Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 02-16-2020, 10:08 AM   #1
sphooch
Senior Member
 
sphooch's Avatar
 
Join Date: Jan 2012
Location: New Jersey
Posts: 356
Default A big job ahead

I was just on this site with my Pitnam arm fix and now I have a new problem while working on the pitman arm I saw the drag link was rubbing on the tie rod. looking at the Les Andrews books I did the required measurements and as such determined the front spring should be replaced.i found on this site A-Spring made in the U.S.A. was the best. is this a big job, can some tell me if the Les Andrews replacement instructions are enough or are there some other things I should be aware of. thanks again THE HOOCH
sphooch is offline   Reply With Quote
Old 02-16-2020, 10:31 AM   #2
whirnot
Senior Member
 
whirnot's Avatar
 
Join Date: Mar 2013
Location: Bend Or.
Posts: 1,053
Default Re: A big job ahead

It's not too bad, but you need to find a spring spreader you can borrow.
__________________
Bill Worden

1929 Roadster
1929 Briggs Town Sedan
1930 Closed Cab pickup
Smith Motor Compressor
1951 Ford F1

High Desert Model A's
whirnot is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 02-16-2020, 10:39 AM   #3
Bob Bidonde
Senior Member
 
Bob Bidonde's Avatar
 
Join Date: May 2010
Location: Long Island, NY
Posts: 3,432
Default Re: A big job ahead

Ditto Whirnot! With a spring spreader, replacement of the front spring is relatively simple.
__________________
Bob Bidonde
Bob Bidonde is offline   Reply With Quote
Old 02-16-2020, 11:33 AM   #4
AL in NY
Senior Member
 
AL in NY's Avatar
 
Join Date: May 2010
Location: Southern Upstate New York
Posts: 1,149
Default Re: A big job ahead

I did both front and rear springs last year. You don't need a spring spreader to remove and replace the front spring. You just need a medium sized C-clamp to assemble the leaves of the front spring. Follow Les Andrews instructions and you'll have no problems. Easy one man job.
__________________
AL in NY
AL in NY is offline   Reply With Quote
Old 02-16-2020, 11:36 AM   #5
1931 flamingo
Senior Member
 
1931 flamingo's Avatar
 
Join Date: May 2010
Location: new britain,ct 06052
Posts: 9,389
Default Re: A big job ahead

Like Al says.
Paul in CT The rear spring is a different story.
1931 flamingo is offline   Reply With Quote
Old 02-16-2020, 11:38 AM   #6
WTSHNN
Senior Member
 
WTSHNN's Avatar
 
Join Date: May 2010
Location: Chicago
Posts: 1,413
Default Re: A big job ahead

Sponsored Links (Register now to hide all advertisements)
Agree that Travis at A Springs is the best option.

While you can do without a spring spreader I feel its safer and easier to use one. If you dont have one check with your local MARC region and see if someone has one you can borrow.

-Tim
__________________
No one wants advice - only corroboration.
-John Steinbeck
WTSHNN is offline   Reply With Quote
Old 02-16-2020, 11:47 AM   #7
AL in NY
Senior Member
 
AL in NY's Avatar
 
Join Date: May 2010
Location: Southern Upstate New York
Posts: 1,149
Default Re: A big job ahead

WTSHNN: The front spring is not under much tension, a spring spreader is NOT needed.
__________________
AL in NY
AL in NY is offline   Reply With Quote
Old 02-16-2020, 02:16 PM   #8
sphooch
Senior Member
 
sphooch's Avatar
 
Join Date: Jan 2012
Location: New Jersey
Posts: 356
Default Re: A big job ahead

thanks for the info. I do have a spring spreader and I also have a varity of c - clamps, both large and small. So I'll just follow Les Andrews . Now I just have to order the spring and get going on it. Thanks for the help once again. THE HOOCH
sphooch is offline   Reply With Quote
Old 02-16-2020, 02:28 PM   #9
Y-Blockhead
Senior Member
 
Y-Blockhead's Avatar
 
Join Date: Jul 2011
Location: Redondo Beach, CA
Posts: 5,817
Default Re: A big job ahead

Quote:
Originally Posted by sphooch View Post
I was just on this site with my Pitnam arm fix and now I have a new problem while working on the pitman arm I saw the drag link was rubbing on the tie rod. looking at the Les Andrews books I did the required measurements and as such determined the front spring should be replaced.i found on this site A-Spring made in the U.S.A. was the best. is this a big job, can some tell me if the Les Andrews replacement instructions are enough or are there some other things I should be aware of. thanks again THE HOOCH
I just replaced the front spring on my Town Sedan.

I got the spring from "A" Springs (http://www.a-springs.com/products.html), bushing pre-installed. I replaced the shackles and bushings in the spring perches at the same time. It took me less than an afternoon to install (after paint was dry), working by myself. I have a spring spreader but some use 2X4s.
Y-Blockhead is offline   Reply With Quote
Old 02-16-2020, 07:42 PM   #10
Sunnybrook Farm
Senior Member
 
Sunnybrook Farm's Avatar
 
Join Date: Oct 2015
Location: Virginia
Posts: 409
Default Re: A big job ahead

As I remember when I knocked the shackle out of my front spring, nothing happened other than the spring dropped down on the axle. Of course the front end was not under the car. Never took one loose while under the car!
Sunnybrook Farm is offline   Reply With Quote
Old 02-16-2020, 11:09 PM   #11
CWPASADENA
Senior Member
 
CWPASADENA's Avatar
 
Join Date: May 2010
Location: PASADENA, CA
Posts: 1,882
Default Re: A big job ahead

Support the front of the car with jacks stands under the frame.


With a floor jack under the center of the front axle, jack up the axle just a little to take the pressure off the shackles. Remove the shackle on one end of the spring. Remove the U bolt bottom plate and lower the front axle just a little so the spring is free from the cross member. Remove the other shackle and remove the spring.


Watch and do not bend down on the front brake rods, you may want to un-attach them at the front clevis.


Reverse the above instructions to replace the spring. You may have to place a thin block of wood on top of the axle under the eye of the spring to help with alignment when installing the last shackle.


I have used this method for a very long time with very good success. It is fast, easy and most important safe as you do not have a spring spreader.


Chris W.
CWPASADENA is offline   Reply With Quote
Old 02-16-2020, 11:24 PM   #12
holdover
Senior Member
 
Join Date: May 2011
Location: SW Virginia near the Blue ridge Parkway
Posts: 674
Default Re: A big job ahead

Front spring not a problem, do as # 11 says, the rear spring is a different animal where you need to be careful Good luck.
holdover is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 08:44 AM.