Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 11-17-2019, 02:10 PM   #1
Werner
Senior Member
 
Werner's Avatar
 
Join Date: Jan 2019
Location: Germany, near Aachen
Posts: 798
Default Remove inner oil pan

Hallo,
does anyone have a suggestion how I pull out the corrugated iron insert-pan off the whole oil pan? (Tiny rust holes!)
Attached Images
File Type: jpg P1010356.jpg (51.0 KB, 67 views)
__________________
Beste Gruesse aus Deutschland,
Werner


Ford Model A Roadster, 1928
Citroen 11 CV, 1947
Hercules NSU-Wankel Rotary Engine, 1976 (Canadian version)

Last edited by Werner; 11-17-2019 at 02:24 PM.
Werner is offline   Reply With Quote
Old 11-17-2019, 02:12 PM   #2
dbaldwi3
Member
 
dbaldwi3's Avatar
 
Join Date: Oct 2018
Location: Gulf coast of florida
Posts: 52
Default Re: Remove inner oil pan

Believe it or not a Wooden baseball bat slid into the side and give it a good pop it will come out.
dbaldwi3 is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 11-17-2019, 02:17 PM   #3
john charlton
Senior Member
 
john charlton's Avatar
 
Join Date: May 2010
Posts: 835
Default Re: Remove inner oil pan

Put a piece of old junk carpet on the ground and drop the pan upside down on the carpet it will just pop out . You might have to assist gravity a litle bit .Dont do it on bare concrete .

John in no weather today Suffolk County England .
john charlton is offline   Reply With Quote
Old 11-17-2019, 02:36 PM   #4
Dick M
Senior Member
 
Dick M's Avatar
 
Join Date: May 2010
Location: hidden valley lake, ca
Posts: 348
Send a message via Yahoo to Dick M
Default Re: Remove inner oil pan

Best to put the pan in a plastic garbage bay prior to dropping. It will contain the sludge!!
Dick M is offline   Reply With Quote
Old 11-17-2019, 03:17 PM   #5
Tom Endy
Senior Member
 
Tom Endy's Avatar
 
Join Date: May 2010
Location: Southern California
Posts: 2,611
Default Re: Remove inner oil pan

Quote:
Originally Posted by dbaldwi3 View Post
Believe it or not a Wooden baseball bat slid into the side and give it a good pop it will come out.
A baseball bat works well. If you don't have a baseball bat handy a hammer with a wooden handle will also work. Insert the handle into the hole for the oil pump. put you foot on the pan to stabilize it and give it a jerk, it will come out.

Tom Endy
Tom Endy is offline   Reply With Quote
Old 11-17-2019, 03:49 PM   #6
Kurt in NJ
Senior Member
 
Kurt in NJ's Avatar
 
Join Date: May 2010
Location: on the Littlefield
Posts: 5,161
Default Re: Remove inner oil pan

if you slip the other side under the overhang of a step ---arm of the lift, or watever is handy to hold the pan then the baseball bat gives more control ---less splashing of gook
Kurt in NJ is offline   Reply With Quote
Old 11-17-2019, 04:00 PM   #7
The Master Cylinder
Senior Member
 
The Master Cylinder's Avatar
 
Join Date: Aug 2012
Location: SoCal
Posts: 458
Default Re: Remove inner oil pan

Hmmm, do they have baseball bats in Germany??
__________________
The Master Cylinder

Enjoying life at the beach in SoCal...
The Master Cylinder is offline   Reply With Quote
Old 11-17-2019, 04:05 PM   #8
Ed in Maine
Senior Member
 
Join Date: May 2010
Posts: 682
Default Re: Remove inner oil pan

The easiest of all way is to place a C-clamp inside the oil pump opening and lay a 2x4 in. piece of wood across the top of the oil pan. Simply wind up the C-clamp and out pops the dipper try. Ed
Ed in Maine is offline   Reply With Quote
Old 11-17-2019, 09:46 PM   #9
History
Senior Member
 
History's Avatar
 
Join Date: Oct 2017
Location: NC Mountains
Posts: 456
Default Re: Remove inner oil pan

Quote:
Originally Posted by Ed in Maine View Post
The easiest of all way is to place a C-clamp inside the oil pump opening and lay a 2x4 in. piece of wood across the top of the oil pan. Simply wind up the C-clamp and out pops the dipper try. Ed
That's the way I'd read but couldn't remember, excellent idea.
History is offline   Reply With Quote
Old 11-17-2019, 11:00 PM   #10
PalAl
Senior Member
 
PalAl's Avatar
 
Join Date: Jul 2016
Location: Orangeville Illinois
Posts: 246
Default Re: Remove inner oil pan

I do it this way and it is sooooo easy
Attached Images
File Type: jpg IMG_1182 oil pan baffle.jpg (48.1 KB, 140 views)
File Type: jpg IMG_1183 oil pan baffle.jpg (43.4 KB, 130 views)
PalAl is offline   Reply With Quote
Old 11-17-2019, 11:04 PM   #11
PalAl
Senior Member
 
PalAl's Avatar
 
Join Date: Jul 2016
Location: Orangeville Illinois
Posts: 246
Default Re: Remove inner oil pan

Make sure when you replace the baffle it snaps totaly in place, check and double check! You do not want to drop the pan for a do over.
PalAl is offline   Reply With Quote
Old 11-18-2019, 11:03 AM   #12
PalAl
Senior Member
 
PalAl's Avatar
 
Join Date: Jul 2016
Location: Orangeville Illinois
Posts: 246
Default Re: Remove inner oil pan

Remove slot screw plug and insert holder, remember to remove holder and insert plug when job is complete.
Here is another version of the holder
Attached Images
File Type: jpg Oil Pump Screw.jpg (13.3 KB, 6 views)
File Type: jpg Oil Pump Holder 2.jpg (24.0 KB, 6 views)
PalAl is offline   Reply With Quote
Old 11-18-2019, 11:04 AM   #13
PalAl
Senior Member
 
PalAl's Avatar
 
Join Date: Jul 2016
Location: Orangeville Illinois
Posts: 246
Default Re: Remove inner oil pan

Whoops... wrong thread...LOL
PalAl is offline   Reply With Quote
Old 12-10-2019, 02:38 PM   #14
Werner
Senior Member
 
Werner's Avatar
 
Join Date: Jan 2019
Location: Germany, near Aachen
Posts: 798
Default Re: Remove inner oil pan

I did it similar to PalAl. That worked well, thanks for the hint!

Again, it is easy to see how clean the interior of a motor is, if it is lubricated with HD oil SC. Minimal hardly any residues in the oil pan.
Attached Images
File Type: jpg P1100513.jpg (77.0 KB, 51 views)
__________________
Beste Gruesse aus Deutschland,
Werner


Ford Model A Roadster, 1928
Citroen 11 CV, 1947
Hercules NSU-Wankel Rotary Engine, 1976 (Canadian version)
Werner is offline   Reply With Quote
Old 12-10-2019, 06:02 PM   #15
CWPASADENA
Senior Member
 
CWPASADENA's Avatar
 
Join Date: May 2010
Location: PASADENA, CA
Posts: 1,430
Default Re: Remove inner oil pan

The last time I needed to remove the dipper tray from an oil pan, I had a 28-29 headlight bar on the bench that I tried to see if it would be a good pry bar. The curve on the end and the flange for the mounting bolts works perfectly as a pry bar. Use your foot on the pan and with the headlight bar, the dipper tray will pop right out.


My experience,


Chris W.
CWPASADENA is offline   Reply With Quote
Old 12-10-2019, 08:26 PM   #16
David R.
Senior Member
 
Join Date: Aug 2016
Location: West Virginia
Posts: 262
Default Re: Remove inner oil pan

I did like John said: tied it up in trash bag, held it up about head high, dropped it top side down on a piece of plywood on concrete driveway and popped right out first try. Boy was it grungy though!
David R. is offline   Reply With Quote
Old 12-11-2019, 07:51 AM   #17
davehc
Senior Member
 
davehc's Avatar
 
Join Date: Aug 2012
Location: Adrian , Mich.
Posts: 373
Default Re: Remove inner oil pan

12-01-2018, 03:59 PM #1 davehc
Senior Member



Join Date: Aug 2012
Location: Adrian , Mich.
Posts: 362


Easy Oil Pan Baffel Removel
Thought I would share how I removed the baffle from my oil pan after I finally got if off , for those who haven't tried this yet . . I used my slide hammer with the small hook , with a rubber cap to protect the baffle , hooked it in the small hole side of the baffle , and it popped out on the second slide .
Attached Thumbnails
davehc is offline   Reply With Quote
Old 12-11-2019, 02:20 PM   #18
Jim Brierley
Senior Member
 
Join Date: Jun 2010
Location: Temecula, CA
Posts: 3,257
Default Re: Remove inner oil pan

When you have the dipper tray out and cleaned, hold it up so sunlight will shine on it and check for rusted through spots. Water will settle in the dipper troughs and rust them.
Jim Brierley is offline   Reply With Quote
Old 12-11-2019, 03:15 PM   #19
Werner
Senior Member
 
Werner's Avatar
 
Join Date: Jan 2019
Location: Germany, near Aachen
Posts: 798
Default Re: Remove inner oil pan

Guten Abend Jim,
here at this point I have to enjoy myself. When I had the tub solved yesterday, I saw some rough areas (like rice) below. I soldered them hard today!
Attached Images
File Type: jpg P1100523.jpg (56.6 KB, 35 views)
__________________
Beste Gruesse aus Deutschland,
Werner


Ford Model A Roadster, 1928
Citroen 11 CV, 1947
Hercules NSU-Wankel Rotary Engine, 1976 (Canadian version)
Werner is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 04:30 AM.