|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
04-18-2019, 11:50 PM | #1 |
Senior Member
Join Date: May 2010
Location: Sacramento, CA
Posts: 216
|
10 leaf rear springs
Absent the original springs clamps that were stamped with the spring assembly part number, is there a way to distinguish rear springs for pick-ups, wagons and deliveries (Part#A-5560-E) from the Fordor springs (Part#A-5560-D)?
|
04-19-2019, 07:10 AM | #2 |
Senior Member
Join Date: Jul 2010
Location: Cow Hampshire
Posts: 4,188
|
Re: 10 leaf rear springs
One has to break down the springs into the elemental leaves, and then measure the leaf thickness leaf by leaf.
Marco has a chart which outlines the thicknesses which you might see. There actually were not that many individual variants on leaves. 12 comes to mind. And even less variant on thicknesses (4) but from this Ford made up spring packs for everything from roadsters to pickup trucks. See https://fordbarn.com/forum/showthread.php?t=16271 It is possible to measure leaf thicknesses off the ends of the spring-ends using a depth micrometer and generous intuition regarding tip wear/grooving of the leaves. Should you decide to break down a spring-pack so that you can measure more accurately with a micrometer, BE WARY as you undo or cut with a grinder that center bolt. There can be considerable pent up energy even in a "removed" spring, and the upper half of a spring pack has been known to "jump" when the bolt is cut. My parents dining room floor joints took a jolt when my spring pack "took flight" from where they were being held in my vise in the basement. Parents weren't home, fortunately, and I myself was startled but unhurt in the surprise. (called lucky!) Others report no problemo here but the difference may be the difference between a roadster spring and a pickup spring, this latter being my experience. Replacement center bolts are provided "long" so that one may safely restore this pre-loading during assembly. It is not a bad idea to replace a center bolt in restoration simply because an occasional center bolt is found "broken" which complicates servicing and removal of a rear axle later. Joe K
__________________
Shudda kept the horse. Last edited by Joe K; 04-19-2019 at 07:25 AM. |
Sponsored Links (Register now to hide all advertisements) |
|
04-19-2019, 09:33 AM | #3 |
Senior Member
Join Date: May 2010
Location: Sacramento, CA
Posts: 216
|
Re: 10 leaf rear springs
Joe,
Thanks for the lead. A friend had a center bolt and spring go through his garage roof back in high school days. That experience has remained whenever I fool with any spring assemblies. |
04-19-2019, 10:19 AM | #4 |
Senior Member
Join Date: May 2010
Location: Southern California
Posts: 7,032
|
Re: 10 leaf rear springs
I use a roadster spring (7 leafs if I remember correctly) in my '31 RDPU. Better ride and the tire is better centered in the fender.
Charlie Stephens |
04-19-2019, 10:46 AM | #5 |
Senior Member
Join Date: Jun 2010
Location: Temecula, CA
Posts: 4,088
|
Re: 10 leaf rear springs
If you are not going to use it as a work truck, do as Charlie did, you'll be happier.
|
04-19-2019, 11:56 AM | #6 |
Senior Member
Join Date: May 2010
Posts: 226
|
Re: 10 leaf rear springs
Sponsored Links (Register now to hide all advertisements)
Download the PDF file to get Marco's complete spring chart that includes witch spring goes on witch body type. |
04-19-2019, 12:29 PM | #7 |
Senior Member
Join Date: Dec 2014
Location: Germantown,TN
Posts: 516
|
Re: 10 leaf rear springs
I have a roadster spring in my CCPU. Ride is much improved.
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|