Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 02-25-2019, 11:45 AM   #1
Rustbelt A
Junior Member
 
Rustbelt A's Avatar
 
Join Date: Apr 2017
Location: Toronto GTA
Posts: 19
Default Rivets or weld?

Is there any reason a sub frame should be riveted, other than for originality?

I’m putting a new one together and would think welding is easier and stronger...with that said, I’ve learned a lot of things are a specific way for a reason.

Anyone else just weld it up an go?
Rustbelt A is offline   Reply With Quote
Old 02-25-2019, 12:05 PM   #2
Purdy Swoft
Senior Member
 
Purdy Swoft's Avatar
 
Join Date: May 2010
Location: Alabama
Posts: 8,099
Default Re: Rivets or weld?

Welding body parts together instead of riveting Takes away flexability that is needed . usually the experts will point out that the parts should have been riveted and you will have to listen and wish that you had used rivets instead .
Purdy Swoft is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 02-25-2019, 12:16 PM   #3
Tacoma Bob
Senior Member
 
Tacoma Bob's Avatar
 
Join Date: May 2010
Location: Tacoma, WA
Posts: 1,025
Default Re: Rivets or weld?

Built many a hot rod Model "A" and other vintage street rod and race cars. When it comes to frames................weld away.
Tacoma Bob is offline   Reply With Quote
Old 02-25-2019, 12:58 PM   #4
Pete
Senior Member
 
Pete's Avatar
 
Join Date: May 2010
Location: Wa.
Posts: 5,374
Default Re: Rivets or weld?

The more rigid the better. Weld is good.
Pete is offline   Reply With Quote
Old 02-25-2019, 05:06 PM   #5
Synchro909
Senior Member
 
Synchro909's Avatar
 
Join Date: Jun 2014
Location: Melbourne, Australia
Posts: 7,472
Default Re: Rivets or weld?

Quote:
Originally Posted by Tacoma Bob View Post
Built many a hot rod Model "A" and other vintage street rod and race cars. When it comes to frames................weld away.
Weld away, OK but is there a particular electrode you'd use? Not that I would weld anyway - the law says NO and I don't want to be on the wrong end of a law suit.
__________________
I'm part of the only ever generation with an analogue childhood and a digital adulthood.
Synchro909 is offline   Reply With Quote
Old 02-25-2019, 05:39 PM   #6
Oldbluoval
Senior Member
 
Oldbluoval's Avatar
 
Join Date: Jun 2015
Location: Signal Mtn, TN (SE TN)
Posts: 2,360
Default Re: Rivets or weld?

Sponsored Links (Register now to hide all advertisements)
Do you intend to mig or
Tig?
I'd rivet
Oldbluoval is offline   Reply With Quote
Old 02-25-2019, 07:45 PM   #7
Pete
Senior Member
 
Pete's Avatar
 
Join Date: May 2010
Location: Wa.
Posts: 5,374
Default Re: Rivets or weld?

Quote:
Originally Posted by Synchro909 View Post
Weld away, OK but is there a particular electrode you'd use? Not that I would weld anyway - the law says NO and I don't want to be on the wrong end of a law suit.
6011 for arc welding.
ER 70 for TIG.

I would not mig weld anything
Pete is offline   Reply With Quote
Old 02-25-2019, 07:47 PM   #8
whirnot
Senior Member
 
whirnot's Avatar
 
Join Date: Mar 2013
Location: Bend Or.
Posts: 1,053
Default Re: Rivets or weld?

Quote:
Originally Posted by Pete View Post
6011 for arc welding.
ER 70 for TIG.

I would not mig weld anything
Why?
__________________
Bill Worden

1929 Roadster
1929 Briggs Town Sedan
1930 Closed Cab pickup
Smith Motor Compressor
1951 Ford F1

High Desert Model A's
whirnot is offline   Reply With Quote
Old 02-25-2019, 09:27 PM   #9
1ton
Senior Member
 
Join Date: Jun 2012
Location: North Aurora,Il.
Posts: 154
Default Re: Rivets or weld?

"Why" is a great question. I don't know about the early frames but as the years rolled on , the carbon content of car/truck frames went up to make them stronger. Unless you are planning to draw the weld back with a torch, mig would be a poor choice. Would stick welding it with a low carbon rod like 1018 be a better choice than 6011? I'd like to know.
1ton is offline   Reply With Quote
Old 02-26-2019, 03:50 AM   #10
McCready
Junior Member
 
McCready's Avatar
 
Join Date: Sep 2011
Location: High camp
Posts: 29
Send a message via MSN to McCready
Default Re: Rivets or weld?

Yeah weld away bet u can't do this one with your mild steel crossmembers
Attached Images
File Type: jpeg image.jpeg (174.6 KB, 59 views)
McCready is offline   Reply With Quote
Old 02-26-2019, 04:02 AM   #11
Tom Wesenberg
Senior Member
 
Tom Wesenberg's Avatar
 
Join Date: May 2010
Location: Mpls, MN
Posts: 27,582
Default Re: Rivets or weld?

I would rivet the frame, just like original.
Tom Wesenberg is offline   Reply With Quote
Old 02-26-2019, 06:34 AM   #12
BRENT in 10-uh-C
Senior Member
 
BRENT in 10-uh-C's Avatar
 
Join Date: May 2010
Location: Eastern Tennessee
Posts: 11,486
Default Re: Rivets or weld?

Hey guys, please reread the question as this is likely confusing the original poster (-and anyone in the future looking at this post for advice). If I am understanding his question, he is about to assemble the floor sills of a body. He is NOT working on the frame of the vehicle.
__________________
.

BRENT in 10-uh-C
.
www.model-a-ford.com
...(...Finally Updated!! )

.
BRENT in 10-uh-C is offline   Reply With Quote
Old 02-26-2019, 02:46 PM   #13
Pete
Senior Member
 
Pete's Avatar
 
Join Date: May 2010
Location: Wa.
Posts: 5,374
Default Re: Rivets or weld?

I read "sub frame" but a lot of people don't know the difference.
I would still weld.
Pete is offline   Reply With Quote
Old 02-26-2019, 06:05 PM   #14
SSsssteamer
Senior Member
 
SSsssteamer's Avatar
 
Join Date: Nov 2010
Location: Sedro-Woolley, WA
Posts: 1,023
Default Re: Rivets or weld?

Quote:
Originally Posted by Pete View Post
I read "sub frame" but a lot of people don't know the difference.
I would still weld.
I riveted the subframe on my 1930 phaeton. It wasn't that hard to do and I will never regret that I riveted it instead of welded it.
SSsssteamer is offline   Reply With Quote
Old 02-26-2019, 11:16 PM   #15
Purdy Swoft
Senior Member
 
Purdy Swoft's Avatar
 
Join Date: May 2010
Location: Alabama
Posts: 8,099
Default Re: Rivets or weld?

Welding sub frames on hot rods wouldn't make that much difference in the value of the car . Original cars had the body parts riveted , so was the frame parts . Welding either of the parts together would just be a patch up job instead of a restoration . The car would lose points in national judging and would also lose value .
Purdy Swoft is offline   Reply With Quote
Old 02-26-2019, 11:27 PM   #16
Railcarmover
BANNED
 
Join Date: Apr 2017
Location: Sacramento
Posts: 1,262
Default Re: Rivets or weld?

6011 is junk rod,made for rough dirty work,initially designed for chain link fence work,perfect for original sub rail repair. New fabrication? MIG,both for speed and weld quality.
Ford pioneered 'electric welding' in automotive production,look no further than your rear axle housing for an example of automated jig welding.As welding technology improved the riveting of steel waned..that being said,authenticity suffers if your inclined that way.
Railcarmover is offline   Reply With Quote
Old 02-27-2019, 01:07 AM   #17
updraught
Senior Member
 
updraught's Avatar
 
Join Date: Feb 2015
Location: Australia
Posts: 1,967
Default Re: Rivets or weld?

"Since no provision is kept for expansion and contraction in the frame, therefore there is a possibility of cracks developing in it."

https://me-mechanicalengineering.com...iveted-joints/

The frame for an LPG tank on my modern-ish car was welded in. I've been told a number of times to have it taken out and bolted in because of the twisting of the chassis. The weld has already broken once. It requires regular checking.



PS. "The welding provides very strong joints. which can’t be bended easily."

Must be American English?
updraught is offline   Reply With Quote
Old 02-27-2019, 09:23 AM   #18
Railcarmover
BANNED
 
Join Date: Apr 2017
Location: Sacramento
Posts: 1,262
Default Re: Rivets or weld?

Welding gets a bad name due to the welder not practicing the "5P's"

proper planning prevents piss poor performance.


riveting or bolting will accommodate flexibility till the fastener fails,the same as welding.welded correctly on most applications you will achieve a greater grip surface than bolting or riveting, which only provides tension at the fastener.
Railcarmover is offline   Reply With Quote
Old 02-27-2019, 09:49 AM   #19
GRutter
Senior Member
 
GRutter's Avatar
 
Join Date: Sep 2017
Location: Mint Hill, North Carolina
Posts: 386
Default Re: Rivets or weld?

If you look at construction of buildings built during the 1930's, such as the Empire State Building, EVERYTHING is riveted. I'm sure there is a reason - strength, flexibility, worker capabilities, consistency of joint strength, no issues with changing the temper of the steel, speed of assembly. Similar considerations probably went into production of the A. Ford used a lot of welded assemblies.. but they were machine / jig welded. Where manual assembly was required, the parts are riveted.
GRutter is offline   Reply With Quote
Old 02-28-2019, 12:54 PM   #20
whirnot
Senior Member
 
whirnot's Avatar
 
Join Date: Mar 2013
Location: Bend Or.
Posts: 1,053
Default Re: Rivets or weld?

Quote:
Originally Posted by GRutter View Post
If you look at construction of buildings built during the 1930's, such as the Empire State Building, EVERYTHING is riveted. I'm sure there is a reason - strength, flexibility, worker capabilities, consistency of joint strength, no issues with changing the temper of the steel, speed of assembly. Similar considerations probably went into production of the A. Ford used a lot of welded assemblies.. but they were machine / jig welded. Where manual assembly was required, the parts are riveted.
Structures today are bolted instead if rvited. Better bolt s. They are not welded because if flexibility.
__________________
Bill Worden

1929 Roadster
1929 Briggs Town Sedan
1930 Closed Cab pickup
Smith Motor Compressor
1951 Ford F1

High Desert Model A's
whirnot is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 09:10 PM.