Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 01-13-2019, 09:02 PM   #1
modeleh
Senior Member
 
modeleh's Avatar
 
Join Date: May 2010
Location: Nanaimo BC
Posts: 242
Default Weiand 8.75 Heads

I have a set of Weiand heads 8.75 stamped at water neck. They are 59a style so I presume the CR was calculated based on a 239. What are your opinions on installing them on a 8ba standard bore with 4” crank? I have read that Flatheads don’t work great past around 9:1
If a guy were to build a 276 would you run these heads?
modeleh is offline   Reply With Quote
Old 01-13-2019, 09:23 PM   #2
qmdv
Senior Member
 
qmdv's Avatar
 
Join Date: Dec 2012
Location: Payette, ID
Posts: 935
Default Re: Weiand 8.75 Heads

Some times when the CR gets to high it is call hopping them down. Here is an old Ed Winfield story. A kid I knew growing up had a 1/4 midget back in the late 50's. His dad knew Ed Winfield very well. I forgot what engine he had. Some sort of flathead that met size spec. Well Winfield ported and relieved it and did a cam upgrade. This kid was always winning. He got older and interested in other things so the 1/4 midget was sold. New owners kid was then a consistent winner. They tore it down and checked CR and was surprised how low it was. So the head was milled to get CR up and that ruined the breathing characteristics. Maybe call it a Tune Down. It quit winning.
qmdv is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 01-13-2019, 09:35 PM   #3
modeleh
Senior Member
 
modeleh's Avatar
 
Join Date: May 2010
Location: Nanaimo BC
Posts: 242
Default Re: Weiand 8.75 Heads

Interesting story. It makes you wonder how many sets of aluminum heads have been installed that have improved the appearance of the engine but diminished the performance. I have a set of EAB heads, maybe they are a better choice.
modeleh is offline   Reply With Quote
Old 01-13-2019, 10:18 PM   #4
34fivewindow
Senior Member
 
34fivewindow's Avatar
 
Join Date: May 2010
Location: Santa Rosa, Calif.
Posts: 376
Default Re: Weiand 8.75 Heads

Quote:
Originally Posted by qmdv View Post
Some times when the CR gets to high it is call hopping them down. Here is an old Ed Winfield story. A kid I knew growing up had a 1/4 midget back in the late 50's. His dad knew Ed Winfield very well. I forgot what engine he had. Some sort of flathead that met size spec. Well Winfield ported and relieved it and did a cam upgrade. This kid was always winning. He got older and interested in other things so the 1/4 midget was sold. New owners kid was then a consistent winner. They tore it down and checked CR and was surprised how low it was. So the head was milled to get CR up and that ruined the breathing characteristics. Maybe call it a Tune Down. It quit winning.
That sounds like Kong Jackson’s kid with the winning quarter midget, i raced quarter midgets against that kid in 1956-57.
34fivewindow is offline   Reply With Quote
Old 01-13-2019, 11:39 PM   #5
Ol' Ron
Senior Member
 
Ol' Ron's Avatar
 
Join Date: May 2010
Location: Chester Vt
Posts: 8,841
Default Re: Weiand 8.75 Heads

What ever the stamped CR is: You might want to cc the chamber before you worry about the actual compression. Now how much cam lift will clear the head. At least you;ll have something to work with.
Ol' Ron is offline   Reply With Quote
Old 01-14-2019, 01:04 AM   #6
Pete
Senior Member
 
Pete's Avatar
 
Join Date: May 2010
Location: Wa.
Posts: 5,373
Default Re: Weiand 8.75 Heads

Sponsored Links (Register now to hide all advertisements)
Quote:
Originally Posted by modeleh View Post
I have a set of Weiand heads 8.75 stamped at water neck. They are 59a style so I presume the CR was calculated based on a 239. What are your opinions on installing them on a 8ba standard bore with 4” crank? I have read that Flatheads don’t work great past around 9:1
If a guy were to build a 276 would you run these heads?
To use them on an 8ba block, you need to plug a small water hole on each deck.
It will be obvious when you lay an early big bore head gasket down.

Flatheads work great at 15 to 1, but 8 to 1 is a good street number.

Those heads will work fine on a 276 as long as you check for valve and piston clearance, flatness and make sure the fire ring does not hang over anywhere.

Also check the plugs you will run to see that there are no sharp thread edges exposed in the chamber. Adjust plug depth with solid copper washers intended for that, if need be. You should be using solid copper washers anyway.
Pete is offline   Reply With Quote
Old 01-14-2019, 07:15 AM   #7
flathead4rd
Senior Member
 
flathead4rd's Avatar
 
Join Date: May 2010
Location: Michigan
Posts: 501
Default Re: Weiand 8.75 Heads

15 to 1 ? What are the specs on that flathead
flathead4rd is offline   Reply With Quote
Old 01-14-2019, 08:30 AM   #8
modeleh
Senior Member
 
modeleh's Avatar
 
Join Date: May 2010
Location: Nanaimo BC
Posts: 242
Default Re: Weiand 8.75 Heads

Thank you Ron and Pete, I was hoping that you guys would comment, I really appreciate the advice you offer on this forum. I’m going to try them first on a 255 with a Schneider s-100 and edelbrock with four 81s. The block is relieved so that would help to diminish CR slightly. I will cc them, clay, adjust plug depth as suggested. Cheers.

Last edited by modeleh; 01-14-2019 at 08:46 AM.
modeleh is offline   Reply With Quote
Old 01-14-2019, 09:45 PM   #9
Pete
Senior Member
 
Pete's Avatar
 
Join Date: May 2010
Location: Wa.
Posts: 5,373
Default Re: Weiand 8.75 Heads

Quote:
Originally Posted by flathead4rd View Post
15 to 1 ? What are the specs on that flathead
...
Attached Images
File Type: jpg FLATHEAD ENGINE FRONT LEFT.jpg (19.3 KB, 85 views)
Pete is offline   Reply With Quote
Old 01-14-2019, 10:40 PM   #10
40 Deluxe
Senior Member
 
Join Date: May 2010
Location: now Kuna, Idaho
Posts: 3,774
Default Re: Weiand 8.75 Heads

Quote:
Originally Posted by Pete View Post
...
Out of breath at 46-4800 RPM? That's a lot of cubes to feed through those restrictive intake ports! Or are the ports realigned, relocated, welded, epoxied, etc.?
40 Deluxe is offline   Reply With Quote
Old 01-14-2019, 10:47 PM   #11
Tinker
Senior Member
 
Tinker's Avatar
 
Join Date: May 2010
Location: MN
Posts: 7,053
Default Re: Weiand 8.75 Heads

Quote:
Originally Posted by Ol' Ron View Post
What ever the stamped CR is: You might want to cc the chamber before you worry about the actual compression. Now how much cam lift will clear the head. At least you;ll have something to work with.

good idea on a unknown set of heads, to understand if they have been previously milled. Over milled vintage heads are not uncommon. Guess you could stack gaskets as a "fix"

Last edited by Tinker; 01-14-2019 at 10:59 PM.
Tinker is offline   Reply With Quote
Old 01-14-2019, 11:34 PM   #12
Pete
Senior Member
 
Pete's Avatar
 
Join Date: May 2010
Location: Wa.
Posts: 5,373
Default Re: Weiand 8.75 Heads

Quote:
Originally Posted by 40 Deluxe View Post
Out of breath at 46-4800 RPM? That's a lot of cubes to feed through those restrictive intake ports! Or are the ports realigned, relocated, welded, epoxied, etc.?
No welding etc on intakes.
Hp peak at 6500. 328 on straight alcohol.
Pete is offline   Reply With Quote
Old 01-15-2019, 12:11 AM   #13
40 Deluxe
Senior Member
 
Join Date: May 2010
Location: now Kuna, Idaho
Posts: 3,774
Default Re: Weiand 8.75 Heads

Quote:
Originally Posted by Pete View Post
No welding etc on intakes.
Hp peak at 6500. 328 on straight alcohol.
Impressive! I stand corrected. Do you have any videos/film with sound? Any build data you care to share? Thanks!
40 Deluxe is offline   Reply With Quote
Old 01-15-2019, 07:37 AM   #14
john in illinois
Senior Member
 
john in illinois's Avatar
 
Join Date: May 2010
Location: Illinois
Posts: 2,181
Default Re: Weiand 8.75 Heads

Modeleh here is a chart that might be helpful after you cc the head.

https://web.archive.org/web/20160318.../compratio.htm

John
john in illinois is offline   Reply With Quote
Old 01-15-2019, 01:04 PM   #15
modeleh
Senior Member
 
modeleh's Avatar
 
Join Date: May 2010
Location: Nanaimo BC
Posts: 242
Default Re: Weiand 8.75 Heads

Thanks John that’s good information I haven’t seen posted before.
modeleh is offline   Reply With Quote
Old 01-15-2019, 01:23 PM   #16
Ol' Ron
Senior Member
 
Ol' Ron's Avatar
 
Join Date: May 2010
Location: Chester Vt
Posts: 8,841
Default Re: Weiand 8.75 Heads

charts are good, but can be misleading. The combustion chamber is much larger than just the head volume, like the head gasket, piston to head clearance, valve eye brows and a relief if you have one.. I add 15cc's to the head volume just for kicks. At least it's closer to reality.
Ol' Ron is offline   Reply With Quote
Old 01-15-2019, 01:36 PM   #17
tubman
Senior Member
 
tubman's Avatar
 
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,259
Default Re: Weiand 8.75 Heads

I bought a burette I don't use anymore. I have found that aluminum foil balls held in place by a bit of grease and bolt the heads on to be a much better indication of what's really going on. The last set of Edmunds 8BA heads turned out needing to be "angle-milled" from .040 on one end to .000 the other to bring the combustion chambers into spec. A couple of test fittings made the problem become obvious (the block had been decked incorrectly). This engine has been running strong for the last two years and several thousand miles..
tubman is online now   Reply With Quote
Old 01-15-2019, 04:49 PM   #18
modeleh
Senior Member
 
modeleh's Avatar
 
Join Date: May 2010
Location: Nanaimo BC
Posts: 242
Default Re: Weiand 8.75 Heads

Both good points.
I like the idea of the foil balls. What is the recommended minimum clearance from piston crown to head and from open valve to head?
modeleh is offline   Reply With Quote
Old 01-15-2019, 06:44 PM   #19
tubman
Senior Member
 
tubman's Avatar
 
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,259
Default Re: Weiand 8.75 Heads

.045"-.050" for piston crown to head, and .060 over the valves (I don't run wild cams and have never even been close over the valves). For a street engine, I like to be on the high side. In addition to increasing the compression ratio, it promotes better combustion of the fuel/air mixture because it optimizes the "squish" area above the piston. For more detail, there are many threads, both on here and on the H.A.M.B. An increase in compression is always helpful in increasing performance AND fuel economy. Given today's fuels, we shouldn't be constrained to the stock Ford compression ratios, that were 7.2:1 at their best. May be the restoration guys would like to, but if you actually drive your cars, It's the way to go.
tubman is online now   Reply With Quote
Old 01-16-2019, 08:48 PM   #20
Tinker
Senior Member
 
Tinker's Avatar
 
Join Date: May 2010
Location: MN
Posts: 7,053
Default Re: Weiand 8.75 Heads

If you look at the Model A forum, most run "touring" engines. Restoration doesn't mean you can't shave a head, if it's the right head and it works.

Trial and error! You'll figure it out.




.
Tinker is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 11:43 AM.