hub face to hub face on 46 ford

[HOTRODRON]

what is the measurement from hub to hub on a 1946 ford rear end

[rich b]

My list says 61"

[GB SISSON]

car, truck, tonner? I could check the trucks tomorrow...

[V8COOPMAN]

Originally Posted by rich b

My list says 61"

Mine says the same! DD


1928-1931 57.0″ Spring Mount Eye to Eye 49.5″

1932-1934 57.75″ --------------------------- 47.5″

1935-1936 59.5″ ----------------------------48.25″

1937-1940 59.5″ -----------------------------48.5″


1941 59.5"-------------------------------------46.75"

1942-1948 61.0″ -----------------------------46.75"

[qmdv]

Originally Posted by HOTRODRON

what is the measurement from hub to hub on a 1946 ford rear end

Hey you should drive up to Yreka, CA and I will give you a 46 rear end, rear spring, front axle and front wish bone. Free I am moving and cannot bear to scrap it

[cas3]

Sponsored Links (Register now to hide all advertisements)

a bargain at twice the price!

[GB SISSON]

Is spring eye to spring eye the same as hub face to hub face? I don't see that....

[cas3]

jeez louise, gotta teach these green horns everything! hub face, as in axle flange face where the drum & wheel mount, no springs involved. there was a thread recently with an old magazine article with all the banjo axle widths, sorry gary, its late, and i'm too lazy to look it up for you, but you get the idea. hows the busted hand doing? hows the diesel doing?

[V8COOPMAN]

Originally Posted by GB SISSON

Is spring eye to spring eye the same as hub face to hub face? I don't see that....

Look carefully at the RIGHT hand column in post #4......SPRING EYE measurements! DD

[GB SISSON]

Originally Posted by cas3

jeez louise, gotta teach these green horns everything! hub face, as in axle flange face where the drum & wheel mount, no springs involved. there was a thread recently with an old magazine article with all the banjo axle widths, sorry gary, its late, and i'm too lazy to look it up for you, but you get the idea. hows the busted hand doing? hows the diesel doing?

My mistake! I read coopman's list wrong. The spring eye dimension was on the far right and hub face was on the left. Now I see it. I have swapped out a lot of axles, including spending last weekend swapping the complete rear axle in my 92 f350 cab and chassis dually with one from a wrecking yard. You can't believe how few guys on the phone knew anything about axle widths between the dually cc and the super wide dually pickup, or the srw and drw versions. Sheesh. Hands are healed, diesel is awful loud in the cab, And Coopman, I apologize for doubting the info on your list.

[JSeery]

Originally Posted by cas3

jeez louise, gotta teach these green horns everything! hub face, as in axle flange face where the drum & wheel mount, no springs involved. there was a thread recently with an old magazine article with all the banjo axle widths, sorry gary, its late, and i'm too lazy to look it up for you, but you get the idea. hows the busted hand doing? hows the diesel doing?

Question has already been answered, so this is a bit late, but believe these may be pages you were referring to. (not easy to read).

[JSeery]

Not sure why, but the StreetRodder article measurements are slightly different from the ones V8Coopman posted. Would guess it has to do with how you take the measurements. Here are the SR numbers if you can't read the chart in the scan.

The numbers are year(s)/Backing Plate Width/Outside Width/Spring Hanger Width

35-36 / 51.25 / 59.25 / 48.50
37-40 / 51.25 / 59.25 / 48.50
41 / 51.25 / 59.25 / 46.75
42-48 / 53.00 /61.00 / 46.75

[ford38v8]

Here's the Street Rodder article, full size. For future reference, it's posted on my V8 Club RG's website.


http://goldengatev8.org/images/Stree..._magazine.html