoCal-Redlands
Posts: 2,997
Default Re: Complete Wiring for '51 Mercury

Quote:
Originally Posted by WABOOM View Post
Can anyone recommend a 6 volt kit replacement wiring kit that is good quality? not the expensive fabric wire reproduction?
Try Sacramento Vintage Ford. Never used them but heard good things about their wiring stuff.
https://www.vintageford.com/sect_main.cfm?Line=main
__________________
Making the simple complicated for over 30 years.
51504bat is offline   Reply With Quote
Old 07-03-2019, 02:45 PM   #15
WABOOM
Senior Member
 
WABOOM's Avatar
 
Join Date: Jun 2018
Location: Minnesota
Posts: 347
Default Re: Complete Wiring for '51 Mercury

Quote:
Originally Posted by 51504bat View Post
Try Sacramento Vintage Ford. Never used them but heard good things about their wiring stuff.
https://www.vintageford.com/sect_main.cfm?Line=main
Oh man. Thank you. That's awesome.
WABOOM is offline   Reply With Quote
Old 07-03-2019, 03:13 PM   #16
TJ
Senior Member
 
TJ's Avatar
 
Join Date: May 2010
Location: Napa,California
Posts: 6,005
Default Re: Complete Wiring for '51 Mercury

I've used the Sacramento Vintage Ford harnesses and they work well. They are less expensive than others. I have no idea if they make them for the later Mercs.
TJ is offline   Reply With Quote
Old 07-04-2019, 07:11 AM   #17
38coop
Senior Member
 
Join Date: May 2010
Location: Cocoa Florida
Posts: 180
Default Re: Complete Wiring for '51 Mercury

Check with Tyree Harris. 804-556-5200. He makes a nice quality harness.
38coop is offline   Reply With Quote
Old 02-05-2020, 04:12 PM   #18
56markII
Member
 
56markII's Avatar
 
Join Date: Nov 2016
Location: Sask. Canada
Posts: 64
Default Re: Complete Wiring for '51 Mercury

Is Narragansette Reproductions still in business after Ed Pease passed away? Rhode Island Wire Works I have been told is better even though it's owned by Ed Pease's brother but Narragansette Reproductions makes wiring harnesses for my 56 Continental Mark II.
And yes I also have a 1950 Mercury Sport Sedan that will eventually get a wiring harness replacement perhaps from Rhode Island.
56markII is offline   Reply With Quote
Old 02-05-2020, 04:23 PM   #19
JSeery
Member Emeritus
 
JSeery's Avatar
 
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
Default Re: Complete Wiring for '51 Mercury

Deleted, I was off a page, LOL in the thread!!!

Last edited by JSeery; 02-05-2020 at 04:31 PM.
JSeery is offline   Reply With Quote
Old 02-05-2020, 09:48 PM   #20
richard crow
Senior Member
 
Join Date: May 2010
Posts: 1,763
Default Re: Complete Wiring for '51 Mercury

at those prices i would make my own remove your harness & copy them. you can buy the proper gauge wire at most parts stores . buy the correct termals on the inter net get a roll of thin soder & a sodering gun.take your time you can do it today with phone camars take pictures for routing .
richard crow is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 07:59 AM.