|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
02-22-2018, 03:06 PM | #1 |
Member
Join Date: May 2010
Location: Michigan
Posts: 87
|
60 hp waterpump fitment
I can't get the waterpump to seat against the outer gasket. I rebuilt the pump and replaced the rubber inner seal. I don't know why this won't tighten up.
See attached photo. Image I have cleaned the housing and even have tried a nos pump with the same result. Any suggestions would be appreciated. This is the straight pumps from a 38 ford. Last edited by fordor; 02-22-2018 at 03:13 PM. Reason: Add a photo |
02-22-2018, 03:37 PM | #2 |
Member
Join Date: May 2010
Location: Michigan
Posts: 87
|
Re: 60 hp waterpump fitment
Can't seem to load pic.
|
Sponsored Links (Register now to hide all advertisements) |
|
02-22-2018, 05:42 PM | #3 |
Senior Member
Join Date: Nov 2012
Location: Elgin Illinois
Posts: 736
|
Re: 60 hp waterpump fitment
Do you think you might have mixed matched the tapered housing to the straight pumps?
|
02-22-2018, 06:47 PM | #4 |
Member
Join Date: May 2010
Location: Michigan
Posts: 87
|
Re: 60 hp waterpump fitment
No, I have the right housing. I have a 37 housing also(tapered). I can tell the difference.
|
02-22-2018, 08:39 PM | #5 |
Senior Member
Join Date: Aug 2010
Location: East Boothbay, Maine
Posts: 279
|
Re: 60 hp waterpump fitment
Those tapered housings tend to corrode in the seal area and sometimes with deep pitting. I sand blasted mine and filled the pits with JB Weld. Smoothed everything up and got a good seal.
|
02-22-2018, 09:37 PM | #6 |
Member Emeritus
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
|
Re: 60 hp waterpump fitment
|
02-23-2018, 09:41 AM | #7 |
Member
Join Date: May 2010
Location: Michigan
Posts: 87
|
Re: 60 hp waterpump fitment
If you would. I'll be ail it to you.
Thanks |
02-23-2018, 09:46 AM | #8 |
Member
Join Date: May 2010
Location: Michigan
Posts: 87
|
Re: 60 hp waterpump fitment
So how do I email it to you? I don't see where I can send an attachment or pic from my photos.
|
02-23-2018, 05:44 PM | #9 |
Member Emeritus
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
|
Re: 60 hp waterpump fitment
fordor wanted me to post a photo for him. Not sure which way you wanted it turned.
Last edited by JSeery; 02-23-2018 at 05:49 PM. |
02-23-2018, 09:47 PM | #10 |
Senior Member
Join Date: Nov 2012
Location: Elgin Illinois
Posts: 736
|
Re: 60 hp waterpump fitment
Are you using a flathead 60 waterpump tool to tighten it ?
|
02-23-2018, 09:52 PM | #11 |
Member
Join Date: May 2010
Location: Michigan
Posts: 87
|
Re: 60 hp waterpump fitment
Yes I have the proper spanner wrench. Still end up with the same gap.
|
02-24-2018, 05:58 PM | #12 |
Senior Member
Join Date: May 2010
Location: San Jose, CA
Posts: 287
|
Re: 60 hp waterpump fitment
I had a similar situation 22 years ago on my 37 Tudor 60 hp. I could not get the water pump to seat down tight against the housing. I put (2) of the copper washers between the pump and the housing, tightened it down and 22 years later, still no leaks.
|
02-24-2018, 07:05 PM | #13 |
Member
Join Date: May 2010
Location: Michigan
Posts: 87
|
Re: 60 hp waterpump fitment
Yea, I guess I'm going to have to double up the gasket and see what happens.
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|