|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
03-16-2011, 07:26 PM | #1 |
Senior Member
Join Date: May 2010
Location: Northern New Jersey
Posts: 1,262
|
30-31 cc pickup info needed
Can anyone send or post me a photo of what the rear body cross channel on a 30 CC Pick-up should look like. Mine is swiss cheese and the rear edge is Bondo'd to the lower back edge of the cab. Is this part reproduced ? Can it be installed without disassembling the cab ?
|
03-16-2011, 08:22 PM | #2 |
Senior Member
Join Date: May 2010
Location: Clinton,WA/Whidbey Island
Posts: 4,104
|
Re: 30-31 cc pickup info needed
If you have a brattons cat. check pick up parts. Is what your looking for part of frame or cab?
__________________
www.whidbeymodelaclub.com |
Sponsored Links (Register now to hide all advertisements) |
|
03-16-2011, 11:06 PM | #3 |
Senior Member
Join Date: May 2010
Location: Takoma park md
Posts: 271
|
Re: 30-31 cc pickup info needed
ive been doing that repair i will post pics in the morning , its complicated and careful work . also the repro cross channel needs a couple of extra reworks to it to make it like the original, including fabbing the ends to connect to the door post bottoms and redrilling for holes put in at the wrong places and adding ones that were not put in at all but are on the original . plus of course there is the patch panels that also need to be installed for the cab back and corners . im taking it slow and getting all the pieces cut and fit before welding and than there is the interior rust that will be revealed when you get that swiss cheese out of the way. lovely work.. just take your time and make it as right as your skills can give it . pics on thursday day.
edit sorry for the delay much juggling in the shop these days. here are the pics and by way of explanation note the differences in the end of the repro piece and what was added to it also the repro was not as wide as needed so i had to open the corner so it would reach the post . also note that if i did not add the end connecter the corner patch would have no where to be tack welded on, the cab back and corners all tack weld to the bottom edge of the cross member, the repro also need hole to be redrilled for correct alignment as well as for adding holes that were not put in at all . hope this helps
__________________
Rust and roll will never die Last edited by rollingsculpture; 03-19-2011 at 12:33 PM. Reason: add pics |
03-18-2011, 11:39 AM | #4 |
Senior Member
Join Date: May 2010
Location: Northern New Jersey
Posts: 1,262
|
Re: 30-31 cc pickup info needed
Gary it is part of the sub-frame on the cab....
|
03-18-2011, 06:46 PM | #5 |
Senior Member
Join Date: May 2010
Location: Michigan
Posts: 1,593
|
Re: 30-31 cc pickup info needed
Here are three pics of what you asked about.
|
03-19-2011, 12:38 PM | #6 |
Senior Member
Join Date: May 2010
Location: Takoma park md
Posts: 271
|
Re: 30-31 cc pickup info needed
Sponsored Links (Register now to hide all advertisements)
__________________
Rust and roll will never die |
03-20-2011, 06:51 PM | #7 |
Junior Member
Join Date: Feb 2011
Location: Metcalfe, ON, Canada
Posts: 14
|
Re: 30-31 cc pickup info needed
Hi, in looking at the pictures you posted, I was wondering what the dimension from front to back of the crossmember. I have restored a Late '31 CC pickup. I ordered a new crossmember from Snyder's and it was too narrow. I had a new one fabricated to match the original. Snyder's told me that there should be only one size of crossmember. Thanks, Denis.
|
03-21-2011, 07:38 PM | #8 |
Senior Member
Join Date: May 2010
Location: Takoma park md
Posts: 271
|
Re: 30-31 cc pickup info needed
hello baxter , this thread is about the rear sub cross member there is also the center one which is much narrower and not rounded at the back here are pics of what i have been working on . the dimensions are 45 1/2 inch wide and 6 5/8 deep which includes the 5/8 flange for the floor pan.
__________________
Rust and roll will never die |
|
|
Sponsored Links (Register now to hide all advertisements) |
|