Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 11-28-2014, 09:11 PM   #41
CC33
Senior Member
 
CC33's Avatar
 
Join Date: Jan 2011
Location: Massachusetts
Posts: 465
Default Re: 1933 can't start after recent restart

You would need 6 volts going to the starter switch, and continuity for the ammeter lead, generator cutout, and ignition switch, to start the engine and charge the battery. The ammeter, generator cutout, and ignition switch leads should all be connected, (common), at one end of the fuse block. That will be the "hot" side.
Forget the blowing fuse for now. That only controls the lighting system as previously mentioned. Just get the engine running, then plan on a complete wire harness replacement. It will eliminate future headaches. With wiring that old, it just isn't worth the time to try to splice and repair all of the worn and broken conductors.
Does that help?
CC33 is offline   Reply With Quote
Old 11-28-2014, 09:21 PM   #42
FrankWest
Senior Member
 
FrankWest's Avatar
 
Join Date: Sep 2013
Posts: 3,002
Default Re: 1933 can't start after recent restart

Quote:
Originally Posted by quickchange34 View Post
Do you know how to use a volt ohms meter and a test light. They will really help.
yes
I have a cheap volt meter
I mainly us it for contuinity check but have also measured the voltage at 6.2 volts from my battery so I can use that.
a test light may be better because otherwise I have to hold the flashlight in my teeth.

continuity i understand open give infinite resistance.
Taking the measure readings gets confusing as to where I place the probes.
I guess from - wire to positive or the frame.
FrankWest is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 11-28-2014, 09:26 PM   #43
CC33
Senior Member
 
CC33's Avatar
 
Join Date: Jan 2011
Location: Massachusetts
Posts: 465
Default Re: 1933 can't start after recent restart

To test the continuity of a conductor, you are just making sure that the conductor, (wire), has a continuous path from end to end. Just place one probe of the ohms meter to one end of the conductor, and the other probe to the opposite end of the conductor. Look at the ohms meter to determine if you have a short. Which you should. It's best to have alligator clips on the meter probe tips for this.
If you do not see a short when doing this, you have an open condition in that conductor. (Broken wire)
CC33 is offline   Reply With Quote
Old 11-28-2014, 09:35 PM   #44
FrankWest
Senior Member
 
FrankWest's Avatar
 
Join Date: Sep 2013
Posts: 3,002
Default Re: 1933 can't start after recent restart

Quote:
Originally Posted by CC33 View Post
You would need 6 volts going to the starter switch, and continuity for the ammeter lead, generator cutout, and ignition switch, to start the engine and charge the battery. The ammeter, generator cutout, and ignition switch leads should all be connected, (common), at one end of the fuse block. That will be the "hot" side.
Forget the blowing fuse for now. That only controls the lighting system as previously mentioned. Just get the engine running, then plan on a complete wire harness replacement. It will eliminate future headaches. With wiring that old, it just isn't worth the time to try to splice and repair all of the worn and broken conductors.
Does that help?
Sounds great, thanks a lot. I plan to replace. 80 year old wiring in the walls of a home are bad enough I can just imagine 80 year old wiring exposed to the weather It was amazing that this car worked at all. The motor really sounded smooth and quiet
FrankWest is offline   Reply With Quote
Old 11-28-2014, 09:45 PM   #45
Charlie Stephens
Senior Member
 
Join Date: May 2010
Location: Southern California
Posts: 7,017
Default Re: 1933 can't start after recent restart

When you replace the wiring don't try and do it yourself using bulk wire from the local auto parts store. Buy a harness from one of the suppliers, it will be cheaper and better in the long run. See the archives for who is best and/or post the question.

Charlie Stephens

Last edited by Charlie Stephens; 11-28-2014 at 11:37 PM.
Charlie Stephens is offline   Reply With Quote
Old 11-29-2014, 12:55 AM   #46
ford38v8
Senior Member
 
ford38v8's Avatar
 
Join Date: Jul 2011
Location: SF Bay Area
Posts: 6,616
Default Re: 1933 can't start after recent restart

Sponsored Links (Register now to hide all advertisements)
Frank, Where are you located? There are so many V8ers out there very willing and capable of helping you get your beautiful car running, they can do it all or give you personal one-on-one instruction if you like. You just have to get that thing running, you owe it to yourself and to your Ford!

Tell us where you are? What city? We can help in person, but it's so hard by this long distance method!
__________________
Alan
ford38v8 is offline   Reply With Quote
Old 11-29-2014, 05:05 AM   #47
Mart
Senior Member
 
Mart's Avatar
 
Join Date: May 2010
Location: Solihull, England.
Posts: 8,732
Default Re: 1933 can't start after recent restart

If it is wired right, there is a problem in the lighting circuits causing the fuse to blow, and you are right, the fuse blowing would not stop the ignition from working.

Coincidentally, Frank, your coil is visible in the top of that pic. You were asking about that before. It may be worth looking at both the HT and low tension wires to and from that coil.

(I wrote this as a reply to the last post on page 2, missed the posts above.)

Frank, it's worth getting a "headlight" type flashlight that sits on a strap round your forehead. Very helpful when working in these out of the way areas.

Mart.

Last edited by Mart; 11-29-2014 at 05:21 AM.
Mart is offline   Reply With Quote
Old 11-29-2014, 07:12 AM   #48
Kerk
Senior Member
 
Join Date: May 2010
Posts: 642
Smile Re: 1933 can't start after recent restart

I had a similar experence with a 32 ""B"" Wagon after a tour of over 1000 miles. The owner wanted the car moved to a different location before snow came. Started on a cold N.E morning som was letting it warm before moving it. As we wee taalging it just quit ! It turned out to be the condenser. justmy experience. Kerk
Kerk is offline   Reply With Quote
Old 11-29-2014, 10:28 AM   #49
FrankWest
Senior Member
 
FrankWest's Avatar
 
Join Date: Sep 2013
Posts: 3,002
Default Re: 1933 can't start after recent restart

Quote:
Originally Posted by Mart View Post
If it is wired right, there is a problem in the lighting circuits causing the fuse to blow, and you are right, the fuse blowing would not stop the ignition from working.

Coincidentally, Frank, your coil is visible in the top of that pic. You were asking about that before. It may be worth looking at both the HT and low tension wires to and from that coil.

(I wrote this as a reply to the last post on page 2, missed the posts above.)

Frank, it's worth getting a "headlight" type flashlight that sits on a strap round your forehead. Very helpful when working in these out of the way areas.

Mart.
I appreciated your good advice before and replaced the HT wire because it as badly crystallized and insulation was off inseveral places and it broke as I twisted it. It thought that may be it.
But had to replace it anyway. Replaced the coil and condenser too.
FrankWest is offline   Reply With Quote
Old 11-29-2014, 10:35 AM   #50
FrankWest
Senior Member
 
FrankWest's Avatar
 
Join Date: Sep 2013
Posts: 3,002
Default Re: 1933 can't start after recent restart

Quote:
Originally Posted by ford38v8 View Post
Frank, Where are you located? There are so many V8ers out there very willing and capable of helping you get your beautiful car running, they can do it all or give you personal one-on-one instruction if you like. You just have to get that thing running, you owe it to yourself and to your Ford!

Tell us where you are? What city? We can help in person, but it's so hard by this long distance method!
I plan to keep working on it.
I love this car!
It is 99%original and I want to keep it that way.
produced in July of 1933 it has special significance for me.
Thanks for all your help.
I will call in the experts if everything I try does not work.
I actually have a spare rebuild model B motor and trans too. I bought them
because I plan to drive this car until I die.
FrankWest is offline   Reply With Quote
Old 12-01-2014, 10:51 AM   #51
FrankWest
Senior Member
 
FrankWest's Avatar
 
Join Date: Sep 2013
Posts: 3,002
Default Re: 1933 can't start after recent restart

Quote:
Originally Posted by CC33 View Post
You would need 6 volts going to the starter switch, and continuity for the ammeter lead, generator cutout, and ignition switch, to start the engine and charge the battery. The ammeter, generator cutout, and ignition switch leads should all be connected, (common), at one end of the fuse block. That will be the "hot" side.
Forget the blowing fuse for now. That only controls the lighting system as previously mentioned. Just get the engine running, then plan on a complete wire harness replacement. It will eliminate future headaches. With wiring that old, it just isn't worth the time to try to splice and repair all of the worn and broken conductors.
Does that help?

with ignition switch on
Have 6 volts at switch
6 volts at each coil terminal of brand new ignition coil
6 volts at generator cutoff
Test spark with spark/ coil polarity tester....NOthing lit up.
NO spark through Band new HT wire!!!!!
Looks like nothing is going thru my HT wire????
Could this new coil be bad?????
FrankWest is offline   Reply With Quote
Old 12-01-2014, 11:19 AM   #52
Bob C
Senior Member
 
Join Date: May 2010
Location: So Cal
Posts: 8,713
Default Re: 1933 can't start after recent restart

I'd be looking at the points.

Bob
Bob C is offline   Reply With Quote
Old 12-01-2014, 11:39 AM   #53
Charlie Stephens
Senior Member
 
Join Date: May 2010
Location: Southern California
Posts: 7,017
Default Re: 1933 can't start after recent restart

Quote:
Originally Posted by FrankWest View Post
with ignition switch on
Have 6 volts at switch
6 volts at each coil terminal of brand new ignition coil
6 volts at generator cutoff
Test spark with spark/ coil polarity tester....NOthing lit up.
NO spark through Band new HT wire!!!!!
Looks like nothing is going thru my HT wire????
Could this new coil be bad?????
Unfortunately, unlike in the old days, a coil (or any part) being new doesn't necessarily mean it is good. Don't replace too many parts at one time or you may end up looking for multiple problems. I once helped a person start a Model A. It turned out his points were adjusted too wide and didn't close. Did you check the voltage on both sides of the points?

Charlie Stephens
Charlie Stephens is offline   Reply With Quote
Old 12-01-2014, 12:46 PM   #54
FrankWest
Senior Member
 
FrankWest's Avatar
 
Join Date: Sep 2013
Posts: 3,002
Default Re: 1933 can't start after recent restart

Quote:
Originally Posted by Charlie Stephens View Post
Unfortunately, unlike in the old days, a coil (or any part) being new doesn't necessarily mean it is good. Don't replace too many parts at one time or you may end up looking for multiple problems. I once helped a person start a Model A. It turned out his points were adjusted too wide and didn't close. Did you check the voltage on both sides of the points?

Charlie Stephens
I will check now....should one point be 0 volts and the other one 6 volts?
FrankWest is offline   Reply With Quote
Old 12-01-2014, 12:57 PM   #55
George/Maine
Senior Member
 
George/Maine's Avatar
 
Join Date: May 2010
Location: Mid coast Maine
Posts: 1,878
Default Re: 1933 can't start after recent restart

If your points are about .014-,015 both, remove to condense wire and use the ohms scale. turn over engine and should see make and brake.
With the point wire off coil place meter there on volts. other end on battery neg.
should read about 5 volts if under dash resister is hooked up.
Also check the end of wire connector at coil make sure it not held on by few strands on wire.
George/Maine is offline   Reply With Quote
Old 12-01-2014, 02:41 PM   #56
FrankWest
Senior Member
 
FrankWest's Avatar
 
Join Date: Sep 2013
Posts: 3,002
Default Re: 1933 can't start after recent restart

Quote:
Originally Posted by George/Maine View Post
If your points are about .014-,015 both, remove to condense wire and use the ohms scale. turn over engine and should see make and brake.
With the point wire off coil place meter there on volts. other end on battery neg.
should read about 5 volts if under dash resister is hooked up.
Also check the end of wire connector at coil make sure it not held on by few strands on wire.
I pulled the hT wire out of the distributor and measure 6 volts with the ignition on.
So I guess the problem is with the distributor??
FrankWest is offline   Reply With Quote
Old 12-01-2014, 04:03 PM   #57
FrankWest
Senior Member
 
FrankWest's Avatar
 
Join Date: Sep 2013
Posts: 3,002
Default Re: 1933 can't start after recent restart

If I slowly hand crank the engine to see how close the points gets at the closest point and what should that distance be? 0.15 inch
FrankWest is offline   Reply With Quote
Old 12-01-2014, 04:07 PM   #58
V8COOPMAN
Senior Member
 
V8COOPMAN's Avatar
 
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,106
Default Re: 1933 can't start after recent restart

The points should close. If they never close, the car will never run. They should open approx. .015 every time a cylinder fires, and then close again. DD
__________________
Click Links Below __


'35-'36 W/8BA & MECHANICAL FAN


T5 W/TORQUE TUBE
V8COOPMAN is offline   Reply With Quote
Old 12-01-2014, 04:45 PM   #59
George/Maine
Senior Member
 
George/Maine's Avatar
 
Join Date: May 2010
Location: Mid coast Maine
Posts: 1,878
Default Re: 1933 can't start after recent restart

I don't know why you put the meter in the high tension hole better stick our finger in there. LOL

Try this test.
Once you see spark then get the point working.
At the high point of lobe that's were the air gap is .015 get a feeler gauge.

Here is a simple way to check coil and condener.
Put power to coil make sure there are no broken strands end of wire.
Remove points wire at coil
Now put a condenser on coil lug terminal wire end.
Take coil wire out of cap and hold 1/4 to grd.
leave other end in coil.
Get a piece of wire grd one end and touch conderser.
When you make contact and remove should see spark.
Turn key on.
George/Maine is offline   Reply With Quote
Old 12-01-2014, 06:51 PM   #60
FlatheadTed
Senior Member
 
FlatheadTed's Avatar
 
Join Date: May 2010
Location: Auckland
Posts: 4,691
Send a message via AIM to FlatheadTed
Default Re: 1933 can't start after recent restart

(1) with key on.
(2)HT wire removed from dizzy, held 1/4 to ground .
(3) turn the motor till points are closed .
(4) open and close points with a screw driver .
(5) spark should jump off the HT wire .

Ted
__________________
http://www.flatheadted.com


Flathead Ted brake Floaters ,
FlatheadTed is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 06:10 PM.