Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 04-20-2019, 03:59 PM   #1
WillC
Member
 
Join Date: Mar 2011
Posts: 44
Default Venturi Extraction tool

Would anyone have a venturi extraction tool for a Zenith carburetor I could buy/ barrow?
WillC is offline   Reply With Quote
Old 04-21-2019, 06:45 AM   #2
MickeyT
Senior Member
 
MickeyT's Avatar
 
Join Date: Jul 2017
Location: Texas
Posts: 179
Send a message via AIM to MickeyT Send a message via MSN to MickeyT Send a message via Yahoo to MickeyT
Default Re: Venturi Extraction tool

Try this.

https://www.brattons.com/carburetor-venturi-puller.html
MickeyT is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 04-21-2019, 02:48 PM   #3
califfarmer
Member
 
califfarmer's Avatar
 
Join Date: May 2014
Location: Newbury Park, CA
Posts: 41
Default Re: Venturi Extraction tool

Be careful! According to the Bratton’s website that tool might cause cancer. It has a prop65 warning.
__________________
Eat more large Lima beans!!
califfarmer is offline   Reply With Quote
Old 04-21-2019, 06:09 PM   #4
WillC
Member
 
Join Date: Mar 2011
Posts: 44
Default Re: Venturi Extraction tool

Thanks guys, I was able to make one and it worked great. If anybody's interested here's what I did. One small piece of galvanized pipe about 4 inches long and it big enough to fit over the ventri. A foot long piece of 1/2 all thread and 4 1/2 nuts. Four 1'2 inch nuts and washers. I put the washers on the all thread and about 2 inches down I secured the washers together with two nuts and put them in my drill press and as the drill press was turning I used m files to turn down the size of the nuts to fit inside the carburetor body. Be careful so you don't turn them down to much. When the washers were the right size I placed them in the carburetor and doubled nutted two nuts on the all thread. I put the all thread up threw the carburetor and place the pipe on the top and used the last nut top put out the ventri. I wish I was able to put a photo on here but I don't know how.
WillC is offline   Reply With Quote
Old 04-22-2019, 06:31 PM   #5
Don Turley
Senior Member
 
Don Turley's Avatar
 
Join Date: May 2010
Location: GA 30809
Posts: 591
Default Re: Venturi Extraction tool

Here are photos of one I made many years ago.
Piece of pipe slightly larger than the venturi diameter. Top plate has a hole for clearance of the bolt. Machined puller plate is threaded to fit the bolt.
Attached Images
File Type: jpg Carburetor venturi tool 001.jpg (24.2 KB, 18 views)
File Type: jpg Carburetor venturi tool 005.jpg (34.5 KB, 11 views)
Don Turley is offline   Reply With Quote
Old 04-22-2019, 11:09 PM   #6
29leatherbackA
Junior Member
 
Join Date: Aug 2018
Location: Wisconsin
Posts: 13
Default Re: Venturi Extraction tool

Sponsored Links (Register now to hide all advertisements)
I just used a socket and some tapping on the bench to remove mine.
29leatherbackA is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 08:20 AM.