Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 10-28-2019, 11:23 PM   #1
Bigphil
Junior Member
 
Join Date: Jun 2010
Posts: 20
Cool Hydraulic brake adjustments.

Hydraulic brake adjustments.
I have 1940 Ford hydraulic brakes on my 1931 Model A Ford.
All cylinders are brand new with new rubber. And New Brake shoes.
This system has about 500 miles on it.

I recently had to change the brake light switch on the master cylinder.
My son and I bled the system after installing the brake light switch.

The brakes do not stop the car as well as it did before bleeding the system.

How do I tell if the problem is air in the system or too much brake shoe clearance ?
Bigphil is offline   Reply With Quote
Old 10-29-2019, 03:31 AM   #2
mrtexas
Senior Member
 
mrtexas's Avatar
 
Join Date: May 2010
Location: Sugar Land, TX
Posts: 4,393
Default Re: Hydraulic brake adjustments.

Good luck with Lockheed brakes. I gave up on them and use repro bendix brakes. Way easier to adjust. Your problem is probably too much air and brake shoe clearance. If you arch the shoes to new drums you have a chance to make 40 brakes work. Much easier is using DOT 3 brake fluid. I gave up on DOT 5 as it is much more difficult to bleed and get a firm pedal. If you send your Model A mechanical brakes off and get them restored by Synders for approx $2,000 a set then they can stop as well as hydraulics. I did that twice for Model A. https://mrtexasmodela.weebly.com/4648brakes.html

https://sites.google.com/site/mrtexa...ydraulicbrakes
__________________
41 woodie https://41fordwoodie.weebly.com/
mrtexas is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 10-29-2019, 06:48 AM   #3
glennpm
Senior Member
 
glennpm's Avatar
 
Join Date: Sep 2014
Location: Wiscasset, Maine
Posts: 1,965
Default Re: Hydraulic brake adjustments.

Hi,


So since this started with the recent brake bleeding, you probably have your shoes adjusted properly.



Did you bleed the brakes starting from the furthest brake form the master cylinder, usually right rear for LHD, working into the closest? Does the brake pedal feel soft and spongy now? This will indicate air is still in the system. Are all the bleeders tight with no evidence of leakage?


I have also made a practise of putting pressure on the brake pedal overnight by wedging a piece of wood between the seat and the pedal to keep a little constant pressure on the system. It helps to get the last of the air bubbles to migrate back to and get released at the master cylinder.


I also prefer DOT 3 and 4 brake fluid. 4 is what I use after bad experience with DOT 5 but that's another discussion!


Glenn

Last edited by glennpm; 10-30-2019 at 06:07 AM.
glennpm is online now   Reply With Quote
Old 10-29-2019, 08:06 AM   #4
JSeery
Member Emeritus
 
JSeery's Avatar
 
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
Default Re: Hydraulic brake adjustments.

The problem started with the change of the brake light switch and bleeding the system, so it stands to reason that there is still some air in the lines. I would try bleeding it again.
JSeery is offline   Reply With Quote
Old 10-29-2019, 09:24 AM   #5
19Fordy
Senior Member
 
19Fordy's Avatar
 
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,873
Default Re: Hydraulic brake adjustments.

I know this is of little importance but, when I changed the brake light switch on my stock 40, I didn't have to bleed or adjust the brakes. Wonder why you didn't have the same experience. In any case, you will prevail.
19Fordy is offline   Reply With Quote
Old 10-29-2019, 01:09 PM   #6
Ken/Alabama
Senior Member
 
Ken/Alabama's Avatar
 
Join Date: May 2010
Location: Alabama
Posts: 3,237
Default Re: Hydraulic brake adjustments.

Sponsored Links (Register now to hide all advertisements)
Quote:
Originally Posted by 19Fordy View Post
I know this is of little importance but, when I changed the brake light switch on my stock 40, I didn't have to bleed or adjust the brakes. Wonder why you didn't have the same experience. In any case, you will prevail.
Me too & I’ve been using dot 5 in my 40 for the last 23 years without any issues.
Ken/Alabama is offline   Reply With Quote
Old 10-30-2019, 02:01 PM   #7
badassfrombadaxe
Junior Member
 
Join Date: Jul 2019
Posts: 15
Default Re: Hydraulic brake adjustments.

I consulted the hydraulics section of Ford V8 Service Bulletins 1938-1940 Complete on it's pg 459 and it suggests that the free play in the pedal if made zero results in blocking the bypass port so fluid cannot get back into the reservoir. It also says this condition could come from the rubber swelling due to improper fluid mineral oil instead of alcohol or M3833 fluid in cleaning the parts. Did I spend wisely with Amazon to obtain this book or is it too far from the common man?
badassfrombadaxe is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 03:05 PM.