Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 03-23-2018, 09:16 AM   #1
Garagekulture13
Senior Member
 
Garagekulture13's Avatar
 
Join Date: Nov 2015
Location: Middle Tennessee
Posts: 179
Default Chasing the knock.

I just purchased my 2nd Model A title says 1932 but it's a 1931 to me. Any way, it has a knock. It has been sitting in an 80 year old man's house for sometime. I had a previous problem of it not running well after a carb rebuild but it was solved with another carb. The car starts good, runs good, and drives out good but does have a knock. So I started investigating. I am a novice so if you see something in the pics by all means tell me. All the lifters are free. I do see a couple new valves. Pulled the cover to inspect the timing gear and is worn pretty badly. I have a new one on the way. I just tried to drain the oil and when I pulled the plug nothing came out. I had to stick a screwdriver in the hole to get the oil to come out. I then dropped the pan. Other than about a half inch of sludge I didn't find anything in the pan. Video is just for noise reference and was taken when I was trying to figure out the carb problem.

https://youtu.be/3R3eLKlvVmU

https://youtu.be/X1Jxiqp16Xw

Sent from my SM-N950U using Tapatalk
Garagekulture13 is offline   Reply With Quote
Old 03-23-2018, 09:28 AM   #2
Brendan
Senior Member
 
Brendan's Avatar
 
Join Date: May 2010
Location: At my kitchen table in Santa Rosa, Ca
Posts: 2,902
Default Re: Chasing the knock.

you do have a dipper tray in your pan don't you?
__________________
If it would have been a snake it would have bit ya!

i can't spell my way out of a paper bag!
Brendan is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 03-23-2018, 09:33 AM   #3
Garagekulture13
Senior Member
 
Garagekulture13's Avatar
 
Join Date: Nov 2015
Location: Middle Tennessee
Posts: 179
Default Re: Chasing the knock.

Quote:
Originally Posted by Brendan View Post
you do have a dipper tray in your pan don't you?
The tray in the pan? Yes. I removed it to get to the sludge and get the pan cleaned.

Sent from my SM-N950U using Tapatalk
Garagekulture13 is offline   Reply With Quote
Old 03-23-2018, 09:42 AM   #4
jwilliams81
Senior Member
 
jwilliams81's Avatar
 
Join Date: Sep 2016
Location: Cincinnati OH
Posts: 418
Default Re: Chasing the knock.

Backfiring could be a stuck valve. That's what mine was.
https://photos.app.goo.gl/iClD1SDIi2GlozyZ2

Fixed it:
https://photos.app.goo.gl/DfOHWJclaOtRwhMv2
__________________
1931 Murray Town Sedan. Black body with Apple Green pin stripe.
1923 Model T Touring with electric start. Low radiator
Cincinnati, Ohio
jwilliams81 is offline   Reply With Quote
Old 03-23-2018, 09:42 AM   #5
katy
Senior Member
 
katy's Avatar
 
Join Date: Jun 2015
Location: Red Deer, Alberta
Posts: 5,004
Default Re: Chasing the knock.

Quote:
Any way, it has a knock. It has been sitting in an 80 year old man's house for sometime. I had a previous problem of it not running well after a carb rebuild but it was solved with another carb. The car starts good, runs good, and drives out good but does have a knock. So I started investigating. I am a novice so if you see something in the pics by all means tell me. All the lifters are free. I do see a couple new valves. Pulled the cover to inspect the timing gear and is worn pretty badly. I have a new one on the way. I just tried to drain the oil and when I pulled the plug nothing came out. I had to stick a screwdriver in the hole to get the oil to come out. I then dropped the pan. Other than about a half inch of sludge I didn't find anything in the pan.
Did you not check the oil level on the dipstick when you bought it?
__________________
If you don't hear a rumor by 10 AM, start one!.
Got my education out behind the barn!
katy is offline   Reply With Quote
Old 03-23-2018, 09:45 AM   #6
Garagekulture13
Senior Member
 
Garagekulture13's Avatar
 
Join Date: Nov 2015
Location: Middle Tennessee
Posts: 179
Default Re: Chasing the knock.

Sponsored Links (Register now to hide all advertisements)
Quote:
Originally Posted by jwilliams81 View Post
Backfiring could be a stuck valve.
From what I could see all the valves are moving freely. After the new carb and new plug contactor it no longer back fired.

Sent from my SM-N950U using Tapatalk
Garagekulture13 is offline   Reply With Quote
Old 03-23-2018, 09:46 AM   #7
Garagekulture13
Senior Member
 
Garagekulture13's Avatar
 
Join Date: Nov 2015
Location: Middle Tennessee
Posts: 179
Default Re: Chasing the knock.

Quote:
Originally Posted by katy View Post
Did you not check the oil level on the dipstick when you bought it?
I did and it was spot on level with no sludge on the dipstick.

Sent from my SM-N950U using Tapatalk
Garagekulture13 is offline   Reply With Quote
Old 03-23-2018, 10:20 AM   #8
Patrick L.
Senior Member
 
Patrick L.'s Avatar
 
Join Date: May 2010
Location: Largo Florida
Posts: 7,225
Default Re: Chasing the knock.

Can you tell about where the knock seems to be coming from ?

Have you checked the lash of the timing gears ? Anything more than about .009" and they'll rattle. Yours don't look very good from the picture, but, checking the lash is whats needed.

Running the engine with the timing pin inserted and putting pressure on the gear is sometimes a good way to determine if the gear is bad/worn.
Patrick L. is offline   Reply With Quote
Old 03-23-2018, 10:23 AM   #9
Bill Pursel
Member
 
Bill Pursel's Avatar
 
Join Date: Nov 2017
Location: Terre Haute, Indiana
Posts: 90
Default Re: Chasing the knock.

That thing needs a bath....before you clean valve chamber block crank and cam oil passages with wood dowels so you dont get debris in them
Bill Pursel is offline   Reply With Quote
Old 03-23-2018, 10:31 AM   #10
Garagekulture13
Senior Member
 
Garagekulture13's Avatar
 
Join Date: Nov 2015
Location: Middle Tennessee
Posts: 179
Default Re: Chasing the knock.

Quote:
Originally Posted by Patrick L. View Post
Can you tell about where the knock seems to be coming from ?

Have you checked the lash of the timing gears ? Anything more than about .009" and they'll rattle. Yours don't look very good from the picture, but, checking the lash is whats needed.

Running the engine with the timing pin inserted and putting pressure on the gear is sometimes a good way to determine if the gear is bad/worn.
I ran with the side cover off and it sounded to me to be coming from the front of the engine. That's what led me to pull the timing gear cover. I will check the lash.

Sent from my SM-N950U using Tapatalk
Garagekulture13 is offline   Reply With Quote
Old 03-23-2018, 10:33 AM   #11
Bulligen
Senior Member
 
Bulligen's Avatar
 
Join Date: Nov 2012
Location: Elgin Illinois
Posts: 735
Default Re: Chasing the knock.

That fiber gear can have a bad sounding knock when it is worn!!
Bulligen is offline   Reply With Quote
Old 03-23-2018, 10:38 AM   #12
Wick
Senior Member
 
Wick's Avatar
 
Join Date: May 2010
Location: Gwynn's Island Va
Posts: 1,380
Default Re: Chasing the knock.

I've had a couple of motors that looked like this. By the amount of dirt and sludge and the timing gear I'd say the oil wasn't changed often. Look at the scoring on # 2 and 3 cylinders. The Pistons are probley slapping.
Wick is offline   Reply With Quote
Old 03-23-2018, 10:54 AM   #13
Jim Brierley
Senior Member
 
Join Date: Jun 2010
Location: Temecula, CA
Posts: 4,066
Default Re: Chasing the knock.

Your car was likely built in 1932, but is of all 1931 parts. A friend of mine has a wide-bed pickup registered like that. Good luck with finding and fixing you noise.
Jim Brierley is offline   Reply With Quote
Old 03-23-2018, 11:11 AM   #14
George Miller
Senior Member
 
George Miller's Avatar
 
Join Date: May 2010
Location: NC
Posts: 2,975
Default Re: Chasing the knock.

It is really hard to tell by the picture, but it looks like your timing gear teeth are worn real bad.
To find the noise it is best to short out each cylinder one at a time. Do this before you tear it down. This way you can tell if it is a rod, main, or piston. It also tells you which cylinder or which main is knocking. It would not tell you if it is a timing gear.
George Miller is offline   Reply With Quote
Old 03-23-2018, 11:14 AM   #15
Garagekulture13
Senior Member
 
Garagekulture13's Avatar
 
Join Date: Nov 2015
Location: Middle Tennessee
Posts: 179
Default Re: Chasing the knock.

Quote:
Originally Posted by George Miller View Post
It is really hard to tell by the picture, but it looks like your timing gear teeth are worn real bad.
To find the noise it is best to short out each cylinder one at a time. Do this before you tear it down. This way you can tell if it is a rod, main, or piston. It also tells you which cylinder or which main is knocking. It would not tell you if it is a timing gear.
I did this but not really any change in the knock.

Sent from my SM-N950U using Tapatalk
Garagekulture13 is offline   Reply With Quote
Old 03-23-2018, 11:27 AM   #16
PC/SR
Senior Member
 
Join Date: May 2010
Location: Santa Rosa, CA
Posts: 1,276
Default Re: Chasing the knock.

Since the pan is off, you should check the rod and main bearing clearances with plastigage, and check the babbitt condition of the caps. There are lots of threads on this in the search function. I also put 4x4 block of wood under the front wheels--the extra room makes things easier.
PC/SR is offline   Reply With Quote
Old 03-23-2018, 11:52 AM   #17
1955cj5
Senior Member
 
1955cj5's Avatar
 
Join Date: Apr 2015
Location: Boise, Idaho
Posts: 1,576
Default Re: Chasing the knock.

Just for comparison, here is a laminated fiber gear with about 1500 miles on it.
Attached Images
File Type: jpg P1020347.JPG (163.3 KB, 193 views)
__________________
Early '29 CCPU that had a 4-speed, but not any more.......in the family since '62
1955cj5 is offline   Reply With Quote
Old 03-23-2018, 12:18 PM   #18
Garagekulture13
Senior Member
 
Garagekulture13's Avatar
 
Join Date: Nov 2015
Location: Middle Tennessee
Posts: 179
Default Re: Chasing the knock.

Quote:
Originally Posted by 1955cj5 View Post
Just for comparison, here is a laminated fiber gear with about 1500 miles on it.
Good gosh mine is wore out!

Sent from my SM-N950U using Tapatalk
Garagekulture13 is offline   Reply With Quote
Old 03-23-2018, 12:19 PM   #19
Garagekulture13
Senior Member
 
Garagekulture13's Avatar
 
Join Date: Nov 2015
Location: Middle Tennessee
Posts: 179
Default Re: Chasing the knock.

I did just notice both motor mount bolts are loose and I have not touched either.

Sent from my SM-N950U using Tapatalk

Last edited by Garagekulture13; 03-23-2018 at 12:31 PM.
Garagekulture13 is offline   Reply With Quote
Old 03-23-2018, 03:49 PM   #20
Farrell In Vancouver
Senior Member
 
Farrell In Vancouver's Avatar
 
Join Date: May 2010
Location: Pitt Meadows BC
Posts: 1,003
Default Re: Chasing the knock.

Might be a good time to yank that engine and go through it carefully. The dirt and sludge can't be doing anything but hurting. The car is nice enough to deserve a pretty, quiet engine, and give you a ton of piece of mind while you enjoy it.
Farrell In Vancouver is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 04:34 AM.