|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
05-18-2019, 08:01 AM | #1 |
Senior Member
Join Date: May 2010
Location: At my kitchen table in Santa Rosa, Ca
Posts: 2,903
|
step plate location
Hi! i have a Friend that has a 29 Roadster pickup, he has some step plates for it, and would like to put them on. But he is not sure where to put them.Do they go center of the running board? could you guys let me know
__________________
If it would have been a snake it would have bit ya! i can't spell my way out of a paper bag! |
05-18-2019, 08:13 AM | #2 |
Senior Member
Join Date: May 2010
Location: Michigan
Posts: 580
|
Re: step plate location
Put them best where you foot lands getting in and out. I have them centered between the apron and edge of running board on my 31 Pickup.
|
Sponsored Links (Register now to hide all advertisements) |
|
05-18-2019, 08:24 AM | #3 |
Senior Member
Join Date: May 2010
Location: Spruce Pine, NC
Posts: 1,458
|
Re: step plate location
my favorite location is: hanging on the garage wall......
__________________
our next Model A is out there in the unknown...... |
05-18-2019, 08:33 AM | #4 |
Senior Member
Join Date: May 2010
Location: Alabama
Posts: 8,099
|
Re: step plate location
I agree !!!
|
05-18-2019, 09:15 AM | #5 |
Senior Member
Join Date: Dec 2014
Location: Shawnee, Ok
Posts: 3,471
|
Re: step plate location
Look for the wear spot on your running board, that's where they go
__________________
Keith Shawnee OK '31 SW 160-B |
05-18-2019, 09:20 AM | #6 |
Senior Member
Join Date: May 2010
Location: Alabama
Posts: 8,099
|
Re: step plate location
Sponsored Links (Register now to hide all advertisements)
|
05-18-2019, 11:10 AM | #7 |
Senior Member
Join Date: Jun 2013
Location: Western Springs, IL
Posts: 324
|
Re: step plate location
They are not only a step plate, but a scuff guard to keep you from kicking the splash apron and scratching the paint.
|
05-18-2019, 01:53 PM | #8 |
Senior Member
Join Date: Jun 2013
Location: Marana Arizona
Posts: 1,776
|
Re: step plate location
My 30 Tudor came with step plates. They are located 10 1/4 inch back from front edge of rubber trim and the bottom of the plate is 3/4 of an inch from the outside edge of the running board. Chap
|
05-18-2019, 04:00 PM | #9 |
Senior Member
Join Date: May 2010
Location: Michigan
Posts: 580
|
Re: step plate location
|
05-19-2019, 07:31 AM | #10 |
Senior Member
Join Date: May 2010
Location: Mpls, MN
Posts: 27,582
|
Re: step plate location
|
05-19-2019, 07:53 AM | #11 |
Senior Member
Join Date: Mar 2014
Location: Midland Park,N.J.
Posts: 1,108
|
Re: step plate location
On my 29ccpu I put them on top of the running board worn spot.
|
05-19-2019, 08:37 AM | #12 |
Senior Member
Join Date: Dec 2010
Location: FRESNO, CA
Posts: 12,560
|
Re: step plate location
Chief, my Dad, put them backwards, for MUD scrapers!
Bill W.
__________________
"THE ASSISTANT GURU OF STUFF" |
|
|
Sponsored Links (Register now to hide all advertisements) |
|