Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 08-17-2019, 02:16 PM   #1
alexiskai
Senior Member
 
alexiskai's Avatar
 
Join Date: Apr 2018
Location: Mebane NC
Posts: 2,330
Default Sanity check on lubing springs in place

I want to try to improve ride and correct a slight lean by lubricating the springs without removing them. I know the "right" way is to take the springs out and check them, but I don't want to spend the time/money.

Since I haven't done this before, I was hoping somebody could take a look at this planned sequence and tell me if I'm missing anything or creating problems. I'm planning to do the whole sequence once for the front springs and once for the rear.
  1. Detach shock arms and brake rods
  2. Jack up the frame maybe a foot
  3. Jack stands under the frame on both sides
  4. Remove hanger nuts to detach the spring from the frame
  5. Remove visible grime from spring leaves
  6. Apply generous treatment of Kano Penephite, possibly using a screwdriver head to get between the leaves
  7. Reinstall hanger nuts carefully using a torque wrench in a cross pattern
  8. Lower everything back down
  9. Install oiled spring cover (from Snyder's)
  10. Reattach brake rods and shock arms (good time to check the shocks too)

Does this look OK? Any improvements?
alexiskai is offline   Reply With Quote
Old 08-17-2019, 02:21 PM   #2
Brentwood Bob
Senior Member
 
Join Date: May 2010
Location: brentwood, ca
Posts: 4,214
Default Re: Sanity check on lubing springs in place

Where is the containment step in your sequence? C-clamps, or logging chain would do the job. I would do with step 4.
Brentwood Bob is online now   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 08-17-2019, 02:42 PM   #3
alexiskai
Senior Member
 
alexiskai's Avatar
 
Join Date: Apr 2018
Location: Mebane NC
Posts: 2,330
Default Re: Sanity check on lubing springs in place

Quote:
Originally Posted by Brentwood Bob View Post
Where is the containment step in your sequence? C-clamps, or logging chain would do the job. I would do with step 4.
Do I need to clamp the springs even though I'm not taking them out of the spring perches?
alexiskai is offline   Reply With Quote
Old 08-17-2019, 02:47 PM   #4
Bob Bidonde
Senior Member
 
Bob Bidonde's Avatar
 
Join Date: May 2010
Location: Long Island, NY
Posts: 3,432
Default Re: Sanity check on lubing springs in place

Don't take the springs apart.

> Have someone rock the car side-to-side and spray the springs on both sides with SAE 10 oil. Do this a few times after driving the car;

> Buy a set of spring covers and saturate the felt pads with 140 gear oil. Install the pads, and annually replenish the gear oil.

An immediate ride improvement can be had by reducing the rear tire pressures to 28 psig, and the front tire pressures to 30 psig.
Attached Images
File Type: jpg LEaf Spring Covers.jpg (3.2 KB, 633 views)
__________________
Bob Bidonde
Bob Bidonde is offline   Reply With Quote
Old 08-17-2019, 03:09 PM   #5
alexiskai
Senior Member
 
alexiskai's Avatar
 
Join Date: Apr 2018
Location: Mebane NC
Posts: 2,330
Default Re: Sanity check on lubing springs in place

There may be some confusion, I'm not planning to disassemble the springs. I'm just trying to lift the frame away from them slightly so that I can get up as close as possible to spray them with the lubricant. They're not coming off the axles.

I know there's a lot of cautionary tales out there about the stored energy in the springs, hence the recommendation of a spreader for the rear springs. What I'm trying to figure out is, am I OK just lifting the frame off them briefly without the spreader? Or do I need to do the lubrication with the frame in place, per Bob Bidonde's suggestion?
alexiskai is offline   Reply With Quote
Old 08-17-2019, 03:22 PM   #6
cjkohnast
Senior Member
 
Join Date: Jan 2017
Posts: 357
Default Re: Sanity check on lubing springs in place

Sponsored Links (Register now to hide all advertisements)
Do not detach anything. Put the car on jack stands just high enough to take weight off the tires maybe an inch take an old screwdriver and drive it between the leaves. spraying between each leaf.
cjkohnast is offline   Reply With Quote
Old 08-17-2019, 03:25 PM   #7
alexiskai
Senior Member
 
alexiskai's Avatar
 
Join Date: Apr 2018
Location: Mebane NC
Posts: 2,330
Default Re: Sanity check on lubing springs in place

OK, so that is now two votes for "don't take the U-bolts off." Good to know.
alexiskai is offline   Reply With Quote
Old 08-17-2019, 03:44 PM   #8
Brentwood Bob
Senior Member
 
Join Date: May 2010
Location: brentwood, ca
Posts: 4,214
Default Re: Sanity check on lubing springs in place

The center bolt can fail at any time, the best time would be when the spring is contained.
Brentwood Bob is online now   Reply With Quote
Old 08-17-2019, 03:55 PM   #9
alexiskai
Senior Member
 
alexiskai's Avatar
 
Join Date: Apr 2018
Location: Mebane NC
Posts: 2,330
Default Re: Sanity check on lubing springs in place

Sounds like I should just eliminate step #4, and in step #7 just tighten the hanger nuts, make sure they're even.
alexiskai is offline   Reply With Quote
Old 08-17-2019, 04:44 PM   #10
jb-ob
Senior Member
 
Join Date: Jun 2010
Posts: 631
Default Re: Sanity check on lubing springs in place

Alex,


Why all the work ??


1. Jack up the car placing jack stands under the front motor mounts.


2. Remove front wheels.


3. Lower the front axle until the shocks bottom out.


4. Soak the relaxed leaves with your favorite penetrating oil.


5. Jack her up & reinstall front wheels.


I used the same product, worked great for me.


JB
jb-ob is offline   Reply With Quote
Old 08-17-2019, 04:47 PM   #11
alexiskai
Senior Member
 
alexiskai's Avatar
 
Join Date: Apr 2018
Location: Mebane NC
Posts: 2,330
Default Re: Sanity check on lubing springs in place

I like this method, guess I should decide whether it's more work to take the wheels off or just to jack the frame up another foot, seems like it would have the same effect.
alexiskai is offline   Reply With Quote
Old 08-17-2019, 05:21 PM   #12
Terry, NJ
Senior Member
 
Terry, NJ's Avatar
 
Join Date: May 2010
Location: Bucks Co, Pa
Posts: 3,740
Default Re: Sanity check on lubing springs in place

Be Very careful of the springs! I'm sure that in the history of model A s, someone has been killed by the rear spring. I almost lost a leg to one. DO NOT LOOSEN the SPRING UNLESS YOU HAVE IT CONTAINED!
To return to the subject at hand, here's what I would do; With the body in place, loosen the center nut on the spring. Back it off no more than two turns. Now flood the little gaps between the leaves with motor oil in a squeeze can.Maybe jack the frame (not the wheels) a click or three and get as much oil in between the leaves as is possible. Then let it all down on the ground again and retighten the center bolt of the spring. This is far easier and less dangerous than messing around with the spring.
Terry
Attached Images
File Type: jpg 100_1701.jpg (121.8 KB, 67 views)
File Type: jpg 100_1703.jpg (34.6 KB, 64 views)
File Type: jpg 100_1697.jpg (105.9 KB, 74 views)

Last edited by Terry, NJ; 08-18-2019 at 11:52 AM.
Terry, NJ is offline   Reply With Quote
Old 08-17-2019, 07:03 PM   #13
midgetracer
Senior Member
 
midgetracer's Avatar
 
Join Date: May 2010
Location: Bismarck ND
Posts: 1,189
Default Re: Sanity check on lubing springs in place

How about using one of these gizmos.
Attached Images
File Type: jpg DSC00755.JPG (118.9 KB, 92 views)
midgetracer is offline   Reply With Quote
Old 08-17-2019, 07:13 PM   #14
alexiskai
Senior Member
 
alexiskai's Avatar
 
Join Date: Apr 2018
Location: Mebane NC
Posts: 2,330
Default Re: Sanity check on lubing springs in place

Not familiar with that gizmo, what is it?
alexiskai is offline   Reply With Quote
Old 08-17-2019, 07:24 PM   #15
Chuck Sea/Tac
Senior Member
 
Chuck Sea/Tac's Avatar
 
Join Date: May 2010
Location: Between Seattle & Tacoma
Posts: 2,351
Default Re: Sanity check on lubing springs in place

I just jack one end of the car at a time up high, enough so that jackstands under the frame will let the wheels and spring hang as far down as it’ll go. Then I use like a motorcycle chain lube or Teflon silicone, or a penetrating type oil squirted all around the leaves.
Chuck Sea/Tac is offline   Reply With Quote
Old 08-17-2019, 08:06 PM   #16
Kurt in NJ
Senior Member
 
Kurt in NJ's Avatar
 
Join Date: May 2010
Location: on the Littlefield
Posts: 6,140
Default Re: Sanity check on lubing springs in place

I use a simplified method--- take oil can, fill with atf, squirt on springs. Go for drive---- don't forget the oil hole in the hand crank bearing
Kurt in NJ is offline   Reply With Quote
Old 08-17-2019, 09:14 PM   #17
Tacoma Bob
Senior Member
 
Tacoma Bob's Avatar
 
Join Date: May 2010
Location: Tacoma, WA
Posts: 1,025
Default Re: Sanity check on lubing springs in place

Penephite is designed to travel horizontally.
Tacoma Bob is offline   Reply With Quote
Old 08-17-2019, 09:31 PM   #18
alexiskai
Senior Member
 
alexiskai's Avatar
 
Join Date: Apr 2018
Location: Mebane NC
Posts: 2,330
Default Re: Sanity check on lubing springs in place

Quote:
Originally Posted by Tacoma Bob View Post
Penephite is designed to travel horizontally.
Is that... bad? Isn't that the reason to use it on leaf springs?
alexiskai is offline   Reply With Quote
Old 08-17-2019, 09:56 PM   #19
Ranchero50
Senior Member
 
Join Date: Aug 2019
Location: Hagerstown MD
Posts: 224
Default Re: Sanity check on lubing springs in place

I'd just put some old motor oil in a squirt bottle, spray the spring packs and take it for a ride. Come home and wipe up any mess.

I had my rear spring apart The leaves don't relax until you remove the center bolt and start loosening the clamps.
Ranchero50 is offline   Reply With Quote
Old 08-17-2019, 11:01 PM   #20
midgetracer
Senior Member
 
midgetracer's Avatar
 
Join Date: May 2010
Location: Bismarck ND
Posts: 1,189
Default Re: Sanity check on lubing springs in place

Quote:
Originally Posted by alexiskai View Post
Not familiar with that gizmo, what is it?
It is a tool to lubricate leaf springs.
midgetracer is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 02:20 PM.