|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
05-17-2012, 08:19 PM | #1 |
Senior Member
Join Date: May 2010
Location: Sugar Land, TX
Posts: 4,395
|
Wood graining by gunstock process
I just got my 36 woodie dash back after being wood grained by the water transfer printing process. It looks nice and cost much less than the old fashioned way. They lay the wood grain photo on top of water. Then the result is clear coated. Cost was $270 including return shipping for dash, windshield trim, and ash tray face. The place I picked was very slow and I wouldn't recommend them but the results were good. They neglected to wood grain the waterfall I sent them. I'll email and see what their excuse is.
Here is a video about how it is done although this is not the place I sent mine. https://www.youtube.com/watch?v=5iUCp...eature=related Last edited by mrtexas; 05-17-2012 at 08:28 PM. |
05-17-2012, 09:14 PM | #2 |
Senior Member
Join Date: May 2010
Location: norcal
Posts: 173
|
Re: Wood graining by gunstock process
thats the way to go, i loved the dashes i saw at a recent swap meet, but $700 and it did not include the window garnish ?.
thanks rich |
Sponsored Links (Register now to hide all advertisements) |
|
05-17-2012, 11:09 PM | #3 |
Senior Member
Join Date: May 2010
Location: Daytona Beach, Fl & Spencer, W. Va,
Posts: 4,442
|
Re: Wood graining by gunstock process
This looks really good to me !
I think it beats the hand-done ones, in both looks and price. MIKE |
05-21-2012, 01:43 PM | #4 |
Senior Member
Join Date: May 2010
Location: Sugar Land, TX
Posts: 4,395
|
Re: Wood graining by gunstock process
Here is their reply on the waterfall wood graining:
"We did not do the chrome piece because we were concerned that when blasting the chrome off we would also being taking it off the raise areas. We could have just base coated and printed right over the chrome but could not guarantee it would stay. Please let us know if there questions." The company I used is http://www.georgiahydrographics.com/ I ended up with no woodgraining on the waterfall. That is OK with me but I would have preferred they do it. I wouldn't recommend this company. Perhaps there is a better one. Their clear coat over the wood graining wasn't show quality but I paid a lot less than the old fashioned way. Perhaps they aren't very experienced in car dash woodgraining. I wouldn't hesitate to use the process again as it is a good look and much cheaper. |
05-22-2012, 06:47 PM | #5 |
Senior Member
Join Date: May 2010
Location: Sydney, Australia
Posts: 108
|
Re: Wood graining by gunstock process
How well did the "grains" line up between the glove box door and the rest of the dash?
robert1936 |
05-22-2012, 07:37 PM | #6 |
Senior Member
Join Date: May 2010
Location: Sugar Land, TX
Posts: 4,395
|
Re: Wood graining by gunstock process
|
05-23-2012, 09:58 AM | #7 |
Senior Member
Join Date: May 2010
Posts: 362
|
Re: Wood graining by gunstock process
You can grain the waterfall yourself. Tape off the raised areas and then use an adhesion promoter, followed by the base coat. Get some gel stain to match the grain color and apply it with an artists brush, leaving brush marks. Now go over the stain with a dry brush and an unsteady hand (comes naturally to me) and make your grain pattern. The fan type brushes seem to work better at creating a grain pattern. You can also use a dragging brush, but they are usually to big for the waterfall. They are sold where faux painting supplies are sold.
__________________
TomO |
|
|
Sponsored Links (Register now to hide all advertisements) |
|