Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 03-01-2020, 11:39 AM   #1
johnbuckley
Senior Member
 
johnbuckley's Avatar
 
Join Date: Jul 2010
Location: United Kingdom
Posts: 1,439
Default Why a fibre thrust washer on distributor?

1) I can see the reason to have a thrust wsher to stop axial movement of the distributor shaft but isn't the fibre thrust washer (A12181) sold by the usual suppliers going to wear out within the first few thousand revs? Surely a steel shim washers would be better?
ALSO. 2) What is the logic for having a plain washer under the lock washer of the cam screw? (no part number for the plain washer but it's item #33 in the Brattons/snyders exploded diagram)
johnbuckley is online now   Reply With Quote
Old 03-01-2020, 12:52 PM   #2
Russ/40
Senior Member
 
Russ/40's Avatar
 
Join Date: May 2010
Location: Santee, California
Posts: 3,505
Default Re: Why a fibre thrust washer on distributor?

The fiber thrust washer on the bottom gets well lubricated, and the load on it is negligible. It is much like the fiber washers found in generators, that never seem to get any wear. The flat washer under the cam lock washer helps keep the point cam from moving when tightening the cam screw. At least that is my feelings on the matter. I have observed that the fiber washers at the bottom are always too thick. I use one like the kind found under the top plate, for the lower thrust as well because they are closer to the thickness needed. I adjust up/down thrust, if needed, by honing the top surface of the bottom collar enough to set thrust and allignment of the bottom pin. Works for me, although time consuming to get it right.

Last edited by Russ/40; 03-06-2020 at 05:29 PM.
Russ/40 is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 03-01-2020, 03:56 PM   #3
johnbuckley
Senior Member
 
johnbuckley's Avatar
 
Join Date: Jul 2010
Location: United Kingdom
Posts: 1,439
Default Re: Why a fibre thrust washer on distributor?

Thanks Russ, all makes sense now you've explained it!
johnbuckley is online now   Reply With Quote
Old 03-06-2020, 07:47 AM   #4
RonC
Senior Member
 
RonC's Avatar
 
Join Date: May 2010
Location: Rhode Island
Posts: 1,868
Default Re: Why a fibre thrust washer on distributor?

Ford specified .004-.010 end play. There should be a fiber washer A-22331 under the shaft collar to keep the oil out of the top housing not a steel washer. No washer goes on the bottom. The design is to allow the engine oil to travel up the shaft.
RonC is offline   Reply With Quote
Old 03-06-2020, 12:37 PM   #5
Benson
Senior Member
 
Join Date: May 2010
Posts: 2,579
Default Re: Why a fibre thrust washer on distributor?

JOHN,


WWW.MODELASTORE.COM (berts) has both fiber and steel washers


steel are .015


fiber are .030 thick


so you could use two steel in place of the fiber one for a total of three washers.


steel here:


https://modelastore.com/electrical/d...roduct_id=4221


Fiber here:


https://modelastore.com/electrical/d...roduct_id=4222
Benson is offline   Reply With Quote
Old 03-06-2020, 01:52 PM   #6
johnbuckley
Senior Member
 
johnbuckley's Avatar
 
Join Date: Jul 2010
Location: United Kingdom
Posts: 1,439
Default Re: Why a fibre thrust washer on distributor?

Sponsored Links (Register now to hide all advertisements)
Thanks all, I was intrigued by why a fibre washer wouldn't wear away quickly and why there a washer was used under the cam screw . Russ's explanaton #2 sounds logical .
johnbuckley is online now   Reply With Quote
Old 03-06-2020, 02:05 PM   #7
Tom Endy
Senior Member
 
Tom Endy's Avatar
 
Join Date: May 2010
Location: Southern California
Posts: 3,122
Default Re: Why a fibre thrust washer on distributor?

I am also in agreement with post #2. I believe that the .015 steel washer at the top is there as a thrust washer and helps prevent wear to the top of the casting tunnel. The fiber washer goes to the bottom. I am not sure the purpose, but most drawings show it there. When rebuilding a distributor I try to eliminate excessive thrust clearance. Sometimes I have to add a second .015 steel washer above the fiber washer at the bottom if there is excessive thrust. Other times I have had to grind material off the top of the collar at bottom to achieve proper thrust clearance with a steel washer at the top and a fiber washer at the bottom.

Tom Endy
Tom Endy is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 04:06 AM.