Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 05-23-2020, 08:51 AM   #1
Bob Bidonde
Senior Member
 
Bob Bidonde's Avatar
 
Join Date: May 2010
Location: Long Island, NY
Posts: 1,714
Default Wind Wing Glass - Closed Car

I just bought a set of wind wings for my Victoria. The brackets come with a roll of glass setting rubber. My thought is that the setting material and glass need to be glued into each bracket.
What have you used to set the wing wing glasses?
Attached Images
File Type: jpg A-18200-C Wind Wing Brackets.jpg (13.7 KB, 39 views)
__________________
Bob Bidonde
Bob Bidonde is offline   Reply With Quote
Old 05-23-2020, 10:57 AM   #2
BRENT in 10-uh-C
Senior Member
 
BRENT in 10-uh-C's Avatar
 
Join Date: May 2010
Location: Eastern Tennessee
Posts: 9,216
Default Re: Wind Wing Glass - Closed Car

Bob, these are not manufactured correctly, and so the only way I have ever been able to successfully make them stay is to mill a slot in the brackets and clamps supplied to accept the wind wing rubber with the protrusions (link below). You will need to modify these too but it does grip well and the clamping force this allows you is all that is needed.


https://www.snydersantiqueauto.com/P...earchByKeyword
__________________
.

BRENT in 10-uh-C
.
www.model-a-ford.com
...(...Finally Updated!! )

.
BRENT in 10-uh-C is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 05-23-2020, 11:19 PM   #3
SSsssteamer
Senior Member
 
SSsssteamer's Avatar
 
Join Date: Nov 2010
Location: Sedro-Woolley, WA
Posts: 987
Default Re: Wind Wing Glass - Closed Car

Once the glass is captured between the wind wing brackets, there is no way for it to fall out. I have had mind on my '29 Tudor for 52 years now with out any problems. I wouldn't leave home without them. I did resent them sending Phillips head screws for their installation rather than the correct slotted headed screws. Hopefully 52 years later, that by now they have it corrected.
SSsssteamer is offline   Reply With Quote
Old Yesterday, 10:23 AM   #4
Joop
Senior Member
 
Joop's Avatar
 
Join Date: May 2010
Location: Glendale, AZ
Posts: 2,406
Default Re: Wind Wing Glass - Closed Car

.
I see you have a phaeton SSSSsteamer Bob is talking about a closed car his Victoria.
Joop is offline   Reply With Quote
Old Yesterday, 08:04 PM   #5
SSsssteamer
Senior Member
 
SSsssteamer's Avatar
 
Join Date: Nov 2010
Location: Sedro-Woolley, WA
Posts: 987
Default Re: Wind Wing Glass - Closed Car

Quote:
Originally Posted by Joop View Post
.
I see you have a phaeton SSSSsteamer Bob is talking about a closed car his Victoria.
Hi Bob, Yep, I also have 4 closed Model A Fords. I too was also referring to the closed cars. Attached is our 1929 Model A Ford that also has the same type of windwings. They make a big improvements on the quality of ride when the windows are rolled down. We also have three Stanley steam cars. 1909, 1911, and a 1914. I copied my roadster top for our 1914 Stanley from a 1914 owned by a Bidonde. Not sure of the spelling. Maybe it was Bionde.
Attached Images
File Type: jpg 1929 Model A Tudor.jpg (70.1 KB, 7 views)
SSsssteamer is offline   Reply With Quote
Old Today, 10:46 AM   #6
Bob Bidonde
Senior Member
 
Bob Bidonde's Avatar
 
Join Date: May 2010
Location: Long Island, NY
Posts: 1,714
Default Re: Wind Wing Glass - Closed Car

I did a test fit of the A-18000-C Wind Wings by Vintique on the driver's door of my 190A. Be aware that this set of wind wings requires modifications to fit them to a car. The issues I see so far:
> No installation instructions;
> Tempered glass, so it cannot be trimmed to improve its fit;
> Glass for slant windshield cars has an odd shape, so they have a top and a bottom and a one-way fit. The top & bottom of the glasses are not marked;
> Glass shape is a poor fit in the brackets, so the brackets will need to be modified to get a better position of the glass;
> Glass setting material is old, it stinks (out gassing) and it easily cracks;
> Oval head machine screws that pinch the mounting brackets to clamp the journals of the brackets that hold the glass are too long;
> Thread pitch of the oval head screws that attach the mounting brackets to the doors is too coarse;
> Mounting brackets lack gaskets to protect the paint on the car doors.


I value the function of the wind wings enough that I will not return them. To the contrary, I will post here what I windup doing to make the Vintique Wind Wings fit.
__________________
Bob Bidonde

Last edited by Bob Bidonde; Today at 10:53 AM. Reason: Formatting
Bob Bidonde is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 01:03 PM.